Look E Post 2 Evo Manuel utilisateur

NUAL

Congratulations!

You have selected a LOOK accessory.

We thank you for your conﬁdence in our products.

By choosing this LOOK accessory, you get a high-tech product, designed in France. Like the

vast majority of LOOK products, it is identical to those supplied to major professional teams,

and undergoes regular quality-control checks throughout its manufacturing process to assure

your total satisfaction.

Our products comply with current and various European and international standards.

LOOK products are protected by industrial property rights. For more information, go to:

www.lookcycle.com/patents

Warning:

- This LOOK product is designed and optimized to be used by cyclists not exceeding

100 kg (220.5 lbs.)

- If you weigh more than 85 kg (187 lbs.), you must be especially vigilant and have it

inspected more frequently (than someone weighing less than 85 kg/187 lbs.) to search for

any cracks, deformations, or any other signs of fatigue or stress.

The life span of LOOK components depends on many factors, such as how it is used and the

morphology of the cyclist. Impacts, falls, improper use, or any sudden impact in general, may

compromise the structural integrity of the components and signiﬁcantly reduce their life

expectancy.

Some components are also subject to wear over time. Have your bicycle inspected regularly

by an authorized LOOK retailer to verify the absence of cracks, deformations of any kind, and/

or signs of fatigue or wear. If an inspection reveals any deformations, cracks, signs of impact

or stress marks, even minor in appearance, immediately replace the component in question;

components that have experienced excessive wear must also be immediately replaced. The

frequency of inspection depends on many factors. See your authorized LOOK dealer. The

components to be replaced must be done so by an authorized LOOK retailer.

The list of replaceable components is available at any authorized LOOK retailer.

LIFE SPAN - WEAR - INSPECTION REQUIRED

Cycling is a dangerous activity by nature. To reduce the risk of injury, be sure to maintain your

bicycle properly, and install and adjust all components correctly. While practicing the sport

of cycling, always wear a helmet and know and respect the rules of the road. Beware of the

dangers of the road and trafﬁc. Learn about the laws currently in force in the country where you

are located. If you ride at night, it is not enough to see, but vital to be seen by others. Standard

reﬂectors are not sufﬁcient and cannot replace quality front and rear lights. Wearing reﬂective

clothing is strongly recommended and potentially mandatory in some areas or countries.

PLEASE READ CAREFULLY BEFORE USING!

Before use, read the instructions thoroughly, and follow the advice given, in order to take full

advantage of the features of this high-quality product.

LOOK reserves the right to change product speciﬁcations without prior notice for the

purposes of improving it.

The E-Post is the concept of an integrated seat post, patented by LOOK, that allows the seat

post to be supported by the seat tube of the frame. There is, therefore, no risk of the post

slipping into the frame. Anti-rotation is ensured by the non-circular shape of the post and seat

tube.

The concept incorporates an elastomer sleeve that ensures the ﬁltration of vibrations,

increasing comfort when riding the bicycle.

The E-Post 2 EVO offers a setback of -15 mm. This model is not reversible. It is compatible with

the standard Selle Italia Monolink® saddle via an optional adapter kit.

The E-Post 2 EVO is only compatible with the LOOK 795 bicycle.

PRODUCT OVERVIEW

EXPLODED VIEW OF THE E-POST 2 EVO SEATPOST

1: The E-POST 2 - carbon body

2: Screw ﬁxation shell

3. Set Screw

4: Elastomer sleeve support ring

5: Shock absorbing elastomer sleeve

6. Clamping Rail (integrated securing

-*screws for Shimano Di2 battery)

7. Seat clamp

8: Cylindrical nut

9: Height adjustment spacer kit

10: Seat clamps for double railed saddles

(10a: upper bracket for round rails / 10b: upper

bracket for oval rails / 10c: lower bracket)

11: Lower saddle mounting brackets

12: Optional kit: brackets for Monolink saddles

10a

10b

10c

1. Position the saddle on the E-Post 2 EVO,

the rails on the outside of the seatpost.

(Fig.1)

2. Insert the upper support (10) indicated in

Fig 5.1 if you want to use a seatpost with

round rails Ø7mm and the support (10b)

indicated in Fig 5.2 for a saddle with oval

rails. (Fig.2)

3. Then insert the lower support (10c)

under the saddle rails. (Fig.3)

4. Put both lower brackets (11) in place and

tighten the previously greased set screw

to the speciﬁed torque of 8Nm once your

seat is properly positioned. (Fig.4)

INSTALLING A DOUBLE OR AN OVAL RAILED SADDLE

Fig 1

Fig 5.1

Fig 5.2

Fig 2

Fig 3

Fig 4

OVERSIZE

Warning:

The E-POST 2 EVO is not compatible

with oval railed saddles with a rail

height greater than 9.6 mm.

1. Grease the screws (7)

2. Position the Monolink® saddle on the

E-Post 2 EVO (Fig.6)

3. Put both upper brackets (12) in place and

loosely tighten the screw. (Fig.7)

4. Then ﬁx the two lower brackets (11) in

place and loosely tighten the screw.

(Fig.8)

5. Adjust your saddle as necessary. First

block the fore and aft movement by hand

tightening the upper screw, then do the

same with the lower screw once the

desired angle is determined. Tighten the

two screws to the torque of 8Nm. (Fig. 9)

INSTALLING A MONOLINK® SADDLE (requires optional adapter kit)

Fig 6

Fig 7

Fig 8

Fig 9

To remove your saddle, or adjust its position, loosen the screw, a few turns, that holds the upper

brackets in place (11).

Gently apply force, alternating between the front and back of the saddle, to loosen the seat

brackets. If they do not come free, due to over tightening, use a small headed mallet and tap

lightly on the screw head, still bound by a few threads, at various angles in order to free the

opposite side.

The tightening of the E-Post 2 EVO is done with a single screw.

REMOVING THE SADDLE

INSTALLATION/REMOVAL OF THE E-POST 2 EVO

1. Insert the seatpost in the frame.

2. Tighten the screws to 4Nm using a torque wrench and a 4mm hex or Allen key.

Fig 10

The E-POST 2 EVO has an integrated

mounting system for the Shimano batteries

SM-BTR2 or BT-DN110.

To mount your battery, secure it to the battery

support (6).

MOUNTING A SHIMANO BATTERY

Notes :

• When a saddle is already installed

on the bicycle, you cannot use a torque

wrench. However, it is still possible to

tighten/loosen the seatpost. To do this,

use a 4mm hex or Allen key by inserting

it into the opening of the screw head.

Tighten moderately so as to not exceed

4Nm.

• To remove your seatpost, loosen the

screw as needed. THE E-POST 2 EVO

should easily come free. If it does not,

loosen the screw some more.

Fig 11

Fig 12

Your new bicycle requires that the seat tube be cut to ﬁt your personal seat height. For this operation,

it is best that you contact your authorized LOOK retailer.

1. Introduce the seatpost into the frame and adjust the horizontal position of the saddle.

2. Before cutting, measure the saddle height of the new bicycle with the saddle in place.

3. Calculate the length “L” to be cut using the following formula: L = seat height on the new bike -

personal seat height

4. Remove the seat post.

5. Place a strip of adhesive tape, centered on the length “L”, in order to protect the post while cutting

6. Install the cutting tool as necessary and

according to the “L” position and tighten to 3

Nm. (Fig.13)

7. Cut the tube using a saw (24 or 32 teeth/inch)

inserted into the tool’s sawing slot. Position the

bicycle in the stand in such a way as to saw in

a vertical position.

8. Remove the cutting tool and deburr the end of

the tube with a piece of ﬁne grain sand paper.

Verify that the end of the tube is clean and free

of paint.

CUTTING THE SEAT TUBE HEIGHT

Fig 13

Fig 14

You can adjust the saddle height by adding

more spacers. THE E-POST 2 EVO comes with

the following spacers: 1mm (qty. 1) / 2mm (qty.

2) / 5mm (qty. 1) / 10mm (qty. 3). The maximum

height allowed for the added spacers is

30mm (i.e. 3x10mm spacers, stacked). To

adjust your seat height:

1. Loosen the 2 EVO E-Post and remove it

from the frame.

2. Place the spacers on the seatpost as

indicated on ﬁg. 14.

3. Install the seat post as per the procedure

previously provided.

ADJUSTMENT OF THE SEAT TUBE HEIGHT

Note : The maximum overlap “L” of the tube is 150 mm in relation to the original length.

Table des matières

Autres manuels Look Accessoires pour vélos

Look

Look GEO CITY GRIP VISION Manuel utilisateur

Look

Look CARBON FORK Manuel utilisateur

Look

Look 796 MONOBLADE RS Manuel utilisateur

Look

Look Keo Blade Track Manuel utilisateur

Look

Look KEO CLASSIC Manuel utilisateur

Look

Look CARBON SEATPOST Manuel utilisateur

Look

Look KEO BLADE Manuel utilisateur

Look

Look RSP Manuel utilisateur

Look

Look 785 HUEZ RS Manuel utilisateur

Look

Look ZED 3 Manuel utilisateur

Look

Look AERO DESIGN HANDLEBAR 2 Manuel utilisateur

Look

Look E POST 2 Manuel utilisateur

Look

Look Aero Design Manuel utilisateur

Look

Look X-TRACK Manuel utilisateur

Look

Look 987 Manuel utilisateur

Look

Look GEO TREKKING Manuel utilisateur

Look

Look KEO BLADE Manuel utilisateur

Look

Look ZED 2 Manuel utilisateur

Look

Look KEO BLADE CARBON Manuel utilisateur

Look

Look E-POST R5 Manuel utilisateur

Look

Look AERGO Manuel utilisateur

Look

Look TRAIL ROC Manuel utilisateur

Look

Look 796 MONOBLADE RS Manuel utilisateur

Look

Look 675 Manuel utilisateur

Manuels Accessoires pour vélos populaires d'autres marques

Sigma

Sigma BC 16.16 Manuel utilisateur

Playcore

Playcore Dero Setbacks Manuel utilisateur

VDO Cyclecomputing

VDO Cyclecomputing x3dw Manuel utilisateur

Cateye

Cateye RAPID X2 Manuel utilisateur

buratti meccanica

buratti meccanica Clorofilla Trail Manuel utilisateur

Shimano

Shimano SG-8R20 Mode d'emploi

BOB

BOB YAK Manuel utilisateur

APLIC

APLIC 303303/20190717TW012 Manuel utilisateur

SRAM

SRAM AXS BlipBox Manuel utilisateur

Garmin

Garmin EDGE 500 Manuel utilisateur

Shimano

Shimano FD-RX810 Manuel utilisateur

Cateye

Cateye V2C - Manuel d'instructions

KMART

KMART 43115907 Manuel utilisateur

SIGMA SPORT

SIGMA SPORT Buster 2000 Manuel utilisateur

NVO Components

NVO Components STEM Manuel utilisateur

DAXYS

DAXYS BP188 Manuel utilisateur

XLC

XLC BV-W17 Manuel utilisateur

Deda Elementi

Deda Elementi SUPERBOX Manuel utilisateur