M-system R3-CZ4 Manuel utilisateur

R3-CZ4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax:

+81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8447 Rev.2 P. 1 / 3

ZERO-PHASE CURRENT INPUT MODULE

(with noise lter)

MODEL R3-CZ4

INSTRUCTION MANUAL

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

the contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

CT input module.............................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the side of the product to be

exactly what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■HOT INSERTION/REMOVAL OF MODULES

•Removing or replacing modules does not affect other mod-

ules on the same backplane. It is possible to replace them

without removing the power supply. However, replacing

multiple modules at once may greatly change line voltage

levels. We recommend that you replace them one by one.

■ENVIRONMENT

•Indoor use

•When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

•Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

•Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

•Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

•Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

•The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

INSTALLATION

Use the Installation Base (model: R3-BSx).

R3-CZ4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax:

+81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8447 Rev.2 P. 2 / 3

COMPONENT IDENTIFICATION

SW1SW2

SW3

■ FRONT VIEW ■SIDE VIEW

ERR LED

RUN LED

Conv.

Rate

Input 2 (SW1)

Input 4 (SW2)

Range

Input 1 (SW1)

Input 3 (SW2)

Functions

■STATUS INDICATOR LED

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

Green when the bus B operates normally;

Amber when both buses operate normally.

ERR indicator: Bi-color (red/green) LED;

Red with the input abnormality;

Green in normal operating conditions.

■SIDE DIP SW

• Input Range: SW1, SW2

INPUT 1 (SW 1) INPUT 2 (SW 1)

RANGEINPUT 3 (SW 2) INPUT 4 (SW 2)

12345678

OFF OFF OFF OFF OFF OFF OFF OFF

0 – 1.5mA (*)

OFF OFF OFF

0 – 0.1mA

• Conversion Rate: SW3

SW CONVERSION RATE

80 ms (*)40 ms 20 ms 10 ms

SW3-1 OFF ON OFF ON

SW3-2 OFF OFF ON ON

(*) Factory setting

Note: Be sure to set unused SW3-3 and 3-4 to OFF.

PC CONFIGURATOR

The following parameters can be set with using PC Conﬁgurator Software (model: R3CON):

•0% scaling value

•100% scaling value

•0% adjustment value (bias)

•100% adjustment value (gain)

•0% input value

•100% input value

•Disable the unused channel

R3-CZ4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax:

+81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8447 Rev.2 P. 3 / 3

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■DIMENSIONS mm (inch)

130 (5.12)

27.5 (1.08) 109 (4.29)

7.9 (.31)

POSITIONING

GUIDE

TERMINAL

COVER

10–M3.5

SCREW

■CONNECTION DIAGRAM

BUS CONNECTOR

INTERNAL POWER

INTERNAL

BUS A

INTERNAL

BUS B*

*For dual redundant communication.

INPUT 1

LOAD

SOURCE

ZCT

INPUT 2

LOAD

SOURCE

ZCT

INPUT 3

LOAD

SOURCE

ZCT

INPUT 4

LOAD

SOURCE

ZCT

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.5 N·m

■SOLDERLESS TERMINAL mm (inch)

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable. Solder-

less terminals with insulation sleeve do not ﬁt.

Applicable wire size: 0.3 – 0.75 mm2

3.2 (.13) dia.

4 min.

(.16)

12 (.47) max.

6 max.

(.24)

3 (.12) max.

Autres manuels M-system Système d'E/S

M-system

M-system R3-DA64A Manuel utilisateur

M-system

M-system R3-SV8N Manuel utilisateur

M-system

M-system R3Y-DC16 Manuel utilisateur

M-system

M-system R5T-RS Manuel utilisateur

M-system

M-system R30SV2 Manuel utilisateur

M-system

M-system R7D-RS4 Manuel utilisateur

M-system

M-system R3Y-RS8 Manuel utilisateur

M-system

M-system R7M-DC4G-R Manuel utilisateur

M-system

M-system R30YN16C Manuel utilisateur

M-system

M-system R7 Series Manuel utilisateur

M-system

M-system R7M-EA8/UL Manuel utilisateur

M-system

M-system Devicenet R7F4DD-DA16A-C Manuel utilisateur

M-system

M-system R7D-YV2A Manuel utilisateur

M-system

M-system R3-PC16A Manuel utilisateur

M-system

M-system R7I4DML3-DC32A Manuel utilisateur

M-system

M-system R7C-EC16B Manuel utilisateur

M-system

M-system R7 Series Manuel utilisateur

M-system

M-system Devicenet R7F4DD-DAC16C-H Manuel utilisateur

M-system

M-system R7F4DC-DC16A-H Manuel utilisateur

M-system

M-system R7ML-LC2-R Manuel utilisateur

M-system

M-system R7F4DC-DA16A-J Manuel utilisateur

M-system

M-system R3-SV4A Manuel utilisateur

M-system

M-system M8BS2-041 Manuel utilisateur

M-system

M-system R3-SV8N Manuel utilisateur

Manuels Système d'E/S populaires d'autres marques

WAGO

WAGO 750-344 Manuel utilisateur

Teknim

Teknim TWM-1887 Mode d’emploi

Intelligent Appliance

Intelligent Appliance IA-2662-E Manuel utilisateur

BERGHOF

BERGHOF ECC DIO 16/16 Mode d’emploi

Advantech

Advantech PCM-27J3AU Manuel d'installation et d'exploitation

Festo

Festo CP-E08-M12-CL Manuel utilisateur

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manuel utilisateur

Hitachi

Hitachi HX-RIO3 Series Manuel utilisateur

NUUO

NUUO SCB-A08 Manuel utilisateur

jablotron

jablotron JB-110N Manuel utilisateur

Omron

Omron SYSMAC C200H Manuel utilisateur

DOLD

DOLD SAFEMASTER M Manuel utilisateur

ABB

ABB OPT-MF-001 Manuel utilisateur

Omron

Omron SYSMAC C2000H Manuel utilisateur

Helmholz

Helmholz TB20 Manuel utilisateur

ICP DAS USA

ICP DAS USA tM-AD2 Manuel utilisateur

Automationdirect.com

Automationdirect.com DL305 Manuel utilisateur

WAGO

WAGO I/O-SYSTEM 750 Manuel utilisateur