Livith EASY SPIN Manuel utilisateur
MANUAL EASY SPIN
FLEX / MULTIFLEX
MULTISPIN
RIGID / RIGID FLAT
SMARTRING
VERTICAL / VERTICAL F
GRUVY / GRUVY FLAT
WWW.LIVITH.IT
2
WARRANTY TERMS
AND CONDITIONS
3
WWW.LIVITH.IT
INDEX
07
12
15
17
27
10
16
14
25
INSTALLATION
GUIDE
ACCESS PLATES
SYSTEM
PERFORMANCE
ASSISTANCE
FALL INDICATOR
MAINTENANCE
GUIDE
PPE USE GUIDE
DEVICE
CERTIFICATES
WARRANTY TERMS
AND CONDITIONS
4
5
WWW.LIVITH.IT
INTRODUCTION
Dear Customer,
Thank you for choosing a Livith product.
This Manual was created to assist you during the design, installation, use and maintenance
phases and to provide you with the necessary information on the product you have
purchased.
The design, installation, use and maintenance of Livith products must be carried out only
aer viewing the following manual and according to the assembly instructions. Livith
declines all responsibility for malfunctions related to the incorrect performance of the
product these operations or to the use of the components of the devices in an improper
way and not in compliance with the indications of this manual and of the product
assembly instructions.
If the technical information provided by us should not be reected during
one of the operations, please contact us immediately by visiting the
website www.livith.it
It is forbidden to reproduce this Manual, even partially, by any means or technique,
without authorization from Livith SpA.
The anchoring devices produced by Livith SpA to which this manual refers comply with
the following TECHNICAL STANDARDS:
UNI 11578: 2015
REGULATORY REFERENCES
EN 795: 2012 CEN / TS 16415: 2013
6
WARNINGS
All the devices produced and marked by Livith SpA have undergone all the performance
and durability tests required by the technical standards to which this manual refers.
Livith SpA operates as a quality company, therefore it guarantees the quality of its
products and manufacturing processes by aixing the appropriate marking and ISO
9001: 2018 certication.
Any other use is prohibited, in particular as elements used for liing equipment
or other loads.
The user who uses it as an anchor point as a part of a fall arrest system must be
equipped with PPE and connection devices equipped with an energy absorber
or other components, compliant with UNI EN 355: 2003, aimed at limiting the
dynamic force of fall arrest within 6kN.
Use by qualied personnel is recommended.
All Livith devices and systems have been designed as anchoring devices that are part of
fall arrest systems and therefore exclusively aimed at protecting against falls from height.
Livith declines all responsibility for damage to person or things related to the use of
the devices with unsuitable PPE.
Livith declines all responsibility for damage to persons or things related to the use
of the devices in a way that does not comply with the current safety regulations.
CERTIFICATE NUMBER: 68754 / A / 0001 / UK / IT
7
WWW.LIVITH.IT
INSTALLATION GUIDE
Read and keep this Manual and make it available for future users and maintainers
of the anchoring device.
This device must be installed by competent and qualied operators or companies.
The marking must be accessible.
Follow the instructions for correct xing provided by Livith SpA or dened by the
FIXITH ETC TM soware.
For any additional xing elements go to the website www.livith.it
These indications are not a substitute for the specic calculation report and can be taken
as a reference only for the installation of Livith products.
Livith declines all responsibility for malfunctions related to incorrect xing or poor
capacity to absorb loads by load-bearing structures intended to house the anchoring
devices.
For any assistance in this regard, go to the website www.livith.it
This manual contains instructions intended to inform about the correct assembly, use
and maintenance of LIVITH anchoring devices, as well as the correct design of fall arrest
systems.
Therefore it is essential to preserve the manual for the entire life of the device, since it is
an integral part of it.
The person responsible for managing the anchoring device must ensure that this user
manual, together with the technical le of the work, are kept in good condition and must
make them available for the user, the maintenance technician or the inspector, before any
access at height and use of the system.
In case of loss, this manual can be requested in paper form from LIVITH SpA.
ADVICES AND REQUIREMENTS
8
The installation of the device must take place avoiding that, in case of fall arrest,
the deection of the line leads it to come into contact with sharp edges or with
other elements that could contribute to damage it.
Once installed, anchoring devices can be subject to the capture of atmospheric
discharges. It will therefore be responsibility of the owner or manager of the fall
arrest system to check, based on the regulations in force on the matter, whether
or not the building is subject to lightning risk and if necessary take charge and
burden of protecting the building with suitable measures and systems suitably
designed according to current standards.
The installation of the anchoring devices must be carried out away from high
voltage cables, electrical systems and must not have connections with them or
with antennas or other systems that can become live and act as conductors, as
the devices produced by Livith S.p.A can accidentally go live. An accurate risk
assessment is required in this regard.
In case of installation on inclined slopes. It is also necessary to install a snow stop
system near the anchoring device to reduce the snow load acting on it.
Livith S.p.A declines all responsibility related to the system being put out of
service due to the failure to install snow stopper systems.
For further information please consult the Warranty Conditions at the end of this
Manual.
Installation specication
9
WWW.LIVITH.IT
MAX. FORCE EXERTED ON THE ANCHORS * [KN]
Max number of
operators
1 Operator 2 Operators
EASYSPIN 9.0 -
FLEX 9.0 12.0
MULTIFLEX 9.0 12.0
MULTISPIN 9.0 12.0
RIGID 9.0 -
RIGID FLAT 9.0 -
SMARTRING 9.0 -
VERTICAL H40 6.6 11.0
VERTICAL 7.8 10.4
VERTICAL F H30 7.0 -
VERTICAL F H40 6.3 -
GRUVY 9.0 -
GRUVY FLAT 9.0 -
* See chapter regarding system performance on page. 10
Type A devices oer all the performance characteristics required for Type A fall arrest
anchors, governed by the standards to users..
To know the geometric characteristics of the dierent devices, download the
technical data sheets on www.livith.it
TECHNICAL FEATURES
10
Livith deformable Type A devices are designed to cushion the dynamic impulsive force
stressing the anchor in the event of a fall, by plastically deforming.
Hereaer are the deformations and stresses acting on the Type A anchors deformable in
the event of a fall.
For all non-deformable Livith devices, check with the forces indicated on page. 9 of this
Manual, considering the device in its undeformed conguration and the stress factor
acting in the most severe operating direction.
SYSTEM PERFORMANCE
DATA 1 OP. 2 op.
Maximum stress force [kN] 6.56 11.0
Deformed height [mm] 230 135
DATA 1 OP. 2 op.
Maximum stress force [kN] 7.83 10.4
Deformed height [mm] 170 135
Ce manuel convient aux modèles suivants
10
Table des matières
Manuels Équipements de sécurité populaires d'autres marques
Innova
Innova Xtirpa Mode d’emploi
bolle SAFETY
bolle SAFETY B810 Manuel utilisateur
SHENZHEN FANHAI SANJIANG ELECTRONICS
SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Manuel utilisateur
Hiltron security
Hiltron security POWER8E Mode d’emploi
Hatco
Hatco B-950P Manuel utilisateur
Sitec
Sitec TX MATIC Manuel utilisateur
