LSIS XGT Series Manuel utilisateur

Right choice for ultimate yield

LSIS strives to maximize customers' profit in gratitude of choosing us for your partner.

Programmable Logic Controller

Sequence of Events Input Module

User’s Manual



Read this manual carefully before

installing,

wiring, operating, servicing

or inspecting this equipment.



Keep this manual within easy reach

for quick reference.

XGF-SOEA

XGT Series

http://eng.lsis.biz

Safety Instructions

Safety Instructions should always be observed in order to prevent accident

or risk with the safe and proper use the product…

Instructions are separated into “Danger”, “Warning” and “Caution”, and

the meaning of the terms is as follows;

■

The marks displayed on the product and in the user’s manual have the following meanings.

This mark is to call a user's attention to actions and operations which may cause

dangerous situation. Instructions with this mark shall be carefully read and observed

to keep from dangerous situation.

This mark is to call a user's attention to possibility of electric shock under the

special conditions.

This symbol indicates that serious injury or death may be

caused in a moment if some applicable instructions are

violated.

This symbol indicates the possibility of serious injury or

death if some applicable instructions are violated.

This symbol indicates the possibility of slight injury or

damage to products if some applicable instructions are

violated.

Danger

Warning

Caution

■Safety Instructions when designing

■Safety Instructions when installing

■Safety Instructions when wiring

 Surely use the ground wire of Class 3 for FG terminals, which is exclusively used for PLC. If the

terminals not grounded correctly, abnormal operation may be caused.

 Prior to wiring and connection in PLC, check the rated voltage and terminal arrangement of the

product. If other power than rated is connected or wiring is incorrect, it may cause fire or defect.

 Secure the screws of terminals tightly with specified torque when wiring. If the screws of terminals

get loose, short circuit or abnormal operation may be caused.

 Don’t let any foreign materials such as wiring waste inside the module

Caution

 Use PLC only in the environment specified in general standard. If not, electric shock, fire,

abnormal operation of the product or flames may be caused.

 Be sure that the module is correctly secured. If the module is not installed correctly, abnormal

operation, error or dropping may be caused.

Caution

 I/O signal or communication line shall be designed at least 100mm

away from a hi gh-voltage cable or power line to be kept from influence of noise or magnetic

field changing . If not, it may cause abnormal operation.

 Let the product installed free from direct vibration if lots of vibration is expected.

 Be sure to install the product free from metallic dust which may cause abnormal operation if

lots metallic dust is expected.

Caution

■Safety Instructions for test-operation or repair

■Safety Instructions for waste disposal



Don’t remove PCB from the module case nor remodel the module. Defect, abnormal operation,

product damage or fire may occur. Prior to installing or disassembling the module, let the power off.

The battery shall be exchanged only when the power is On. If it is exchanged while the power is

Off, the program may be lost.

Caution



Product waste shall be processed as industrial waste.

Caution

 Don’t touch the terminal when powered. Abnormal operation or electric shock may occur.

 Prior to cleaning or tightening the terminal screws, let the power off.

Warning

Revision History

Version Date Remark Revised position

V 1.0 ’13.09 First Edition -

※The number of User’s manual is indicated right part of the back cover.

About User’s Manual

Thank you for purchasing PLC of LSIS Co.,Ltd.

Before use, make sure to carefully read and understand the User’s Manual about the functions, performances, installation and

programming of the product you purchased in order for correct use and importantly, let the end user and maintenance

administrator to be provided with the User’s Manual.

The User’s Manual describes the product. If necessary, you may refer to the following description and order accordingly. In

addition, you may connect our website (http://eng.lsis.biz/) and download the information as a PDF file.

Relevant User’s Manuals

Title Description

XG5000 User’s Manual

(for XGK, XGB)

XG5000 software user manual describing online function such as

programming, print, monitoring, debugging by using XGK, XGB

CPU

XG5000 User’s Manual

(for XGI, XGR)

XG5000 software user manual describing online function such

as programming, print, monitoring, debugging by using XGI,

XGR CPU

XGK/XGB Instructions & Programming

User’s Manual

User’s manual for programming

to explain how to use

instructions that are used PLC system with XGK, XGB CPU.

XGI/XGR/XEC Instructions & Programming

User’s Manual

User’s manual for programming

to explain how to use

instructions that are used PLC system with XGI, XGR,XEC CPU.

XGK CPU User’s Manual

(XGK-CPUA/CPUE/CPUH/CPUS/CPUU)

XGK-CPUA/CPUE/CPUH/CPUS/CPUU user manual describing

about XGK CPU module, power module, base, IO module,

specification of extension cable and system configuration, EMC

standard

XGI CPU User’s Manual

(XGI-CPUU/CPUH/CPUS)

XGI-CPUU/CPUH/CPUS user manual describing about XGI

CPU module, power module, base, IO module, specification of

extension cable and system configuration, EMC standard

XGR redundant series User’s

Manual

XGR- CPUH/F, CPUH/T user manual describing about XGR

CPU module, power module, extension drive, base, IO module,

specification of extension cable and system configuration, EMC

standard

Current XGF-SOEA manual is written based on the following version.

Related OS version list

Product name OS version

XGK-CPUH, CPUS, CPUA, CPUE, CPUU V4.2

XGI-CPUU, CPUH, CPUS V3.8

XGR-CPUH/F, CPUH/T V2.5

XG5000(XG-PM) V3.68

◎Contents ◎

Chapter 1 Introduction ……………………………………………………… 1-1 ~ 1-9

1.1 How to use the manual ……………………………………………………… 1-1

1.2 Introduction of the module …………………………………………………… 1-2

1.3 Names and functions of each part ………………………………………… 1-3

1.4 Features of the module …………………………………………………… 1-4

1.5 How to install the module …………………………………………………… 1-5

1.5.1 How to install the module …………………………………………………………………… 1-5

1.5.2 Separation of the module …………………………………………………………………… 1-6

1.6 Differences with DC input module ………………………………………… 1-7

1.7 Glossary ………………………………………………………………………… 1-9

Chapter 2 Specifications …………………………………………………… 2-1 ~ 2-8

2.1 General Specifications ……………………………………………………… 2-1

2.2 Performance Specifications ………………………………………………… 2-2

2.3 Circuit system of the terminal block ……………………………………… 2-3

2.4 Key functions

………………………………………………………………… 2-4

2.4.1 Setting the SOE’s functions and operations ……………………………………………… 2-4

2.4.2 Display functions and Diagnosis …………………………………………………………… 2-9

2.4.3 External time format(IRIG-B) ………………………………………………………………… 2-5

2.4.4 Signal process ……………………………………………………………………………… 2-8

Chapter 3 Installation and Wiring …………………………………………… 3-1 ~ 3-4

3.1 Installation ……………………………………………………………………… 3-1

3.1.1 Installation environment …………………………………………………………………… 3-1

3.1.2 Precautions on handling ……………………………………………………………………… 3-1

3.2 Wiring …………………………………………………………………………… 3-2

3.2.1 Precautions on wiring ………………………………………………………………………… 3-2

3.3 Wiring of DC 24V ……………………………………………………………… 3-3

3.3.1 Specifications for power supply ……………………………………………………………… 3-3

3.4 Using the external time information ……………………………………… 3-4

3.4.1 In case of using the external time …………………………………………………………… 3-4

Chapter 4 Operation Setting and Monitor ………………………………… 4-1 ~ 4-26

4.1 Operation Setting and Monitor ……………………………………………… 4-1

4.2 Setting the basic parameters ………………………………………………… 4-2

4.2.1 Setting items ………………………………………………………………………………… 4-2

4.2.2 How to set the basic parameters …………………………………………………………… 4-2

4.3 Setting I/O parameters ………………………………………………………… 4-4

4.3.1 How to use I/O parameters ………………………………………………………………… 4-4

4.3.2 I/O parameters setting screen ……………………………………………………………… 4-4

4.3.3 SOE operations setting screen …………………………………………………………… 4-5

4.4 Monitoring and event history display …………………………………… 4-11

4.4.1 Monitoring screen ……………………………………………………………………… 4-11

4.4.2 SOE monitor screen …………………………………………………………………… 4-13

4.5 Save as excel file …………………………………………………………… 4-22

4.5.1 Save as Excel file …………………………………………………………………………… 4-22

4.6 Automatic Registration of U Device ……………………………………… 4-24

4.6.1 Automatic registration of U device ……………………………………………………… 4-24

4.6.2 Save variables ……………………………………………………………………………… 4-26

Chapter 5 Function setting………………………………………..…………… 5-1 ~ 5-9

5.1 SOE Functions ………………………………………………………………… 5-1

5.1.1 SOE Functions ………………………………………………………………………………… 5-1

5.2 Setting event history ……………………………………..…………………… 5-2

5.2.1 Setting items ………………………………………………………………………………… 5-2

5.3 Setting event conditions …………………………………………………… 5-4

5.3.1 Setting items ………………………………………………………………………………… 5-4

5.4 Setting input filter …………………………………………………………… 5-5

5.4.1 Setting items …………………………………………………………………………………… 5-5

5.4.2 Example of setting the input filter ………………………………………………………… 5-6

5.5 Setting chattering detection ………………………………………………… 5-7

5.5.1 Setting items ………………………………………………………………………………… 5-7

5.5.2 Example of operation the chatter detection function ……………………………………… 5-7

5.6 Setting external time ………………………………………………………… 5-9

5.6.1 Setting items ………………………………………………………………………………… 5-9

Chapter 6 Instruction ………………………………………………………… 6-1 ~ 6-19

6.1 Descriptions on the instruction(XGR/XGI) ………………………………… 6-1

6.1.1 SOE_RD……………………………………………………………………………………… 6-1

6.1.2 SOE_M_RD …………………………………………………………………………………… 6-5

6.1.3 SOE_C_CLR ………………………………………………………………………………… 6-7

6.1.4 SOE_M_CLR ………………………………………………………………………………… 6-8

6.2 Descriptions on the instruction(XGK) ……………………………………… 6-9

6.2.1 SOERD……………………………………………………………………………………… 6-9

6.2.2 SOEMRD……………………………………………………………………………………… 6-11

6.2.3 SOCCLR……………………………………………………………………………………… 6-13

6.2.4 SOEMCLR…………………………………………………………………………………… 6-14

6.3 Description on SOE data ………………………………………………… 6-15

Chapter 7 Troubleshooting …………………………………………………… 7-1 ~ 7-5

7.1 Troubleshooting ……………………………………………………………… 7-1

7.1.1 Checking the SOE module state through the XG5000’s system monitor ……………… 7-1

7.1.2 In case the state LED flashes(1 second cycle) …………………………………………… 7-2

7.1.3 In case the state LED flashes(0.2 second cycle) ………………………………………… 7-3

7.1.4 In case the state is turned off LED ……………………………………………………… 7-3

7.1.5 In case the input LED is not turned on ……………………………………………………… 7-4

7.1.6 In case the event is not recorded ………………………………………………………… 7-5

Appendix …………………………………………………………………… App.1~App.1

Appendix 1 Dimension ……………………………………………………………………… Appendix 1-1

Chap. 1 Introduction

1 - １

Chap. 1 Introduction

1.1 How to use the manual

To make the program, please refer to this manual with the XG5000 software manual.

The CPU O/S and XG5000 of the below version or later should be applied to the XGF-SOEA module. The

manual is based on the below version.

 XG5000 programming tool(Tool): Ver 3.68

 XGK CPU series: Ver 4.20

 XGI CPU series: Ver 3.80

 XGR CPUH: Ver 2.50

Autres manuels pour XGT Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels LSIS Système d'E/S

LSIS

LSIS XGT Series Manuel utilisateur

Manuels Système d'E/S populaires d'autres marques

WAGO

WAGO 750-344 Manuel utilisateur

Teknim

Teknim TWM-1887 Mode d’emploi

Intelligent Appliance

Intelligent Appliance IA-2662-E Manuel utilisateur

BERGHOF

BERGHOF ECC DIO 16/16 Mode d’emploi

Advantech

Advantech PCM-27J3AU Manuel d'installation et d'exploitation

Festo

Festo CP-E08-M12-CL Manuel utilisateur

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manuel utilisateur

Hitachi

Hitachi HX-RIO3 Series Manuel utilisateur

NUUO

NUUO SCB-A08 Manuel utilisateur

M-system

M-system R3Y-RS8 Manuel utilisateur

jablotron

jablotron JB-110N Manuel utilisateur

Omron

Omron SYSMAC C200H Manuel utilisateur

DOLD

DOLD SAFEMASTER M Manuel utilisateur

ABB

ABB OPT-MF-001 Manuel utilisateur

Omron

Omron SYSMAC C2000H Manuel utilisateur

Helmholz

Helmholz TB20 Manuel utilisateur

ICP DAS USA

ICP DAS USA tM-AD2 Manuel utilisateur

Automationdirect.com

Automationdirect.com DL305 Manuel utilisateur