M-system M5XAMS Manuel utilisateur

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-2774 P. 1 / 4

INSTRUCTION MANUAL

TRACK/HOLD

(PC programmable) MODEL M5XAMS

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Signal conditioner ...............................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

The M5XAMS is programmable using the PC Conﬁgurator

Software. For detailed information on the PC conﬁguration,

refer to the M5CFG users manual. The M5CFG PC Con-

ﬁgurator Software is downloadable at M-System’s web site:

https://www.m-system.co.jp

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside a panel.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■POWER INPUT RATING & OPERATIONAL RANGE

• Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

24V DC rating: 24V ±10%, ≤ 1W

■GENERAL PRECAUTIONS

• Before you remove the unit or mount it, turn off the power

supply and input signal for safety.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -20 to +65°C

(-4 to +149°F) with relative humidity within 30 to 90%

RH in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

• Install lightning surge protectors for those wires connect-

ed to remote locations.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

COMPONENT IDENTIFICATION

TerminalCover

PowerIndicatorLED

ConﬁguratorJack

Body

Speciﬁcation

OutputSettingDIPSW

InputSettingDIPSW

(side)

M5XAMS

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-2774 P. 2 / 4

INSTALLATION

Set the unit so that its DIN rail adapter is at the bottom.

■MOUNTING THE UNIT ON A DIN RAIL

A)Hang the upper hook at the rear side of unit on the DIN

rail.

B)Push in the lower in keeping pressing the unit to the DIN

rail.

DIN rail

■REMOVING THE UNIT

A)Pull down the DIN rail adaptor using a minus screwdriv-

er.

B)Pull out the lower part of the unit.

C)Remove the upper part from the DIN rail.

Slider

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the connection diagram on the side of the unit.

■EXTERNAL DIMENSIONS unit: mm [inch]

94 [3.70]3 [.12]

25 [.98] 41 [1.61] (3.3 [.13])

• When mounting, no extra space is needed between units.

DIN RAIL

35mm wide

8–M3.5 SCREW

7.3 [.29]

■CONNECTION DIAGRAM

–

JACK

Configurator Jack

DC Current

Input (Z1)

–

OUTPUT

–

POWER

HOLD CONTROL

SWa

SWb

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.8 N·m

M5XAMS

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-2774 P. 3 / 4

EXTERNAL VIEWS

■LEFT VIEW ■FRONT VIEW

Output Setting

DIP SW Input Setting

DIP SW

SW1

Power Indicator LED

Configurator Jack

4SW2

■RIGHT VIEW

OUTPUT RANGING

The internal DIP switch setting is required to select I/O types before setting a precise I/O range using PC Conﬁgurator Soft-

ware (model: M5CFG).

For detailed information on the PC conﬁguration, refer to the M5CFG users manual.

Table 1. DIP switch settin: Input type

Input Type SW2

1234

0 – 50 mA DC ON OFF OFF OFF

-1000 – +1000 mV DC OFF ON OFF OFF

-10 – +10 V DC OFF OFF OFF OFF

Table 2. DIP switch setting: Output type

Output Type SW1

123456

0 – 20 mA DC ON OFF OFF OFF ON OFF

-5 – +5 V DC OFF ON ON OFF OFF ON

-10 – +10 V DC OFF ON OFF ON OFF ON

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Check DIP switch setting.

3) Power input voltage: Check voltage across the terminal

7 – 8 with a multimeter.

4) Input: Check that the input signal is within 0 – 100% of

the full-scale. When the output does not track the input

signal, check that the terminals 3 – 4 (shortcircuited or

open) is match to the setting.

5) Output: Check that the load resistance meets the de-

scribed speciﬁcations.

POWER INDICATOR LED

The transmitter is provided with a power indicator LED

which blinks in different patterns indicating various oper-

ating status.

The following ﬁgure indicates typical patterns.

LEDONOFFPATTERNSTRANSMITTERSTATUS

Downloadingthesetting

Rangesetting

Fineadjusting

Supplyingaﬁxedoutput

Normal

AbnormalOperation

(corruptionofconﬁgurationdata)

80ms

M5XAMS

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-2774 P. 4 / 4

MAINTENANCE

Regular calibration procedure is explained below:

■CALIBRATION

Warm up the unit for at least 10 minutes. Apply 0%, 25%,

50%, 75% and 100% input signal. Check that the output

signal for the respective input signal remains within accu-

racy described in the data sheet. When the output is out of

tolerance, recalibrate the unit using the PC Conﬁgurator

Software (model: M5CFG).

LIGHTNING SURGE PROTECTION

M-System offers a series of lightning surge protector for

protection against induced lightning surges. Please contact

M-System to choose appropriate models.

Autres manuels M-system Équipement de test

M-system

M-system Sentronic M5DY Series Manuel utilisateur

M-system

M-system Mini-M Series Manuel utilisateur

M-system

M-system Mini-M M2TG-14-M2 Manuel utilisateur

M-system

M-system Mini-M M2AMS2 Manuel utilisateur

M-system

M-system Mini-MW Series Manuel utilisateur

M-system

M-system Mini-M M2XF2 Manuel utilisateur

M-system

M-system Mini-M M2MLS Manuel utilisateur

M-system

M-system M6DPP Manuel utilisateur

M-system

M-system Mini-M Series Manuel utilisateur

M-system

M-system Sentronic Mini-M M2MS Series Manuel utilisateur

M-system

M-system W2PP Manuel utilisateur

M-system

M-system M2PA Series Manuel utilisateur

M-system

M-system Mini-M M2CDS Manuel utilisateur

M-system

M-system Mini-M M2LMS Manuel utilisateur

M-system

M-system MXCB-1 Manuel utilisateur

M-system

M-system Mini-M M2PHS2 Manuel utilisateur

M-system

M-system Mini-M M2VV Manuel utilisateur

M-system

M-system Sentronic Mini-M M2XPA3 Series Manuel utilisateur

M-system

M-system FDU Manuel utilisateur

M-system

M-system Mini-M M2MST Manuel utilisateur

M-system

M-system AD2LC Manuel utilisateur

M-system

M-system Mini-M M2PP Manuel utilisateur

M-system

M-system Sentronic Mini-M M2VF2 Series Manuel utilisateur

M-system

M-system Mini-M Series Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur