M-system R3S-YV4 Manuel utilisateur

R3S-YV4

P. 1 / 3EM-8940

DC VOLTAGE OUTPUT MODULE

(4 points, isolated) MODEL R3S-YV4

INSTRUCTION MANUAL

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

DC voltage output module ........................................... (1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■HOT INSERTION/REMOVAL OF MODULES

Removing or replacing modules does not affect other mod-

ules on the same backplane. It is possible to replace them

without removing the power supply. However, replacing

multiple modules at once may greatly change line voltage

levels. We recommend that you replace them one by one.

■ENVIRONMENT

•Indooruse

•Whenheavydustormetalparticlesarepresentintheair,

install the unit inside proper housing with sufﬁcient ven-

tilation.

•Donotinstalltheunitwhereitissubjectedtocontinuous

vibration.Donotsubjecttheunittophysicalimpact.

•Environmentaltemperaturemustbewithin-10to+55°C

(14to131°F)withrelativehumiditywithin30to90%RH

in order to ensure adequate life span and operation.

■WIRING

•Do not install cables (power supply, input and output)

close to noise sources (relay drive cable, high frequency

line, etc.).

•Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

The unit is designed to function as soon as power is sup-

plied,however,awarmupfor10minutesisrequiredforsat-

isfying complete performance described in the data sheet.

INSTALLATION

Use the Installation Base (model: R3-BSx).

R3S-YV4

P. 2 / 3EM-8940

■STATUS INDICATOR LED

RUN indicator:Bi-color(red/green)LED;

RedwhenthebusAoperatesnormally;

GreenwhenthebusBoperatesnormally;

Amber when both buses operate normally.

ERR indicator:GreenLEDturnsoninnormaloperating

conditions.

COMPONENT IDENTIFICATION

■SIDE DIP SW

• Output Range: SW1, SW2

OUTPUT 1 (SW1) OUTPUT 2 (SW1)

RANGE

OUTPUT 3 (SW2) OUTPUT 4 (SW2)

12345678

OFF OFF OFF OFF OFF OFF OFF OFF

-10–+10V(*)

ON OFF OFF OFF ON OFF OFF OFF

-5–+5V

OFF ON OFF OFF OFF ON OFF OFF

-1–+1V

ON ON OFF OFF ON ON OFF OFF

0–10V

OFF OFF ON OFF OFF OFF ON OFF

0–5V

ON OFF ON OFF ON OFF ON OFF

1–5V

OFF ON ON OFF OFF ON ON OFF

0–1V

• Output Hold: SW3

SW OUTPUT HOLD

HOLD (*)OFF

SW3-1 OFF ON

(*)Factorysetting

SW1SW2

SW3

■ FRONT VIEW ■ SIDE VIEW

ERR LED

RUN LED

Output

Hold

Output 2 (SW1)

Output 4 (SW2)

Range

Output 1 (SW1)

Output 3 (SW2)

Functions

■DIMENSIONS mm (inch)

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

130 (5.12)

27.5 (1.08) 109 (4.29)

120 (4.72)

POSITIONING

GUIDE

R3S-YV4

P. 3 / 3EM-8940

■CONNECTION DIAGRAM

M-SYSTEM WARRANTY

M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such

product was originally purchased if such product has been used under normal operating conditions and properly maintained, M-System’s sole liability, and purchaser’s exclusive

remedies, under this warranty are, at M-System’s option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this

warranty. To submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original

sales invoice.

THIS IS THE ONLY WARRANTY APPLICABLE TO M-SYSTEM PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. M-SYSTEM SHALL HAVE NO LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR

SPECIAL DAMAGES OF ANY KIND WHATSOEVER.

M-System Co., Ltd., 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN, Phone: (06) 6659-8201, Fax: (06) 6659-8510, E-mail: info@m-system.co.jp

*1. For dual redundant communication.

*2. To use shield line, connect it to SLD terminal and ground the terminal 20.

Note: Do not connect wide span and narrow span simultaneously within the same channel.

Do not use void terminals.

INTERNAL POWER

–

WIDE SPAN

NARROW SPAN

OUTPUT 1

–

WIDE SPAN

NARROW SPAN

OUTPUT 2

–

WIDE SPAN

NARROW SPAN

OUTPUT 3

–

WIDE SPAN

NARROW SPAN

OUTPUT 4

SLD

BUS A

BUS B*1

BUS CONNECTOR

WIRING INSTRUCTIONS

■APPLICABLE WIRE SIZE mm

• Solid: 0.2to1.0mm2(0.55to1.12dia.)

• Stranded:0.2to1.5mm2

(Tinning wire ends may cause contact failure and therefore

is not recommended.)

• Ferruled:

Unsheathed:0.25to1.5mm2

Sheathed:0.25to0.75mm2

•Exposewireconductorsby10mm(0.39”).

■CONNECTION PROCEDURE

Insert the wire end until it comes to a full stop while push-

ing slot with the tip of a screw driver as shown below. Be

sure wire insulation is not inside the terminal.

Screw Driver

Power wire

Stripped length

10mm

OUTPUT PIN ASSIGNMENT

PIN No. FUNCTION

OM1

3 VL1

4 SLD

OM2

7 VL2

8 SLD

10 NC

11 VH3

12 COM3

13 VL3

14 SLD

15 VH4

16 COM4

17 VL4

18 SLD

19 SLD

20 SLD

Autres manuels M-system Système d'E/S

M-system

M-system Devicenet R7F4DD-DA16B-C Manuel utilisateur

M-system

M-system R7D-SV4/UL Manuel utilisateur

M-system

M-system R3-SV4 Manuel utilisateur

M-system

M-system R30NE1 Manuel utilisateur

M-system

M-system R7C-YV2 Manuel utilisateur

M-system

M-system R3-SV4 Manuel utilisateur

M-system

M-system R7D-SV4 Manuel utilisateur

M-system

M-system R8-FS16N Manuel utilisateur

M-system

M-system R7ML-RS4 Manuel utilisateur

M-system

M-system R7 Series Manuel utilisateur

M-system

M-system R7G4HEIP-6-DC16A Manuel utilisateur

M-system

M-system R7D-DC8C Manuel utilisateur

M-system

M-system R7HL-PA4E Manuel utilisateur

M-system

M-system R7D-YV2A Manuel utilisateur

M-system

M-system R30SV4 Manuel utilisateur

M-system

M-system R7C-YV4 Manuel utilisateur

M-system

M-system R7M-DAC16C-R Manuel utilisateur

M-system

M-system R3-SV4C Manuel utilisateur

M-system

M-system R5T-PA2 Manuel utilisateur

M-system

M-system R7 Series Manuel utilisateur

M-system

M-system R7C-DC8C Manuel utilisateur

M-system

M-system R7C-EA16 Manuel utilisateur

M-system

M-system M5SN Manuel utilisateur

M-system

M-system R3-SV8N Manuel utilisateur

Manuels Système d'E/S populaires d'autres marques

WAGO

WAGO 750-344 Manuel utilisateur

Teknim

Teknim TWM-1887 Mode d’emploi

Intelligent Appliance

Intelligent Appliance IA-2662-E Manuel utilisateur

BERGHOF

BERGHOF ECC DIO 16/16 Mode d’emploi

Advantech

Advantech PCM-27J3AU Manuel d'installation et d'exploitation

Festo

Festo CP-E08-M12-CL Manuel utilisateur

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manuel utilisateur

Hitachi

Hitachi HX-RIO3 Series Manuel utilisateur

NUUO

NUUO SCB-A08 Manuel utilisateur

jablotron

jablotron JB-110N Manuel utilisateur

Omron

Omron SYSMAC C200H Manuel utilisateur

DOLD

DOLD SAFEMASTER M Manuel utilisateur

ABB

ABB OPT-MF-001 Manuel utilisateur

Omron

Omron SYSMAC C2000H Manuel utilisateur

Helmholz

Helmholz TB20 Manuel utilisateur

ICP DAS USA

ICP DAS USA tM-AD2 Manuel utilisateur

Automationdirect.com

Automationdirect.com DL305 Manuel utilisateur

WAGO

WAGO I/O-SYSTEM 750 Manuel utilisateur