Lumel N10A Manuel utilisateur
1
POWER NETWORK
PARAMETER
ANALYSER
N10A
SERVICE MANUAL
2
3
POWER NETWORK PARAMETER ANALYSER - N10A
SERVICE MANUAL
CONTENTS
1. APPLICATION................................................................................. 5
2. METER SET.................................................................................... 6
3. INSTALLATION............................................................................... 6
3.1. FITTING................................................................................... 6
3.2. EXTERNAL CONNECTION DIAGRAMS ................................ 8
4. PROGRAMMING .......................................................................... 13
4.1. FACEPLATE DESCRIPTION.................................................. 13
4.2. N10A OPERATING MODES................................................... 14
4.2.1 MEASURING MODE...................................................... 15
4.2.1.1. Measurement of voltage and current harmonics........ 16
4.2.2. TIME SETTING MODE - t ............................................. 17
4.2.3. PARAMETER CONFIGURATION MODE - S................ 17
4.2.4. ALARM CONFIGURATION MODE - A .......................... 19
4.2.5. PAGE CONFIGURATION MODE - P ........................... 19
5. ERROR CODES............................................................................ 25
6. TECHNICAL DATA ....................................................................... 25
7. ORDERING CODES ..................................................................... 29
8. MAINTENANCE AND WARRANTY.............................................. 30
March 2007 - KZ 1268/06
4
5
1. APPLICATIONS
The N10A type meter is a programmable digital instrument destined to measure
parameters in three-phase three-wire or four-wire power networks, in symmetric
and asymmetric systems. The N10A meter is a version of the N10 meter, in which
3 bi-directional analog outputs have been added for customers’ needs.
The N10A meter enables the display of measured and calculated quantities (196 in
all), the digital transmission of their values and the conversion into three bi-directional
analog output signals.
Internal current and voltage transformers ensure the galvanic separation of mea-
sured channels.
The N10A meter ensure the measurement of: RMS voltage and current, active, re-
active and apparent power, active reactive and apparent energy, power coefficients,
frequency, 15-minute average active power.
Voltages and currents are multiplied by voltage and current ratios of measuring
transducers what is taking in consideration in calculations and indications of power
and energy. The meter shows also the real time.
The RS-485 interface enables the communication with the master system.
Other communication protocols can be realised through the external converter, e.g.
the PD7 type with MODBUS/PROFIBUS.
One of the important feature is the possibility to perform the programmed selection
of 3 quantities which are converted into bi-directional current signals on 3 analog
outputs of the meter.
The relay output can serve to signal the overflow of the chosen quantity threshold.
Measurements are carried out by the sampling method of the voltage and current
signal.
The meter is adapted to be fixed in a panel by means of holders.
Differences between N10 and N10A meters
N10 N10A
Analog outputs 1 output 0...20 mA (4...20 mA)
accuracy 0.5%
3 outputs ± 5 mA (0...5 mA)
accuracy 0.2 %
Relay outputs
Impulse passive
outputs
Impulse passive
input
3 relays 1 relay
none1 output
1 input none
6
2. METER SET
The set includes:
- N10A type meter 1 pc.
- service manual 1 pc.
- warranty card 1 pc.
- holders to fix into a pannel 4 pcs.
Additionally for the execution with interface:
- service manual of the serial interface 1 pc.
- lead of the RS-485 interface 1 pc.
- matching resistor 1 pc.
- diskette for the WIZPAR program 1 pc.
3. INSTALLATION
3.1. Fitting way
The meter is adapted to be mounted by means of holders according fig.1.
The meter housing is made of a sell-extinguishing plastics.
Housing dimensions are 144x144x77mm. At the rear side of the meter there are
terminal strips which enable the connection of 2.5 mm2external leads.
7
Fig.1 Overall dimensions and fitting way of the N10A meter.
8
3.2. External connection diagrams
Direct measurement in a 3-phase network
Half-intermediate measurement in a 3-phase network
9
Fig. 2. Meter connection diagrams in a three-phase network
Intermediate measurement using 2-current transformers and 2 or 3 voltage trans-
formers in a 3-phase network
10
Direct measurement in a 4-wire network
Half-intermediate measurement in a 4-wire network
Table des matières
Autres manuels Lumel Instrument de mesure
Lumel
Lumel N30P Manuel utilisateur
Lumel
Lumel ND20CT Manuel utilisateur
Lumel
Lumel N32O Manuel utilisateur
Lumel
Lumel NR30IoT Manuel utilisateur
Lumel
Lumel ND08 Manuel utilisateur
Lumel
Lumel N20PLUS Manuel utilisateur
Lumel
Lumel N10 Manuel utilisateur
Lumel
Lumel NMID30-2 Manuel utilisateur
Lumel
Lumel N21 Manuel utilisateur
Lumel
Lumel ND20CT Manuel utilisateur
Lumel
Lumel N30U Manuel utilisateur
Lumel
Lumel N30O Manuel utilisateur
Lumel
Lumel NA6 Manuel utilisateur
Lumel
Lumel ND10 TYPE Manuel utilisateur
Lumel
Lumel N27P Manuel utilisateur
Lumel
Lumel N30H Manuel utilisateur
Lumel
Lumel N14 Manuel utilisateur
Lumel
Lumel N43 Manuel utilisateur
Lumel
Lumel N20 Manuel utilisateur
Lumel
Lumel NR30PNET Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur