Look Solutions TINY S Manuel utilisateur

Operating manual

aLook Solutions product

Set of Equipment supplied

– 1 Tiny S

– 2 rechargeable batteries 3.7 V

– 1 remote with cable

– 1 charger

– 1 cable with USB- and Micro-USB-plug

– 1 wall wart 5V

– 6 ﬂuid reservoirs ﬁlled with 5 milliliter ﬂuid each

to be screwed in

_ 1 reﬁll set

to reﬁll the ﬂuid reservoir

– 1 bottle of ﬂuid (250 milliliter)

Please check whether all ordered products are supplied.

Original operating manual, version 01/2013

Contents

1. Procedure of the Tiny S

2. Safety Instructions

3. Descriptions of the parts

4. Fluid

4.1 General

4.2 Refilling the fluid reservoir

5. Operating the Tiny S

5.1 Selecting the Location

5.2 Mounting the Tiny S

5.3 Starting-up the Tiny S

5.4 Status Display of the battery

5.5 Wiring of connectors

6. The rechargeable Battery

6.1 General

6.2 Capacity and life time

6.3 Operating and Storing

6.4 Charging the battery

6.5 Safety Instructions

6.6 Technical Data

7. Service and Maintenance

7.1 Changing the Vaporizer

7.1.1 Removal of the Vaporizer

7.1.2 Installation of the Vaporizer

7.1.3 Calibrating the Vaporizer

7.2 If the machine does not work perfectly 16

7.2.1 There will be no fog if…

7.2.2 Status and error display

7.3 Care and Maintenance 17

8. Technical Data 17

9. Warranty Conditions 18

1. Procedure of the Tiny S

The Tiny S is a battery-powered, microprocessor-controlled mini fog generator. It

is based (as most fog generators are) on the vaporizer principle, i.e. a glycol ﬂuid is

evaporated and condenses into fog when leaving the fog nozzle. However, the Tiny S

only heats when fog is actually produced.

The machine switches off automatically after approx. one minute. Thus, the electronics

of the Tiny S does not use any current.

If the receiver of the radio remote is connected to the machine, some current will

be needed. Please note: Thus, the battery can be destroyed by completely discharging

and cannot be used anymore!

Generally the battery must be disconnected and regularly recharged (at least

every 6 months) if the machine will be not in use or stored for a longer period.

When emitting fog a strong current of 5 to 6 A runs with peak levels of 12 to 13 A.

The following sequence produces fog:

a) Warm up (1 second, without pumping ﬂuid).

b) The pump runs, machine produces fog

c) Post-run mode (15 seconds to vaporize the ﬂuid remaining in the vaporizer).

In the post-run mode the fogging process can be started via the start button in the

lid or via the start button on the cable remote or radio remote.

2. Safety instructions

A fog machine is not a toy!

• Veryhotsteamescapesfromthenozzle.Riskofscalding.

• Occasionallyveryhotdropletsofuidmayescapewheninoperation.

Thus never aim at persons directly and keep a minimum distance of 3 m to the nozz-

le.

• Nevertouchthenozzlewheninoperation.Riskofgettingburnt.

• The location for the machine must be non-ammable, non-combustible and not

sensitive to heat. Its surface area has to be twice as big as the machine.

• Keepaminimumdistanceof60cmtoallammable,combustibleobjectsandobjects

sensitive to heat.

• Glycolisalcoholandburnswithaslightlybluish,almostinvisibleame.Neverpoint

the fog at strong sources of ignition like ﬁre or pyrotechnic effects.

• Neveropenthemachineandleaveitunattendedwhenconnectedtoapowersup-

ply.

• Thevisibilityhastobemorethan2minroomswherepeoplewalkaround.

• OnlyusethesuppliedTINY-FLUID.Differenttypesofuiddonotgeneratethefog

you require and will damage your fog generator.

• Donotswallowthefoguid.Keepitawayfromchildren.Incaseofeyecontact,rinse

well with water. Consult a doctor should you accidentally swallowed some ﬂuid.

• Spilleduidorsplasheduiddropletscancauseasliphazard.Mopuptheuidand

disposeofitaccordingtoregulations.TINY-FLUIDiscompletelywater-solubleand

biodegradable.

• Fogmayactivatesmokedetectors.

Artiﬁcially-made fog can be produced in many different ways. The method used here

to produce fog, with a device which works according to the vaporizer principle, is the

most harmless one.

Nocasehassofarbeenreportedinwhichahealthyhumanbeinghasbeenharmed

because of using our device to produce artiﬁcial fog. However, this can only be gua-

ranteed if the professional fog generators are used appropiately, i.e. at the correct

vaporization temperatures as well as with the correctly mixed fog ﬂuid.

We, however, recommend: People with health problems or problems of the re-

spiratory tract or with an inclination for allergies should avoid any contact with

artiﬁcially-made fog.

· Start button

· Sockets for connecting cable

3. Description of the parts

1: · Ventilation slots

2:·Fognozzle

3: · Screws to unscrew the

stainless steel hood

4: · Start button

5:·YellowLED

11:·Fluidreservoirtobescrewedin

13: · Battery to be screwed in

14: · Charger

3. Description of the parts

· Socket for connecting the

cable of the control panel

7: · Vaporizer

8: ·Fluidtube

9: · Tubing spout

· Slot for ﬂuid reservoir

6: · Screws for connecting the vaporizer

to the connecting pins

· Calibrating button to

calibrate the vapori-

zer

10: · Connecting pins

for vaporizer

12: · Reﬁll set

· Slot for battery

4. Fluid

The location for the Tiny S must

• bedry

• guaranteesufcientairsupply

• beatleast60cmfrominammablematerials

• haveverylittlevibration

• haveanambientoperatingtemperaturebetween5°Cand45°C

• havearelativeairhumidityoflessthan80%.

5.1 Selecting the Location

5.2 Mounting the Tiny S

If the Tiny S is be built into props or similar, make sure that a fog-free air supply is

guaranteed. Too high a fog concentration can condense inside the machine and can

result in damages caused by moisture.

5. Operating the Tiny S

The Tiny SisbuilttobeusedwithoriginalLookTiny-Fluid.Useofotherliquidswill

clog the vaporizer and void the warranty.

4.1 General

The ﬂuid reservoir can be reﬁlled using the delivered reﬁlling set [12]. Thus, the

reservoirs can be used several times.

a) Mount5mlofTiny-Fluidfromtheoriginaluidbottlewiththerellingset.

b) Connect the adaptor of the reﬁlling set with the reservoir you would like to reﬁll.

c) Disconnect the adaptor and screw the reﬁlled reservoir into the Tiny S. If you reﬁll

reservoirs for stock, please use the covers to avoid small bits of dirt inside the reservoir

and make sure the reservoir cannot leak.

4.2 Reﬁlling the ﬂuid reservoir

5. Operating the Tiny S

When installing the Tiny S make sure that

• nofogispassedbackintothefoggenerator,

• nocondenseduidrunsintotheapparatus,

• theairvents[1]arenotcoveredorconcealed,

• noobjectsprotrudeintothefognozzle[2].Thismaydestroythevaporizer.

5.3 Starting up

a) Remove both covers from the already ﬁlled ﬂuid reservoir. Screw the reservoir into

the Tiny S.

The covers should be stored. The reservoirs can be reﬁlled with the delivered reﬁlling

set and can be used several times.

Checkthecleanliness,sothatnodirt(uffetc.)canbesuckedinbythepump.Even

the smallest impurity immediately leads to clogging of the machine.

b) Connect the battery to the machine by putting it into the slot. Make sure the starting

point of the milled ﬂute/groove is up. Press the battery slightly into the slot and

rotateitclockwiseuntilitlocksinplace.TheyellowLED[5]willstarttoash.

To remove the battery, press it slightly into the slot, rotate it anti-clockwise and

withdraw it.

c) Press and hold the start button in the lid of the machine [4]. After approx. 3 seconds

the unit generates fog as long as the button is hold.

If you would like to control the machine via the cable remote, connect the control

cablefortheremotetothemachine.Youcanstartthefoggingprocessbypressing

the start button at the cable remote.

Caution: Do not put anything into the fog nozzle. This may destroy the vaporizer and

it then has to be changed (see point 7.1)

If the Tiny S is not generating fog, the machine switches off automatically after approx.

1minute.TheyellowLED[5]doesnotlightanymore.Themachinecanstillbeactivated

at any time by pressing the start button in the machines lid or the cable remote.

5. Operating the Tiny S

5.4 Battery Status Display

The yellow LED [5] on the Tiny S indicates (among other things (see point 7.2)) how

strong the battery still is and/or when it may need to be recharged.

5.5 Wiring of Connectors

Mini-Stereo jack plug:

Sleeve = Ground, Ring = switch on/off, Tip = 3.7 V DC (+) output, max. 50 mA

1) LEDashesslowly:

Batterycapacityof15%–100%,thebatteryisfullyoperational

2) LEDashesfast:

Batterycapacitybelow15%–thebatteryshouldbechangedand/orcharged.

3) LEDlightsuppermanently:

The battery is ﬂat

Table des matières

Autres manuels Look Solutions Machine à brouillard

Look Solutions

Look Solutions Cryo-Fog Manuel utilisateur

Look Solutions

Look Solutions Tiny F07 Manuel utilisateur

Look Solutions

Look Solutions Tiny CX Manuel utilisateur

Look Solutions

Look Solutions UNIQUE 2 Manuel utilisateur

Look Solutions

Look Solutions Cryo-Fog Manuel utilisateur

Look Solutions

Look Solutions Tiny FX Manuel utilisateur

Look Solutions

Look Solutions Power-Tiny Manuel utilisateur

Look Solutions

Look Solutions Viper NT Manuel utilisateur

Look Solutions

Look Solutions Unique 2.1 Manuel utilisateur

Look Solutions

Look Solutions Viper NT Manuel utilisateur

Look Solutions

Look Solutions Orka deLuxe Manuel utilisateur

Look Solutions

Look Solutions Cobra 3.1 Manuel utilisateur

Look Solutions

Look Solutions Unique 2.1 Manuel utilisateur

Look Solutions

Look Solutions Viper 2.6 Manuel utilisateur

Manuels Machine à brouillard populaires d'autres marques

Antari

Antari ICE Manuel utilisateur

Boost

Boost BOOST-FOG400LED-BK Manuel utilisateur

Home Accents Holiday

Home Accents Holiday FM1000-ASH Manuel utilisateur

EuroLite

EuroLite ZEITGEIST FOG-1200 Manuel utilisateur

Dyna-Fog

Dyna-Fog CYCLONE ULTRA 2734 Manuel utilisateur

PROEL

PROEL DRAGO HEAVY PLFD150HY Manuel utilisateur

Sparklyn

Sparklyn Y846 Manuel utilisateur

Magicfx

Magicfx CO2 Gun Manuel utilisateur

Ibiza

Ibiza LSM500LAS Manuel utilisateur

Antari

Antari M-5 Manuel utilisateur

Venue Lighting Effects

Venue Lighting Effects ULTRA MINI-FOGGER Manuel utilisateur

High End

High End F-100 Manuel utilisateur

Chauvet

Chauvet ARENA 2100 FLEX Manuel utilisateur

Antari

Antari X FAZER Manuel utilisateur

Beamz

Beamz F1600 Manuel utilisateur

Sagitter

Sagitter SG ARS900C Manuel utilisateur

KISANKRAFT

KISANKRAFT KK-STF-480 Manuel utilisateur

Orion

Orion OT-U250PP Mode d’emploi