Macally WIFISD2 Manuel utilisateur

www.macally.com

MEDIA HUB AND TRAVEL ROUTER

Quick Start Guide

Macally Product Information

Warranty

Macally Peripherals warrants that this product is free from defects in materials and manufacturing workmanship for the period

of one (1) year from the date of purchase. If the product is found to be defective, as your sole remedy and as the manufacturer’s

only obligation, Macally will repair or replace the product. This warranty shall not apply to products that have been subject to

abuse, misuse, tampered with or modified, abnormal electrical or environmental conditions, or any conditions other than what

we consider as normal use.

Limitation of Liability

The liability of Macally Peripherals arising from this warranty and sale shall be only limited to a refund of the original purchase

price. In no event shall Macally be liable for any costs of procurement of substitute products or services, or for any loss of profits,

or for any consequential, incidental, direct or indirect damages, however caused and or any theory of liability arising from this

warranty and sale.

These limitations shall apply not withstanding any failure of essential purpose of any limited remedy.

Australia Warranty

This document details the terms and conditions of the warranty provided with this product. Please disregard any other

representations contained on this product, its packaging, or provided with this product which constitutes or appears to constitute

a warranty.

This warranty is offered by TNS Distribution Australia Pty Ltd, Unit 1, 16 Aquatic Drive,Frenchs Forest NSW 2086 Australia, (02)

9975 0900, [email protected]

Subject to the exclusions and limitations set out below, we warrant to you that if you purchase a product directly from us, or from

any of our authorized resellers, that it will not contain defects which are a result of faulty manufacturer workmanship or materials.

This warranty subsists for 1 year from the date of purchase.

Subject to any rights you have under the Australian Consumer Law, we will not be liable for defects which are a result of damage

or loss caused by factors beyond our control, any product which has not been maintained according to any care or maintenance

instructions provided with the product, any alterations to a product which are not performed by us, or damage or defects caused

to the product due to unusual or non-recommended use. We will not be liable for any special, indirect, consequential or economic

loss or damage or loss of profits whatsoever suffered by you or any other person resulting from any act or omission by us. Our

total liability in respect of this Warranty against Defects is limited to the replacement of the goods.

Any claim made under this warranty must be made by returning the defective goods to us, at your expense. Please provide details

of the defect and evidence of purchase to [email protected] and we will provide instructions on how to obtain a

replacement. If you do not have Internet access please telephone us for further instructions.

Thank you for purchasing the Macally Media Hub and Travel Router. Please refer to

this guide to familiarize yourself with the product. This Quick Start Guide will provide

step-by-step instructions to install and use the Media Hub and Travel Router quickly.

For further details, please download the full manual from

http://us.macally.com/pages/drivers-and-downloads

Technical Support

If you are in the United States and need technical support, please call us at

1-909-230-6778 or send an email to [email protected]

Package Contents

• WIFISD2 – Media Hub and Travel Router

• Micro USB Cable

• Quick Start Guide

Hardware Basics

Internet Green LED:

Connected to internet

Battery Green LED:

Red - Low battery

Flashing Green - Charging

Solid Green - Drive on

Off - Battery full or Drive off

SD White LED:

Solid - Stand-by

Flashing - Read/Write

WiFi Blue LED:

Wi-Fi ready

Power Button:

Press and hold for 3 seconds to take effect

ON/Wi-Fi Pocket Drive Mode (Approx. 45 seconds to boot up)

OFF/USB SD Reader Mode (Approx. 6 seconds to shut down)

Micro USB:

• USB recharging port

• SD reader to a computer

Ethernet Port:

(Optional network cable)

USB Host:

• USB storage(Flash drive or hard drive)

• Power output to charge mobile devices

SD Card Slot Reset

WIFISD2 supports SD cards, USB flash drives, and USB external hard drives as

storage space. Once you have chosen which type of media you want, insert the

respective SD card, flash drive, or external USB hard drive into the WIFISD2 and

press and hold the power button for 2 seconds to boot up the wireless mode. WIFISD2

will automatically create a “Share” folder and 4 subfolders (Photos, Music, Videos,

Documents) on your selected media. Then power down the WIFISD2 and connect it

to your computer via USB and follow steps 1.1 to 1.3.

Step 1: File Copy

1.1 SD Card

Insert an SD card into the SD slot of the WIFISD2 until you feel a click. If you have a

microSD card, please use an SD card adaptor, then insert it into the SD slot of the

WIFISD2. First, turn off the WIFISD2, then connect it into any USB port on your

computer with the included micro-USB cable. Your computer will detect it as a USB

media card reader and removable drive. In the “Share” Folder you can copy all of

your media to the corresponding folders. Once the files have been copied to the

appropriate location, you can access each type of media (Documents, Photos, Music,

Video) by pressing on the tiles on the home page of the App. Then unmount and

disconnect the WIFISD2 from your computer. Press down the power button for 2

seconds to put it in Wi-Fi mode and use it as a Wi-Fi media hub and travel router.

Insert SD Card Copy files

WIFISD(Power off)

Micro USB cable

Wi-Fi pocket drive

Power on

1.2 Flash Drive

Before a USB flash drive is used in the WIFISD2, please plug your flash drive into

any USB port on your computer. Your computer will detect it as a USB removable

drive. In the “Share” Folder that was created on initial boot up, you can copy all

of your media to the corresponding folders. Once the files have been copied to the

appropriate location, you can access each type of media (Documents, Photos,

Music, Video) by pressing on the tiles on the home page of the App. Unmount and

remove the flash drive from your computer and plug it into the USB port on the

WIFISD2. Press down the power button for 2 seconds to put it in Wi-Fi mode and

use it as a Wi-Fi media hub and travel router.

1.3 External Hard Drive

To use a USB external drive, please plug your external drive into any USB port on

your computer. Your computer will detect it as a USB removable drive. In the “Share”

Folder created on initial boot up, you can copy all of your media to the corresponding

folders. Once the files have been copied to the appropriate location, you can access

each type of media (Documents, Photos, Music, Video) by pressing on the tiles on

the home page of the App. Unmount and remove the external drive from your

computer and plug it into the USB port on the WIFISD2. Press down the power button

for 2 seconds to put it in Wi-Fi mode and use it as a Wi-Fi media hub and travel router.

Copy files

Flash Drive

Insert Flash Drive Wi-Fi pocket drive

Flash Drive

Power on

Copy files

USB Drive

Insert USB Drive Wi-Fi pocket drive

USB Drive USB Drive

Power on

*Note: A 3.5” USB external hard drive must be powered by its own AC adaptor.

A 2.5” USB hard drive might be powered by the WIFISD2, however it will

drain the internal battery of the WIFISD2 much quicker than an SD card.

For first time use, or when the battery LED is red, you must charge the WIFISD2. To

charge it, please use the included micro-USB cable to plug into a USB wall or car

charger. You can also charge it through a computer’s USB port. A full charge will take

approximately 3 to 5 hours depending on the output current of the power source.

During charging, the battery LED will be flashing green. You may put the WIFISD2 in

Wi-Fi mode and use it while charging. When the battery is fully charged, the battery

LED turns off and you may unplug it from the USB charger and take it on the go.

Step 2: Charging the Internal Battery

USB Charger

or Computer

Micro USB Cable(included)

3.1 For iOS Users

Please go to the App Store and search for

“Stor-N-Go” or “Macally”, select and install

the Stor-N-Go app onto your iOS devices.

Stor-N-Go is a free application from the App Store for iOS devices and Google Play

Store for Android devices. For computer users, client applications “Stor-N-Go for Mac”

and “Stor-N-Go for Windows” are available to download on the Macally website. It

allows up to 5 devices to access the WIFISD2’s storage to wirelessly stream music,

videos, and photos simultaneously.

Step 3: Stor-N-Go App Download and Installation

*Note: iOS 6.0 and above is required.

3.3 For Mac OSX or Windows Users

The client software will connect the computer to the WIFISD2 wirelessly to

share files and stream multimedia content. Please download “Stor-N-Go for

Mac” or “Stor-N-Go for Windows” from http://us.macally.com/pages/drivers-

and-downloads. Install on your computer and run the file.

3.2 For Android Users

Please go to Google Play Store and search for

“Stor-N-Go” or “Macally”, select and install the

Stor-N-Go app onto your Android devices.

4.1 For iOS Users

Open Settings > and choose Wi-Fi option in your

device. Choose “WIFISD2-XXXX” from the available

network list and input the default password

“12345678”. Once the connection is established,

you will see “Connected” next to the network.

To use it as the Media Hub and Travel Router, do not connect the WIFISD2 to a

computer. Enable Wi-Fi mode by pressing the power button for 2 seconds and

wait for the Wi-Fi to boot up. The Wi-Fi LED should be a solid blue indicating that

Wi-Fi access is ready.

Step 4. Using the Media Hub and Travel Router

*Note: Android 3.0 and above is required.

Launch Stor-N-Go from your iOS device. Tap “File/Folder” on the bottom

and select “Stor-N-Go” on the bottom left of the next screen to view the

media on the WIFISD2 to stream. If files have been copied to the appropriate

subfolder in the “Share” Folder, you can access each type of media

(Documents, Photos, Music, Video) by pressing on the tiles on the home

page of the App. Please note that if files are not placed in this “Share” folder,

they will not appear if you click the media tiles on the home page.

4.2 For Android user

Open Settings > and choose Wi-Fi

option in your device. Choose

“WiFiSD2-XXXX” from the available

network list and input the default

password “12345678”. Once the

connection is established, you will

see “Connected” next to the network.

Launch Stor-N-Go from your iOS device. Tap “File/Folder” on the bottom and

select “Stor-N-Go” on the bottom left of the next screen to view the media on

the WIFISD2 to stream. If files have been copied to the appropriate subfolder

in the “Share” Folder, you can access each type of media (Documents, Photos,

Music, Video) by pressing on the tiles on the home page of the App. Please note

that if files are not placed in this “Share” folder, they will not appear if you click

the media tiles on the home page.

4.4 For Windows Users

Connect to the “WIFISD2-XXXX” under your network settings. The default password

is “12345678”. Verify in your Network and Sharing Center that the computer is

connected to WIFISD2-XXXX. Run “Stor-N-Go for Windows” and under the host

name, select WIFISD2. Click Login or My Storage and enter “admin” as the default

username and leave the password field blank.

4.3 For Mac OS X user

Click the Wi-Fi icon at the upper right corner

of your screen and select “WIFISD2-XXXX”,

then input the default password “12345678”

until you see the check mark. Run “Stor-N-Go

for Mac” application and under the host name

select the WIFISD2. Click Login or My Storage.

The default username is “admin” and leave

the password field blank.

Autres manuels pour WIFISD2

Table des matières

Autres manuels Macally Routeur réseau

Macally

Macally WIFISD2 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité