Marantz RC1200 Manuel utilisateur

Model

RC1200

User Guide

Learning

Remote Control

ENGLISH

MAIN FEATURES & FUNCTIONS ........ 2

NAMES OF PARTS & FUNCTIONS ..... 3

LOADING BATTERIES.......................... 8

BASIC OPERATION .............................. 9

USE MODE .............................................................9

LEARN MODE ......................................................10

PROGRAMMING THE JOG DIAL.........................13

REWRITING NAMES ............................................14

ERASING PROGRAMMED CODES......................16

PROGRAMMING MACROS .................................20

EDITING MACROS ...............................................22

USING MACROS ..................................................24

EXAMPLES OF MACRO PROGRAMS ................ 25

CLEARING MACRO PROGRAMS .......................28

USINGTHE CLONE MODE ................ 29

COPY MODE ....................................... 32

COPYING ON A BUTTON BY BUTTON BASIS ...32

COPYING THE JOG DIAL INFORMATION ..........34

OTHER FUNCTIONS........................... 36

LIGHTING BUTTON .............................................36

LUMINOUS BUTTONS ......................................... 36

SETUP ..................................................................36

JOG DIAL COMMAND FUNCTIONS LISTING...

SPECIFICATIONS ............................... 43

ENGLISH

MAIN FEATURES & FUNCTIONS

• PROGRAMMABLE LEARNING

FUNCTION

Can easily be programmed to learn the codes

for almost any other infrared-based remote,

allowing the remote control functions for many

different components to be consolidated

conveniently in a single unit.

This remote controller uses a non-volatile

memory so that the learned codes will be

retained even if the batteries are removed.

• PRESET CODES

Function buttons already contain preset codes

(using the RC-5/RC-6 remote control

language) for other remote-controllable

Marantz audio-visual component.

(This does not apply to some of the buttons.)

• LCD LIGHTING FUNCTION AND

LUMINOUS BUTTONS

To allow easy use in a location which has been

darkened for a home theater performance, for

instance, this remote controller features an

LCD backlight with electroluminescence (EL)

and luminous buttons which can store light.

• LARGE, EASY-TO-READ DISPLAY

Large LCD (liquid crystal display) messages

and other information at a glance.

• JOG DIAL

The function selected by Jog Dial (displayed

on the LCD) can be operated directly by the

enter button.

• MACRO CAPABILITY

Macro function allows the remote controller to

be programmed to execute complex strings of

multiple commands using a single keystroke.

• NAME ASSIGNMENT

Allows one to change the (displayed via the

LCD) name for a function button.

• CLONING FUNCTION

The unit features a cloning system that

enables a duplicate unit of this remote

controller which has already been

programmed to be easily made by

undertaking a series of key operations.

ENGLISH

NAMESOFPARTS &FUNCTIONS

Names of Buttons & Functions

zMODE button

Used to change the operation mode of the

remote controller. Pressing this button cycles

the remote controller through USE →LEARN

→NAME →CLONE TX → CLONE RX →

USE, with the currently selected mode

displayed on the LCD.

xMACRO button

Used to store a string of consecutive button

operations in the memory and also to revise

them.

Pressing it switches the remote controller in

and out of the MACRO mode. Its status is

displayed on the LCD.

cPower ON and OFF

buttons

Used to turn ON and OFF the power of the

amplifier or receiver or turn ON and OFF the

power of a source component which has its

own ON and OFF buttons.

vSource ON/OFF button

Used to turn specific sources (such as DVD

players, etc.) ON and OFF independently from

the rest of the system.

bLCD

Used to display information about currently

selected modes and functions.

nENT buttons

Used to execute a function selected with the

Jog Dial m.

There are 2 ENT buttons, one on each side, so

that the remote controller can be used just as

easily with either hand.

The characters on the display can also be

programmed.

mJog Dial

Used to select the operation content for each

source. Ten types of direct operation are

possible for each of the 11 functions including

LD, TV, AMP, etc. After selecting the desired

function, press either of the ENT buttons nto

transmit the signal.

ENGLISH

,Function buttons

Used to switch the remote controller to the

command sets for specific sources (amplifier,

receiver, etc.), thereby allowing a single remote

controller to control up to 11 different

components. To use these buttons to switch the

amplifier’s source, press the desired button

twice within 2 seconds. The AMP button ,is

used only to switch the command set of the

remote controller itself and therefore does not

transmit any signal. Further, the function

buttons may also be programmed to execute

macros. (A macro allows a complex string of

operations to be performed in series simply by

pressing a single button.) One button can be

programmed to learn sequences containing up

to 10 commands. The following is an example

of a macro sequence:

Turn the receiver ON →Switch the function to

DVD →Set the Surround Mode to Dolby

Digital →Switch the TV to video input →Set

the DVD player to Play.

.VOLUME up / down

button

Used to adjust the volume on receivers and

other components equipped with volume

control.

⁄0 CURSOR/CONTROL buttons

Used to operate on-screen and other displays

used by amplifiers and other components, as

well as to operate the PLAY, STOP, PAUSE,

NEXT, and PREVIOUS functions of each source.

⁄1 < • 3(CURSOR/ CONTROL

switching) button

Used to switch the function of the CURSOR/

TRANSPORT CONTROL buttons ⁄0 between

CURSOR and TRANSPORT CONTROL, with

the currently selected function displayed on

the LCD when the DVD, LD, or VCR functions

are selected. When functions other than DVD,

LD, or VCR are selected, the <• 3button

remains inactive.

⁄2 Channel up / down

button

Used to controls the up/down function of TV tuner,

or allows one to cycle through the tuner presets.

⁄3 MUTE button

Used to temporarily mute the sound for

preamplifiers, receivers, etc.

ENGLISH

⁄4 GUIDE button

Used to call up the on-screen menus used to

control DVD players, digital satellite systems

(DSS), and other menu-equipped systems.

⁄5 CLEAR button

Used to clear the contents of memory or

programmed functions.

⁄6 MEMO button

Used to program your CD player’s track

memory, or to enter a VCR recording program,

and can be used to provide the MEMO

function included with other components in

your system.

⁄7 Ten-Key pad/Surround

Mode buttons

Used to enter numeric digits, useful for finding a

specific track on a CD, or to tune a preset radio

station, etc. When the function is set to AMP, it is

possible to choose Surround Mode, etc.

⁄8 Infrared Transmitter/

Receiver Window

Used to transmit remote control signals based

on beams of infrared light to system

components. To ensure that these signals are

properly received, make sure that this window

is pointing in the general direction of the

infrared receiver on the amplifier or other

components. This window should also be

pointed toward the source remote controller

when using Programmable Learning function.

⁄9 LIGHTING button

When this button is pressed, the LCD display

lights up, and it goes off 5 seconds later.

While it is held down, the display remains

lighted.

Note:

The programmable learning function does not

work with buttons z, x, n, ⁄1 and ⁄9.

ENGLISH

LCD (Liquid Crystal Display)

Information about currently selected functions

and modes is displayed on the LCD. Pressing

any buttons will call up a full display of

information on the status of that function or

mode. This display will disappear after

approximately 1 minute, except for the

Function Name indicator A, which is always

displayed.

AFunction Name indicator

Displays the name of the currently selected

function (LD, TV, etc.) using up to 5 characters.

BCommand Name

indicator

Displays up to 10 types of commands for each

function using up to 5 characters.

CCommand Page indicator

Allows confirmation of current command page

of Jog Dial m. Also, when setting or

transmitting macros, displays information such

as the number of macro steps and the time

intervals between command transmissions.

DTransmission indicator

Indicates when the remote controller is

transmitting a signal.

EUSE indicator

Indicates the status in which the programmed

code is output.For normal operation the USE

indicator is displayed.

FLEARN indicator

Indicates when the remote controller is in the

LEARN mode. It also appears when

programming is cleared.

ENGLISH

GNAME indicator

Indicates when the remote controller is in the

NAME mode and a function name is being

changed.

HMACRO indicator

Indicates when the remote controller is in the

MACRO programming mode.

ICURSOR indicator

Indicates when the CURSOR CONTROL

buttons are in the cursor mode.

JCONTROL indicator

Indicates when theCURSOR CONTROL

buttons are in a transport control mode such

as PLAY, STOP, etc.

NOTE:

• If the LCD flickers when a button is pressed

in order to transmit a command, the

transmission or learning is not possible. In

such a case, please replace the batteries.

Operating tip

• This remote controller uses non-volatile

memory, so that learned codes and macros

will be preserved even if the batteries are

removed.

ENGLISH

LOADING BATTERIES

The life of the batteries used with the remote

control unit is about 6 months with normal use.

Also be sure to replace batteries earlier when

you notice that they are getting weak. Do not

use alkaline, manganese, nickel-cadmium (Ni-

Cd) or other different types of batteries

together.

(1) Remove the back cover.

(2) Insert the new batteries (AA type) with

correct (+) and (–) polarity.

(3) Close until it clicks.

ENGLISH

MEMO

CLEAR

GUIDE MUTE

1 23 4 5

CD DVD

CD-R/MD

DSS TV VCR

AMP

TUNER

TAPE

AUX

AUTO DOLBY THX DTS HALL

MATRIX MOVIE 2CH OSD SLEEP

BASIC OPERATION

USE MODE

The remote controller will normally be used in

the USE mode.

It comes preset with codes commonly used to

control 11 types of components manufactured

by Marantz, Philips and RCA (for DSS),

including DSS, DVD, TV, LD, VCR, AUX,

TUNER, CD, TAPE, CD-R/MD, and AMP, as

well as many others that utilize the RC-5

remote control language.

1. Press once one of the Function buttons

,to change to another component’s

commands, such as LD button.

2. LD will be displayed on the LCD and the

function codes will be set to operate the

laser disc player, and if you double

clicked the LD function button, the

amplifier or receiver’s input will be

changed as well.

3. Now you can operate the laser disc player.

When a button is pressed, the symbol

indicates that a remote code is being

transmitted. is not displayed if a button

for which no code has been set is pressed.

4. The Jog Dial mis used to select any one

of up to 10 direct operations that can be

performed for each of the 11 functions

including LD, TV and AMP. Rotate the

Jog Dial mto select one of these

commands. The number of the current

page is indicated by - at LCD C.

The signal is sent when the ENT button n

is pressed.

Page numbers cycle up or down, for

example → → → →etc. or

→ → → →etc. depending on

which way the Jog Dial mis rotated.

The last page position for any given

command function is retained in the

memory even if the remote controller is

switched to the command function for

another component. (Last Memory)

Autres manuels pour RC1200

Table des matières

Autres manuels Marantz Télécommande

Marantz

Marantz RC9200 Manuel utilisateur

Marantz

Marantz RC9200 Manuel utilisateur

Marantz

Marantz RC5000i Manuel utilisateur

Marantz

Marantz RC-1400 Manuel utilisateur

Marantz

Marantz RC-9500 Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Marantz

Marantz RC2000MKII Manuel utilisateur

Marantz

Marantz RC9001 Manuel utilisateur

Marantz

Marantz RC-1400 Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Marantz

Marantz RC-9500 Manuel utilisateur

Marantz

Marantz RC-5400 Manuel utilisateur

Marantz

Marantz RC5200 Manuel utilisateur

Marantz

Marantz RC3200 Manuel utilisateur

Marantz

Marantz RC-5400 Manuel utilisateur

Marantz

Marantz RC3200 Manuel utilisateur

Marantz

Marantz RC3001/E1B Manuel utilisateur

Marantz

Marantz RC-1400 Manuel utilisateur

Marantz

Marantz RC-9500 Manuel utilisateur

Marantz

Marantz RC3200 Manuel utilisateur

Marantz

Marantz RC5000 Manuel utilisateur

Marantz

Marantz RC101 Guide de démarrage rapide

Marantz

Marantz RC-1400 Manuel utilisateur

Marantz

Marantz Professional RC600PMD Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation

Invacare

Invacare G91S Manuel utilisateur