Lund Genesis Manuel utilisateur
Page 1 of 7
Installation Instructions
Important Safety Information
•Serious personal injury and property damage can occur if vehicle is driven without both black buckles at the front of cover fastened. ans les
•Prior to vehicle operation, clamps must be secured such that the clamp lips tightly grip the inner bedwall structure.
•Only release buckles when fully installing cover.
•After a setting period (1 week) it may be necessary to readjust the clamp load after foam isolators take a set to maintain the uniform gap
between the Genesis™ Tri-Fold Tonneau cover and bed rails.
•Check the bracket clamp loads every 3 months or 5,000 miles.
•The Genesis™ Tri-Fold Tonneau cover must be closed or secured with straps while the vehicle is in motion.
For proper installation and best possible fit, please read all instructions BEFORE you begin.
NOTE: Actual product may vary from illustration.
Tri-Fold Cover Assembly
4 x Adapter
Hardware maybe packed in tube dun age. Check dun age for hardware before discarding.
2 x Foam
Mousse
Contents
A B
C
Genesis™and Genesis Elite™Tri-Fold Tonneau Cover
Page 2 of 7
Car Wash Supplies Clean Towel
Tools Required
Preparation Before Installation
•Wash the upper rail surfaces of the truck bed.
•Be sure to completely dry the washed surfaces before installing the tonneau cover.
Installation Steps NOTE: Actual application may vary slightly from illustrations.
1
1A Make sure there is no dust or debris on the front rail. Turn
cover over, apply supplied foam (Item B) to front rail of
cover (Item A). Flip cover over and place on truck as shown
in step 1B, then proceed to Step 2.
1B Place the cover assembly on the top of the truck bed next to the cab.
cover
A
B
Installation Steps
2
3
Page 3 of 7
4
NOTE: Actual application may vary slightly from illustrations.
Line up to front of bed first. Center the cover assembly on the truck.
Position the cover assembly so the gaps on all sides are equal.
=
cover
Approx 1/4” at both corners
Remove plastic caps from the ends of the channels on both sides of the vehicle. Push tab in while sliding out.
A
C
C
Insert 2 adaptors (Item C) into each bed sidewall track. Slide one adaptor in each track forward until they are centered with
both front cover clamps (Item A). Re-install caps removed in Step 3.
A
A
B
.
Installation Steps
5
Page 4 of 7
6
7
NOTE: Actual application may vary slightly from illustrations.
Secure both front clamps.
Warning: Prior to vehicle operation, inspect clamps to make sure the lip on clamp is properly seated in the utility track adaptors.
7A Unfold second section of the cover
7B Make sure there is no dust or debris on the rear rail. Apply supplied foam (Item B) to the rear rail of cover (Item A).
7C Unfold third section of the cover.
A
Tighten
Loosen
•
•
A
C
A
C
A
C
Slide clamps to edge of truck bed.
Rotate clamps down from its storage position.
Adjust clamps to proper height.
Rotate clamps to locking position.
Repeat for opposite side.
Note: Repeat steps for rear clamps.
The cover has retaining straps with quick-release
buckles to keep it from being damaged when bulk
hauling or when it is not on the vehicle.
cover
cover
9
11
12
10
8
Page 5 of 7
Installation Steps NOTE: Actual application may vary slightly from illustrations.
Securing Both Rear Clamps
NOTE: Clamp handle must rotate completely down to
the stop to be locked. If something interfers with
the handle (bed liner, bed extender or cargo, etc.)
it must be modified or removed.
cover bow
Rotate each clamp down from its storage position.
12
4
cover
•Raise to Tighten (Up)
•Lower to Loosen (Down)
Adjust clamps to proper height. Make sure that the inner bedwall structure and clamp lid are
aligned as shown by dashed line. Handle height should be adjusted, such that, the clamp
contacts the bed rail flange while the handle is in the 4 o’ clock (LH) or 8 o’clock (RH) position.
1
2bow
Rotate handles back up and slide clamps to edge of truck bed as shown. For ease
of sliding outward, the latch handle should be in this position until the clamp
engages the bed flange.
Reverse process for folding and stowing cover.
Rotate clamps to locking position. Repeat for opposite side. Note: A light to moderate
force should be felt when latching to the truck bed. The latches should NOT be loose
when in the LOCKED POSITION.
Reverse process for folding and stowing cover.
3
56789
12345
45678
13
14
15
After clamping Tonneau inspect clamps to make sure the pinch weld is seated properly in the notch on the clamp. Trim the bed
cap at the clamp location if it extends down past the metal.
If traveling with the Tonneau in the folded position it is recommended to use a safety pin or lock in the front clamps.
Rotate clamp up from its install position into its storage position as shown.
Make sure that latch handle matches illustration on bow caution label.
Bed Cap
cover
Repeat Step 11 thru Step 14 Front Driver Side Clamp
cover
cover
1/4” Safety Pin / Lock Hole
Pinch Weld
Clamp Notch
Outside sheet metal
Securing Front Clamps - Fold Cover Forward
Unlatching and Securing Latches for Folding and Stowing Center
Installation Steps NOTE: Actual application may vary slightly from illustrations.
Page 6 of 7
Page 7 of 7
Care and Cleaning
•Wash only with mild soap & dry with a clean cloth.
•Avoid the use of automatic “brush-syle” car washes.
•Do not use cleaning solvents of any kind.
•Pressure car washes are okay as long as you hold the wand no closer than two feet from the cover.
•We recommend the same quality products normally used for vinyl tops to keep the cover clean. When using a protectant, be
sure that it is water based.
Congratulations!
You have purchased one of the many quality Lund®branded products offered by Lund International, Inc. We take the utmost pride in
our products and want you to enjoy years of satisfaction from your investment. We have made every effort to ensure that your product
is top quality in terms of fit, durability, finish and ease of installation.
cover
cover
When traveling with tonneau in the folded
position the two rear clamps must be in there
storage position so the latch handles do not
puncture the cover and void the warranty.
The retaining straps must be buckled when vehicle is in motion if Tonneau is in the folded position.
16
Installation Steps NOTE: Actual application may vary slightly from illustrations.
Autres manuels pour Genesis
4
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Lund Accessoires automobiles
Lund
Lund Genesis Manuel utilisateur
Lund
Lund Genesis Manuel utilisateur
Lund
Lund 84058 Manuel utilisateur
Lund
Lund Cargo Carrier Manuel utilisateur
Lund
Lund Step Rails 2710 Series Manuel utilisateur
Lund
Lund Interceptor Manuel utilisateur
Lund
Lund Interceptor Manuel utilisateur
Lund
Lund 84117 Manuel utilisateur
Lund
Lund AVS Bugflector Manuel utilisateur
Lund
Lund 84127 Manuel utilisateur
Lund
Lund REVELATION Manuel utilisateur
Lund
Lund 22660986 Manuel utilisateur
Lund
Lund 82991 Manuel utilisateur
Lund
Lund SR2 Manuel utilisateur
Lund
Lund Rampage Products Ventvisor Manuel utilisateur
Lund
Lund TrailRunner Diamond Plate 2612 Series Manuel utilisateur
Lund
Lund REVOLUTION BULL BAR Manuel utilisateur
Lund
Lund AVS Ventvisor Manuel utilisateur
Lund
Lund SR2 Manuel utilisateur
Lund
Lund Genesis Manuel utilisateur
