Marantz RC9200 Manuel utilisateur

User Guide

To The

RC9200/RC5200

Touch Screen Remote

Controls

Automating Your

Home Theater

With Marantz

Automating Your Home Theater With The Marantz RC9200/5200

RC9200/5200 Remote Control User Guide

The in ormation in this manual is copyright-protected. No part o this manual may be

copied or reproduced in any orm without prior written consent rom Marantz Europe

B.V.

MARANTZ EUROPE B.V. CORPORATION SHALL NOT BE LIABLE FOR OMIS-

SIONS OR FOR TECHNICAL OR EDITORIAL ERRORS CONTAINED IN THIS

MANUAL. MARANTZ EUROPE B.V. SHALL NOT BE HELD LIABLE FOR INCIDEN-

TAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE SUPPLYING OR

USE OF THIS INFORMATION. MARANTZ EUROPE B.V. SHALL NOT BE HELD LIA-

BLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE

PERFORMANCE OR USE OF THE MATERIALS DESCRIBED IN THIS MANUAL.

The in ormation in this manual may be subject to change without prior notice.

All other brand or product names are trademarks or registered trademarks o their

respective companies or organizations.

FCC NOTICE: This equipment has been tested and ound to comply with the limits or

a Class B digital device, pursuant to part 15 o the FCC rule. These limits are

designed to provide reasonable protection against harm ul inter erence in residential

installation. This equipment generates, uses, and can radiate radio requency energy

and , i not installed and used in accordance with the instructions, may cause harm ul

inter erence to radio communications. However, there is not guarantee that inter eren-

ce will not occur in a particular installation. I this equipment does cause harm ul inter-

erence to radio or television reception, which can be determined by turning the

equipment o and on, the user is encouraged to try to correct the inter erence by one

or more o the ollowing measures:

■Reorient or relocate the receiving antenna.

■Increase the separation between the equipment and receiver.

■Connect the equipment into an outlet on a di erent circuit rom the receiver.

■Consult the dealer or an experienced radio/TV technician or help.

Note I serial or parallel ports are con igured, a iltered/shielded serial or paral-

lel cable is recommended to minimize EMI and ensure FCC class B

compliance.

User Guide

Introduction 2

1. The Marantz RC9200/5200 2

2. The Battery 3

Getting Started 6

1. Activating the RC9200/5200 6

2. Navigating Control Panels 7

3. Operating a Device 12

4. Check Battery Li e - The INFO Panels 13

5 The Setup Panels 13

6. The Mode Menus 15

Customizing Your RC9200/5200 17

7. Managing Memory 17

1. Introduction 18

2. Cloning All Your Existing Remotes 18

3 Complex Operation? Macros or Help... 20

4. Programming Help Lists 22

5. Macro/Panel Jump Capabilities 23

6. Programming Macros & Panel Jumps 24

7. Macros From Your Home Buttons 26

Re erence 28

1. Programming Buttons 28

2. Labeling Buttons, Frames and Menu Items 32

3. Working with Device and Macro Groups 35

4. Deleting and Restoring 40

5. Recording Macros 43

6. Using the Remote Control with Radio Frequency 47

7. Touch Screen Setup 50

Troubleshooting 52

Frequently Asked Questions 55

Overview o Symbols 57

Speci ications 59

The Revert Con iguration 60

Index 61

Table of Contents

User Guide

The RC9200/5200 is designed to control most devices that understand

in rared remote control signals. Its easy-to-use touchscreen and its intuiti-

ve inter ace make it a per ect remote control or every user. The

RC9200/5200 is completely customizable and programmable. You can

add devices and unctions, relabel buttons, record macros and animate

your macros. Although the RC9200/5200 is pre-programmed or Marantz

components, a vast collection o built-in tab guided panels with pre-arran-

ged button art enables you to easily choose the per ect inter ace or any

non-Marantz component. The RC9200/5200 easily “learns”commands

rom the vast majority o manu acturers’remote controls.

Introduction

1. The Marantz RC9200/5200

The Volume, Channel

and Mute buttons are

typically programmed to

always work the same

way regardless o what

panel is displayed.

The In rared Eye

transmits to your

devices and learns

rom your existing

remotes.

The Touchscreen

The INFO button

enables you to check batte-

ry li e.

Back and Ahead buttons

enable you to quickly navi-

gate the last six screens

you’ve viewed.

\Menu, Enter, Exit and 4

way navigator buttons will

change their unction

depending on what device

you are controlling.

The Contrast Dial

adjusts the appe-

arance o the

screen.

The Backlight but-

ton lights up the

screen (you can

adjust the length o

time it stays on,

see page 13).

The Serial Port ena-

bles you to program

the RC9200/5200

on a Windows PC.

The Home B utton

always takes you

back to the Main

Home Panel Control

Screen (think o it

as the Start button).

User Guide

Introduction

Tap the Mode Button:

to access the Mode

Menus. They are di e-

rent based on the type

o panel you last dis-

played. Use the Mode

Menus to customize

your remote.

DevicesMacros Home

Tap the Scroll Arrows:

to scroll to other panels within the

active group.

Tap the Macro menu Bar:

to use your one touch

Macro buttons. Tap again

and a menu o all o your

Macro groups appears.

Tap again to select:

Tap the Device

menu bar:

to operate devices.

Tap again and a

menu o all your

devices appears.

Tap again to select:

Panel number:

shows active

control panel

Tap the Scroll Arrows:

to scroll to other

panels within the acti-

ve group.

2. The Battery

When you use the Remote Control or the irst time, you will have

to:

•install the battery pack;

•place the Remote Control in the docking station and charge the

Remote Control.

•tap the INFO button on the Home Panel to check battery

li e.

Warning Use the docking station only with the Philips NiMH rechargeable

battery pack.

We strongly advise you not to plug other appliances (like mobile

phones, PDA’s) into the docking station. This will damage both

the connector and the appliance.

Use the Control Panel

Buttons:

to operate your compo-

nents

User Guide

Installing the Battery Pack

1 Press the latch on the battery cover and remove the battery

cover rom the Remote Control.

2 Place the battery pack in the battery compartment.

3 Plug the cable o the battery pack in the connector as illustrated.

4 Place the battery cover back on.

Note Make sure the cable o the battery pack does not get stuck

between the molded interior and the battery cover.

A ter a ew seconds, the Remote Control starts up automatically

and an Introduction screen appears. The Remote Control beeps

twice to indicate that it has inished starting up.

Because the battery pack o the Remote Control is not ully pre-

charged, you will have to charge it as described below.

Introduction

User Guide

Charging the Remote Control

For charging the Remote Control you use the docking station.

1 Plug the power adapter into a wall outlet and connect it to the

docking station.

2 Place the Remote Control in the docking station.

Make sure you hold the Remote

Control at an angle o 30° to 45°

when you place the it in the

docking station.

Charging starts immediately. The green charging LED on the

ront o the docking station indicates charging takes place.

When the Remote Control is ully charged, the LED goes o .

Note Normal charging time is 2 to 3 hours, depending on the

condition o the battery pack.

You can operate the Remote Control while it is being charged.

The battery pack does not have to be entirely empty be ore

recharging.

You can place the Remote Control in the docking station at any

time.

When the battery pack is running low, the Low Battery icon lashes

at the top o the screen. Recharge the Remote Control as soon as

possible to ensure per ect per ormance.

Note The RC9200/5200 retains all settings when the battery is comple-

tely dead. You will only have to reset the clock.

Introduction

User Guide

Turning on the Display

Tap the screen gently with your inger or a blunt, so t object like

a pencil eraser.

The display is activated and you see the Home panel.

Notes ·I the display stays blank or becomes black, adjust

the contrast dial on the le t side.

·I another panel is displayed, tap the Home button .

·The RC9200/5200 shuts down automatically a ter being le t

alone or a ew seconds (you can adjust the time out period in

the Setup panels).

Using the Backlight

Press the backlight button on the le t side.

The backlight shuts o a ter a ew seconds to save power.

Note In the settings (see page 13) you can choose to activate the

backlight automatically when you turn the RC9200/5200 on.

Modes

The RC9200/5200 has di erent “modes.”When you activate the

RC9200/5200 or the irst time, it starts up in Use mode allowing

you to immediately operate your devices.In Use mode the menu

bar at the bottom o the screen displays the symbol or the

Mode Menu. Tap the symbol. A menu will pop up with USE as

an option. I the menu bar shows another symbol, like , tap it

to reveal the Mode menu and tap USE to return to normal opera-

ting mode.

Note I you do not see the mode menu symbol; it has been

deactivated via the Setup panel. Press and hold the center o

the bottom menu bar to overide the Mode menu deactivation.

Getting Started

1. Activating the RC9200/5200

User Guide

Three Divisions o Control Panel Types

Your RC9200/5200 is capable o displaying hundreds o di erent

control screens. By grouping them into sensible divisions, it is easy

to navigate to the control panel you want. The three main divisions

are:

Home —The Home group disp-

lays convenient instant jump buttons

to the main control panels o your

system devices (your VCR, TV, CD

player etc.). These buttons

also select the Input o your Home

Theater Receiver or Preamp (Home

buttons are linked to the Device

pull down menu, which also selects

inputs on your receiver).

Access Home by tapping

the Home button at the

bottom le t o the remote.

Devices —The Device side

displays the control panels o your

components, one device group at a

time. A button on a Device panel

will act just like the buttons on the

original remote control. You can

always select the Device

side o the RC9200/5200 by tapping

the menu bar to the right o the

remote icon.

Getting Started

2. Navigating Control Panels

Tap to select the Device side

o your RC9200/5200 .

User Guide

Macros —The Macro side o your

RC9200/5200 displays Macro buttons.

Macro buttons play back a sequence

o up to 255 di erent commands (and

panel jumps, which can be pro-

grammed to do crude animations or

to give messages during the Macro).

You can always select the Macro side

o the RC9200/5200 by tapping the

menu bar to the le t.

Using Menus to Jump to a Panel Group

1 Navigate to either the Macro (le t) or the Device (right) side o

the remote by tapping the le t or right menu bar.

2 Tap the Menu bar again. A menu will pop into view, enabling you

to choose which group o panels you want. I you have a large

system with more than seven groups, scroll arrows enable

you to select those that are out o sight.

3 A ter using the scroll arrows to view all o the choices, simply

tap the label o the group you would like.

Note When you jump to a Device, the RC9200/5200 will change the

input o your home theater receiver/preamp (using the pull down

menus is exactly the same thing as pressing a Home button).

Tap to select the Macro side o your

RC9200/5200.

Device Groups

Macro Groups

Getting Started

Autres manuels pour RC9200

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Marantz Télécommande

Marantz

Marantz RC5000i Manuel utilisateur

Marantz

Marantz RC-9500 Manuel utilisateur

Marantz

Marantz RC3200 Manuel utilisateur

Marantz

Marantz RC3200 Manuel utilisateur

Marantz

Marantz RC5200 Manuel utilisateur

Marantz

Marantz RC-5400 Manuel utilisateur

Marantz

Marantz RC3001/E1B Manuel utilisateur

Marantz

Marantz RC-9500 Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Marantz

Marantz RC101 Guide de démarrage rapide

Marantz

Marantz RC1200 Manuel du propriétaire

Marantz

Marantz RC101 Manuel utilisateur

Marantz

Marantz RC-1400 Manuel utilisateur

Marantz

Marantz RC-1400 Manuel utilisateur

Marantz

Marantz RC9001 Manuel utilisateur

Marantz

Marantz Professional RC600PMD Manuel utilisateur

Marantz

Marantz RC3200 Manuel utilisateur

Marantz

Marantz RC2001 Manuel utilisateur

Marantz

Marantz RC5000 Manuel utilisateur

Marantz

Marantz RC-9500 Manuel utilisateur

Marantz

Marantz RC-1400 Manuel utilisateur

Marantz

Marantz RC-9500 Manuel utilisateur

Marantz

Marantz RC2000MKII Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation

Invacare

Invacare G91S Manuel utilisateur