LOCKLY GUARD DEFENDER 238LM Manuel utilisateur
WWW.LOCKLYPRO.COM
FOR COMMERCIAL USE & PROFESSIONAL INSTALLATION
USER MANUAL
DEFENDER
(238LM/238LE)
TABLE OF CONTENTS
Table of Contents
Section 5 - Advanced Features
Section 6 - Important Notes
Section 7 - Cleaning
Section 8 - Safety Precautions
5.1 Offline Access CodeTM (OAC)
Section 1 - Product Highlights
Section 2 - Product Overview
2.1 Product Overview- Exterior
2.2 Understanding Your New Lock
2.3 Locking/Unlocking with App
2.4 Rebooting Lockly Guard
2.5 Low Battery
2.6 Changing the Battery
1.1 Product Features
Section 3 - Using Your Smart Lock
3.1 Configuring Access
3.2 Entering Programming Mode
3.3 Pairing to a New Mobile Device
3.4 Adding an Access Code
3.5 Checking/Deleting an Access Code
3.6 Adding a Fingerprint
3.7 Adding/Deleting Fingerprints
3.8 Fingerprint Scanning Directions
3.9 Fingerprint Scanning Tips & Troubleshoot
3.10 Adding an RFID card
3.11 Checking/Deleting an RFID Card
Section 4 - Locking and Unlocking
2
3
3
4
5
6
1
7
8
8
10
10
11
12
13
14
14
15
16
17
18
19
19
20
22
23
24
24
4.1 Unlocking with Access Codes
4.2 Unlocking/Locking with Fingerprints
4.3 Unlocking with RFID
4.4 Locking/Unlocking with Physical Key
4.5 Unlock with QR Code
4.6 Safe Mode
4.7 Locking from the Outdoor
4.8 Rain Mode
4.9 Shine Mode
4.10 Welcome Mode
For additional support, visit http://LocklyPro.com/support
25
26
27
27
SECTION 1.1 1
Patented Hack-proof PIN Genie Keypad
Digits are randomly displayed on the keypad ensuring access codes to be unde-
tectable to intruders after repeated use. Numbers are randomly distributed across 4
buttons, with 3 numbers in each button. Users can press any button showing their
number. Location of the numbers are always different everytime someone uses the
keypad, making it hard for prying eyes to guess the correct code.
Multiple Access Codes & Monitoring
Store up to 1033 Access Codes and monitor each entry and exit records.
Advanced 3D Fingerprint Recognition
Biometric Fingerprint Recognition protocol allows up to 99 registered fingerprints to
be used and accepts only actual fingerprints - preventing lifted prints from being
used.
RFID Card Access
Store up to 999 MIFARE RFID cards
Live Monitoring
Through your smartphone, monitor door access from anywhere in the world and
securely control who comes and goes.
Offline Access CodeTM (OAC)
The offline access codeTM can allow owners to issue access codes, set the allowed
access duration, all without Lockly Guard ever connecting to the internet, so in
case of power outage, you can still magically and remotely issue Access Codes
without any connection to the web.
Automatic Lock
Owners no longer have to worry about forgetting to lock the door. With Auto Lock
enabled, Lockly Guard will automatically re-lock the door based on your custom-
ized timing set between 5-300 seconds. (Note: Auto locking only supports latches)
Backup Keys and 9V Battery Socket
The door can be opened with physical backup keys. There is also a 9V battery con-
nection socket for emergency power backup to access the keypad in case your
smart lock runs out of battery.
1.1 Product Features
2 SECTION 2.1
2.1 Product Overview- Exterior
Program Button
Reboot Button
9V alkaline battery
Battery Compartment
*Operated by 4 X AA
size alkaline batteries
Welcome/ Safe Mode
Battery Indicator
OK Button
Exterior Handle
Battery Cover
Touchscreen
Keypad
RFID Card Reader
Key Hole
Fingerprint Reader
SECTION 2.2 ~ 2.3 3
After the installation of your new Lockly Guard, understanding some key functions of
operating your smart lock is important. The following guides will walk you through
resetting a lock, adding/deleting Access Codes, adding/deleting fingerprints,
adding/deleting RFID cards and also how to configure your OAC (Offline Access
Code™)
For any questions you can always visit http://LocklyPro.com/support for assistance.
2.2 Understanding Your New Lock
The Default Access Code is 1 2 3 4 5 6
NOTICE
2.3 Locking/Unlocking with App
Lockly Guard works best with our iOS and Android app.
You must have the LocklyPro
iOS or Android app installed in order to lock and unlock with smartphone. Download
the app by visiting the link below or search "LocklyPro" from the correct app store.
Scan or visit
LocklyPro.com/app
PRO
4 SECTION 2.4
2.4 Rebooting Lockly Guard
Press and release the reboot button when you want to reboot the lock. Your Lockly
Guard will beep once after reboot. Only reboot when necessary.
To reboot, find the reboot button from the bottom of Lockly Guard.
You will need something small such as a paperclip, to press the reboot button. Insert
the paper clip and press down firmly.
NOTICE Reboot Lockly Guard in case of dead battery or malfunc-
tion. No settings will be changed and all Access Codes will
still be stored within Lockly Guard.
Reboot
Button
SECTION 2.5 5
When the battery is in seriously low condition, Lockly Guard will make continuous
beeping sounds in addition to the flashing low battery icon on the touch screen. You
should replace batteries immediately to avoid your smart lock from shutting down.
When your smart lock low-battery warning alert finally dies, you will have 3 chances
to unlock your smart lock either by a password, APP or fingerprint. If the unlock was
successful, the low-battery warning alert will be on for 1 minute. After which, the
smart lock will go to dead-battery mode and will lock auto lock in 5 seconds and the
screen will display a low-battery icon.
Your Lockly will automatically detect battery
polarity. So hold your 9V battery lead in place
against bottom of the Lockly to temporarily
activate the screen to enter your Access
Code. Be sure to hold the 9V battery against
the contact points located at the bottom of
the lock until you have successfully unlocked
your door with your Access Code.
Once unlocked, batteries should be replaced
immediately.
2.5 Low Battery
Dead
Battery
Condition Indicator Solution
Low
Battery
Replace batteries immediately
to avoid battery failure.
Lockly
Guard
can still operate up to 300
cycles in low battery condition.
When there is no
display and sounds;
and screen is non-
functional.
Replace batteries immediately.
Supplied physical backup keys
can be used to unlock the door.
Alternatively, Use a 9V battery
as shown below to temporarily
activate the lock.
Battery Icon on the
display keypad will
light up to indicate
low battery
Touchscreen
9V
alkaline
battery
6 SECTION 2.6
2.6 Changing the Battery
Open the battery compartment cover and insert 4 AA alkaline battery as shown
below.
• Make sure the batteries are correctly oriented.
• Replacement of batteries does not affect programmed data.
• Replace only with new batteries. DO NOT mix with used batteries.
Whenever batteries are replaced, reconnecting
the
smart lock to your smartphone App is required.
If you have not yet downloaded the app, visit:
LocklyPro.com/app
NOTICE
Use a screwdriver to push the back screw stopper up then loosen the screw.
Remove the battery cover.
Unplug the terminals of the battery compartment then install the batteries.
1
2
3
3
1 2
SECTION 3.1 7
3.1 Configuring Access
How to Use the Keypad
There are a total of five (5) buttons on the keypad as
shown in the example image to the left. The numbers
in each button may differ than what is shown on your
device than what is displayed here.
To enter your required digit, just simply press the circle
where your number is shown. You do not need to
press the actual number as anywhere within the circle
will suffice.
The button on the bottom is the OK button. You will be
pressing this button when you are done entering your
Access Code.
Your new Lockly Guard Access Code can be any combination of 6 to 8 digits.
Once a new Access Code is entered, the Default Access Code of 123456 would be
deleted.
Lockly Guard Defender can support up to 1033 sets of Access Codes. It comes with
60 access codes for free. To add more access codes, subscription to Lockly\OS is
www.locklyOS.com to learn more.
OK Button
The Default Access Code is 1 2 3 4 5 6
NOTICE
8 SECTION 3.2 ~3.3
3.2 Entering Programming Mode
*The activation code card is attached to the welcome card inside the package.-
Store it for future use. Once you have registered your lock on the LocklyPro app, you
have the option to save it on the PIN Genie Vault. To access details for future use,
check your account information and go to PIN Genie Vault.
To end Programming Mode, press the Program button anytime. Programming Mode will
automatically exit if the keypad is inactive for more than thirty (30) seconds.
Bluetooth Activation
ModeNumber
Program Button
3.3 Pairing to a New Mobile Device
Pair with Bluetooth
While in Programming Mode, select “BL” to pair a new smart phone. If
you are not in Programming Mode, please see Section 3.2 to enter
Programming Mode.
After pressing “BL”, the BL icon will flash and you will here short beeps.
You need to wait and allow the pairing of new devices.
You will hear long beep and the green light will be on if the pairing is
successful. You will here 3 short beeps and the red light will be on if
pairing is unsuccessful. You will need to reenter the programming
mode, then Bluetooth pairing mode"BL" to re-pair the device.
To enter Programming Mode, remove the battery
compartment cover on the interior side of the
Lockly Guard to expose the Program button.
Short press the program button to enter program-
ming mode. Enter administrator fingerprint, RFID
card, activation code* or administrator access
code (the initial administrator password is 123456)
then tap
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels LOCKLY GUARD Serrure de porte
LOCKLY GUARD
LOCKLY GUARD DEADBOLT 728Z Manuel utilisateur
LOCKLY GUARD
LOCKLY GUARD DEADBOLT 728F Z Manuel utilisateur
LOCKLY GUARD
LOCKLY GUARD DEADBOLT 728F Z Manuel utilisateur
LOCKLY GUARD
LOCKLY GUARD DEFENDER SLIDE EDITION Manuel utilisateur
LOCKLY GUARD
LOCKLY GUARD 698L Manuel utilisateur
LOCKLY GUARD
LOCKLY GUARD DUO INTERCONNECTED EDITION Manuel utilisateur
LOCKLY GUARD
LOCKLY GUARD DEADBOLT 728F ZU Manuel utilisateur
LOCKLY GUARD
LOCKLY GUARD ATHENA 228SL Manuel utilisateur
LOCKLY GUARD
LOCKLY GUARD VISION DUO Manuel utilisateur
LOCKLY GUARD
LOCKLY GUARD VISION DUO Manuel utilisateur
