Lippert Components Solera Manuel utilisateur

lci1.com 574-537-8900 Rev: 03.21.19

Solera®

Universal Hardware

Manual Awning to

Solera 18V Power Awning

(For Aftermarket Applications)

CCD-0001267

Table of Contents

Introduction ............................................ 2

Additional Information Sources ........................ 2

Safety Information ..................................... 2

Parts List ................................................ 3

Resources Required ................................... 4

Preparation ............................................. 4

Optional Upper Mounting Brackets .................... 4

Conversion ............................................. 5

Dometic Manual Awning to Solera 18V Power Awning 5

Carefree Manual Awning to Solera 18V Power Awning ... 9

Charging the Battery ................................. 13

Operating the Awning ................................ 13

Extending and Retracting The Awning ............... 13

Adjusting the Pitch ................................... 14

Troubleshooting ...................................... 15

Manual Override ..................................... 15

Troubleshooting Chart ............................... 16

Maintenance .......................................... 17

Fabric Care .......................................... 17

Notes .................................................. 18

Solera®

Universal

Hardware

Manual Awning

to Solera 18V

Power Awning

(For Aftermarket Applications)

Solera 18V Power Awning Kits

Part # Description

434729 Solera Power 18V 69” Kit, Black

434730 Solera Power 18V 69” Kit, White

Tall Arm (69”)

Solera 18V Tall Arm (69”) requires:

• 69” of unobstructed area from the awning rail straight

down.

• Minimum clearance of 2 ½” between the awning rail and

the top of the entry door.

lci1.com 574-537-8900 Rev: 03.21.19

Solera®

Universal Hardware

Manual Awning to

Solera 18V Power Awning

(For Aftermarket Applications)

CCD-0001267

Introduction

The Solera®18V Power Awning features a unique,

rechargeable battery that ts right inside the awning arm

and comes with everything you need to connect to the

awning motor wire.

NOTE: The LCI Solera Universal Hardware kit for a manual

to power conversion will ONLY t Dometic and Carefree

awnings.

Additional Information Sources

Additional information about this product can be obtained

from www.lci1.com/support or by using the myLCI app.

Replacement components can be ordered from

https://store.lci1.com/ or by using the myLCI app. The

myLCI app is available for free on iTunes®for iPhone®and

iPad®and also on Google Play™for Android™users.

iTunes, iPhone, and iPad are registered trademarks of

Apple Inc.

Google Play and Android are trademarks of Google Inc. MOVING PARTS CAN PINCH, CRUSH OR CUT. KEEP

CLEAR AND USE CAUTION.

FAILURE TO USE THE INSTALLED SAFETY FEATURES

MAY RESULT IN DEATH, SERIOUS INJURY, DAMAGE TO

THE UNIT AND/OR VOIDING A WARRANTY.

Safety Information

Warning, Caution and Danger symbols indicate that an

installation procedure has a safety risk involved and may

cause death, serious injury or property damage if not

performed safely and within the parameters set forth

in this manual.

Manual awnings that contain springs use tension for ease

of operation and can be harmful to the end user should the

stored tension come unbound. Cotter pins, travel locks and

cam locks are installed and MUST be used to contain the

tension when the system is being serviced.

lci1.com 574-537-8900 Rev: 03.21.19

Solera®

Universal Hardware

Manual Awning to

Solera 18V Power Awning

(For Aftermarket Applications)

CCD-0001267

Parts List

Callout PN Solera Power 18V 69” Kit

Common Parts Qty

J 237315 Rivet, 3/16” x 1.3” 8

K281079 Screw, #6-20 x 1/2” Self-Drilling

Hex Washer 2

L 298760 Hairpin Cotter Pin, 0.093” x 2-5/16” 4

M 347119 Cotter Pin, 1/8” x 3” 2

N384905 Screw, #10 - 32 x 2 1/2” Stainless Steel

Pan Head 2

O 384906 Nylon Locking Nut, #10 - 32 2

P 438247 Cable Tie, Standard, NYL - 30 2

Callout PN Solera Power 18V 69” Kit

434729 Black Qty

A 276611 Screw, #8-18 x 1/2” Pan Head 6

B281154 Support Arm Assembly 1

C 656484 Support Arm Assembly - Battery Pack 1

D 360575 Screw, #8 - 32 x 1/2” Pan Head 2

E 384965 Bracket, Upper Solera Power 2.500” 2

F423751 End Cap 2

G 346891 Rivet, 3/16” x .450” 1

H 672050 Drive Head Assembly Regal Awning 1

I 672052 Idler Head Assembly Regal Awning 1

A BC

F G H

I J K

L M N

O P

Callout PN Solera Power 18V 69” Kit

434730 White Qty

A 675906 Screw, #8 - 18 x 1/2” Pan Head 6

B281152 Support Arm Assembly 1

C 656483 Support Arm Assembly - Battery Pack 1

D 299630 Screw, #8 - 32 x 1/2”Pan Head 2

E 384964 Bracket, Upper Solera Power 2.500” 2

F423750 End Cap 2

G 346890 Rivet, 3/16” x .450” 1

H 672049 Drive Head Assembly Regal Awning 1

I 672051 Idler Head Assembly Regal Awning 1

NOTE: Part numbers are shown for identification purposes

only. Not all parts are available for individual sale. All parts

with a link to the Lippert Store can be purchased.

lci1.com 574-537-8900 Rev: 03.21.19

Solera®

Universal Hardware

Manual Awning to

Solera 18V Power Awning

(For Aftermarket Applications)

CCD-0001267

Fig.1

Resources Required

• 1-2 people, depending on task

• Cordless or electric drill or screw gun

• Appropriate drive and drill bits

• Socket wrench

• ⁄” Socket

• Rivet gun

• Locking pliers

• Ladder

• Silicone sealant

• Non-permanent method of marking

Optional Upper Mounting

Bracket Installation

This procedure is O NLY needed if replacing support arm

assemblies that had upper mounting brackets. This will

avoid making additional holes in the unit. If upper brackets

are NOT needed, proceed to the Conversion section.

If replacing support arm assemblies that had upper

mounting brackets (Fig.1A) that straddled the awning rail

(Fig.1B), exchange the angle bracket already attached

to the new support arm assembly with the new provided

upper mounting bracket, bolt and nylon locking nut.

1. On the new power awning support arm assembly, drill

out the four rivets holding the original upper mounting

bracket supports to the support arm assembly (Fig.2A).

Set the two upper mounting brackets aside.

2. Align the new upper mounting bracket bolt guide

(Fig.3A) at the top set of holes of the support arm

assembly (Fig.3B).

Fig.2

Fig.3

lci1.com 574-537-8900 Rev: 03.21.19

Solera®

Universal Hardware

Manual Awning to

Solera 18V Power Awning

(For Aftermarket Applications)

CCD-0001267

Conversion

Dometic Manual Awning to Solera 18V Power

Awning

NOTE: All screws supporting the awning assembly must

have a backer within the structure of the wall of the unit.

NOTE: This manual will refer to the “drive side” and “idler

side” throughout for various instructions. The “drive side” is

the right hand side of the awning when facing the awning

from the exterior of the unit. The “idler side” is the left

hand side of the awning when facing the awning from the

exterior of the unit.

When converting a Dometic Manual Awning to a Solera

18V Power Awning, the converted awning will be

approximately 2” wider than the initial awning. Be sure

there are no obstructions that may interfere with the

installation of the support arm assemblies PRIOR to

beginning the conversion process.

1. Unlock the travel locks, move the cam lock to the roll out

position and extend the awning approximately 12”.

2. Insert a cotter pin (Fig.5C) into the end cap (Fig.5A)

at each end of the awning.

3. On the drive side of the awning, and with an assistant

holding the roll tube, use a ⁄” socket to remove the

bolt securing the drive head (Fig.5B) to the support arm

(Fig.5D).

A B

C D

Fig.4

Fig.5

3. Insert the provided #10 - 32 x 2 ½” screw (Fig.4A)

through the support arm assembly, through the upper

mounting bracket bolt guide and into the other side of the

support arm assembly.

4. Attach the provided #10 - 32 Nylon Locking nut to the

bolt to hold the bracket in place (Fig.4B).

5. Repeat steps 1-4 for the other support arm assembly.

6. Set the support arm assemblies aside and proceed with

the Conversion section.

NOTE: Once the support arm assemblies with the new

upper mounting brackets are ready to be installed, use

the same holes located in the unit wall that were left when

removing the old arm assemblies.

A B

lci1.com 574-537-8900 Rev: 03.21.19

Solera®

Universal Hardware

Manual Awning to

Solera 18V Power Awning

(For Aftermarket Applications)

CCD-0001267

4. Separate the drive head from the support arm and

secure the support arm to the unit in the travel position.

5. Remove the fasteners from the upper mounting bracket

(Fig.6A) of the support arm assembly.

6. Detach the support arm assembly from the lower

mounting bracket. Discard the mounting bracket.

7. Remove the fasteners from the lower mounting bracket

(Fig.7A) of the support arm assembly.

THE SPRING IS UNDER EXTREME TENSION. IMPROPER

HANDLING COULD CAUSE DEATH, SERIOUS INJURY

OR PROPERTY DAMAGE.

8. Firmly take hold of the drive head with a pair of locking

pliers (Fig.8). Remove the cotter pin from the end cap and

move the cam lock to the roll up position.

NOTE: Padding the locking pliers will prevent the

scratching of components.

9. Slowly release all of the tension by rotating the drive

head with the locking pliers.

10. Using an appropriately-sized drill bit, drill out the rivets

securing the end cap to the roll tube.

11. Remove the end cap and spring assembly (Fig.9B)

from the roll tube (Fig.9A).

Fig.8

Fig.9

Fig.6 Fig.7

lci1.com 574-537-8900 Rev: 03.21.19

Solera®

Universal Hardware

Manual Awning to

Solera 18V Power Awning

(For Aftermarket Applications)

CCD-0001267

A B

12. Place the Solera end cap (Fig.10B) on the end of the

roll tube (Fig.10A), making sure it is properly seated and

the roll tube channel is aligned with the channel on the

end cap.

13. Secure the Solera end cap to the roll tube with the

provided rivets.

NOTE: It may be necessary to drill out the previous holes

in order to accommodate the larger-sized rivets.

14. Pull the cotter pin from the idler side end cap, making

sure to keep a rm hold on the roll tube to avoid injury or

damage to the unit. (Pulling the cotter pin allows the roll

tube to turn for installation of the drive head).

A CB

15. Insert the Solera drive head assembly shaft (Fig.11B)

into the end cap (Fig.11A).

NOTE: When identifying the drive head assembly from the

idler head assembly, the drive head assembly will have an

override plug (Fig.11C). The idler head assembly will not.

Fig.10

16. Align the holes in the shaft and end cap and secure

with the provided #8 - 32 x ½” wax screw (Fig.12A).

FAILURE MAINTAIN CONTROL OF THE ROLL TUBE

AND HEAD MAY RESULT IN DEATH, SERIOUS

INJURY, DAMAGE TO THE UNIT AND/OR VOIDING A

WARRANTY.

NOTE: Keep the head of the wax screw ⁄” from fastened

to avoid compromising the structural integrity of the wax screw.

17. Place the drive support arm assembly directly under

the awning rail so the top of the mount arm is touching the

bottom of the rail.

18. Slide the drive support arm assembly outward to align

below the holes of the awning previously removed before

securing the upper bracket.

Fig.11

Fig.12

lci1.com 574-537-8900 Rev: 03.21.19

Solera®

Universal Hardware

Manual Awning to

Solera 18V Power Awning

(For Aftermarket Applications)

CCD-0001267

Fig.14

Fig.13

NOTE: Silicone sealant MUST be used on all screws and

holes to prevent water from inltrating the unit.

NOTE: Do NOT install fasteners to the lower and middle

sections of the wall mount arm at this time.

20. Re-install the cotter pin to the idler side end cap.

To properly align the hole for the cotter pin, it may be

necessary to slightly move the awning in or out using

the extend/retract switch. See Operation section in this

manual.

21. Repeat Steps 3-19 for the idler side of the awning,

skipping all cam lock instructions.

NOTE: Because the converted awning is approximately

2” wider than the previous awning, the support arm

assembly on the idler side will NOT align with the previous

holes. It is the customer’s responsibility to ll in/seal any

and all holes left on the unit after installation.

NOTE: The idler head does NOT have a cam lock. The

cotter pin is holding all the tension of the spring assembly.

NOTE: Be sure to handle the assembly with care and

always have a secure hold of the idler head.

22. Once the drive and idler side conversions are

complete, cut the nylon ties containing the support arm

assemblies.

23. Use the operation switch at the bottom of the drive

arm assembly to fully extend the awning. See Operation

section of this manual.

24. Remove the manual pull strap from the roll tube.

NOTE: If the drive arm’s battery is not charged, plug the

battery wires into the charger and the charger into a 110V

outlet. See Charging the Battery section in this manual.

The awning should become operational within ve minutes

after being plugged in.

25. Remove the wire covers on the drive support arm

assembly to expose the lower and middle sections of the

mount arm.

19. To secure the drive support arm assembly:

A. If using the original angle bracket on the new

support arm assembly, secure the upper section of the

drive mount arm to the unit with two of the provided

#14 - 10 x 1 ¼” screws (Fig.13).

B. If using the upper mounting bracket, attach the upper

mounting bracket (Fig.14A) of the assembled support arm

assembly, using the previously removed screws.

Go through the top holes of the upper mounting bracket

and into the pre-existing holes in the wall of the unit. All

screws supporting the awning assembly MUST have a

backer within the structure of the wall of the unit.

lci1.com 574-537-8900 Rev: 03.21.19

Solera®

Universal Hardware

Manual Awning to

Solera 18V Power Awning

(For Aftermarket Applications)

CCD-0001267

26. Secure the lower (Fig.15) and middle (Fig.16) sections

of the drive mount arm to the unit with the provided

#14 x 1 ¼” screws or rivets. Make sure the arm is square

on the unit wall. There will be two screws in the lower holes

and two screws in the middle holes.

NOTE: For units with berglass sidewalls, LCI requires the

use of rivets for securing the lower and middle sections of

the mount arm.

NOTE: All screws supporting the awning assembly MUST

have a backer within the structure of the wall of the unit.

NOTE: Silicone sealant MUST be used on all screws and

holes to prevent water from inltrating the unit.

27. Repeat Steps 25-26 for the idler mount arm.

28. Replace the wire covers.

Fig.15

Fig.17

Carefree Manual Awning to Solera

18V Power Awning

NOTE: All screws supporting the awning assembly MUST

have a backer within the structure of the wall of the unit.

NOTE: This manual will refer to the “drive side” and “idler

side” throughout for various instructions. The “drive side”

is the right hand side of the awning when facing the awning

from the exterior of the unit. The “idler side” is the left

hand side of the awning when facing the awning from the

exterior of the unit.

1. Unlock the travel locks, move the cam lock to the roll out

position and extend the awning approximately 12”.

2. Insert a cotter pin (Fig.17A) into the end cap (Fig.17B) at

each end of the awning.

NOTE: Some Carefree systems do not have a hole on the

drive end cap for the cotter pin. In this instance, the cam

lock MUST remain in the roll out position until it is time to

release the tension in the springs.

Fig.16

lci1.com 574-537-8900 Rev: 03.21.19

Solera®

Universal Hardware

Manual Awning to

Solera 18V Power Awning

(For Aftermarket Applications)

CCD-0001267

NOTE: Some Carefree systems are equipped with a cam

lock assist on the drive side of the awning. If equipped,

remove the cam lock assist (Fig.18B) from the lock pin

(Fig.18A), making sure the cam lock remains in the

roll out position.

A B

Fig.18

3. With an assistant holding the roll tube (Fig.19A), remove

the fastener securing the drive head (Fig.19B) to the

support arm.

A B

Fig.19

4. Separate the drive head from the support arm and

secure the support arm to the unit in the travel position.

5. Remove the fasteners from the upper mounting bracket

(Fig.20) of the support arm assembly.

6. Detach the support arm assembly from the lower

mounting bracket.

7. Remove the fasteners from the lower mounting bracket

(Fig.21) of the support arm assembly. Discard the

mounting bracket.

8. Firmly take hold of the drive head with a pair of locking

pliers (Fig.22). Remove the cotter pin, if equipped, from the

end cap and move the cam lock to the roll up position.

NOTE: Padding the locking pliers will prevent the

scratching of components.

THE SPRING IS UNDER EXTREME TENSION. IMPROPER

HANDLING COULD CAUSE DEATH, SERIOUS INJURY

OR PROPERTY DAMAGE.

Fig.21Fig.20

Autres manuels pour Solera

Table des matières

Autres manuels Lippert Components Accessoires automobiles

Lippert Components

Lippert Components ground control 3.0 Manuel utilisateur

Lippert Components

Lippert Components Innolight Sliding Instructions d'installation

Lippert Components

Lippert Components ABOVE FLOOR SLIDEOUT SYSTEM Manuel utilisateur

Lippert Components

Lippert Components Kwikee Manuel utilisateur

Lippert Components

Lippert Components Solera Instructions d'installation

Lippert Components

Lippert Components Curt Rota-Flex Pin Box Manuel utilisateur

Lippert Components

Lippert Components SolidStep XF Manuel utilisateur

Lippert Components

Lippert Components Happijac Manuel utilisateur

Lippert Components

Lippert Components OneControl Hotspot Manuel utilisateur

Lippert Components

Lippert Components Alumi-Tread series Manuel utilisateur

Lippert Components

Lippert Components Happijack FT-DR2 Manuel utilisateur

Lippert Components

Lippert Components In-Wall Slide-Out Manuel utilisateur

Lippert Components

Lippert Components Tire Linc Manuel utilisateur

Lippert Components

Lippert Components Solera Power Awning Manuel d'utilisation et d'entretien

Lippert Components

Lippert Components Jack-It Manuel utilisateur

Lippert Components

Lippert Components Ground Control 2.0 Manuel utilisateur

Lippert Components

Lippert Components Solera Classic Instructions d'installation

Lippert Components

Lippert Components X-Trek Manuel utilisateur

Lippert Components

Lippert Components ground control TT Instructions d'installation

Lippert Components

Lippert Components COACH STEP Guide de configuration

Lippert Components

Lippert Components Ground Control 3.0 Landing Gear Manuel utilisateur

Lippert Components

Lippert Components SURESHADE POWER BIMINI Manuel utilisateur

Lippert Components

Lippert Components Solera Power Awning Manuel d'utilisation et d'entretien

Lippert Components

Lippert Components In-Wall Slide-Out Manuel utilisateur

Manuels Accessoires automobiles populaires d'autres marques

James Baroud

James Baroud Odyssey Manuel utilisateur

Motorola

Motorola i50sx Manuel utilisateur

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manuel utilisateur

Feniex

Feniex T3 Manuel utilisateur

Renault

Renault 77 11 423 180 Manuel utilisateur

Kia

Kia E8300-4D000 Manuel utilisateur

Brink

Brink 756843 Manuel utilisateur

Whispbar

Whispbar K085W Manuel utilisateur

v.link

v.link CI-VL2-PC-HSD Manuel utilisateur

Viking

Viking Stack-Rack Guide de configuration rapide

Aries

Aries 203015 Manuel utilisateur

Choetech

Choetech AT0005 Manuel utilisateur

ZZ2

ZZ2 ZZAIR-PRO Manuel utilisateur

Holman

Holman 4A80L Manuel utilisateur

Thule

Thule 2075 Manuel utilisateur

Motorola

Motorola T325 Manuel utilisateur

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guide d'installation

DV8

DV8 FBJL-02 Manuel utilisateur