Lippert Components Solera Manuel utilisateur

Rev: 02.25.2016 Page 1 Solera Power Awning with LED Lights Installation Manual

Solera® Power Awning

with LED Options

OEM INSTALLATION MANUAL

Rev: 02.25.2016 Page 2 Solera Power Awning with LED Lights Installation Manual

Prior To Installation

NOTE: All screws/rivets supporting awning assembly MUST have a backer within the structure of the wall of

the coach.

Awning With LED In Roll Tube Installation

1. Insert drive head pin (Fig. 1A) into end cap (Fig. 1B). Align holes and secure with waxed screw. Insert

screw fully, but do not over-tighten. Repeat process for idler head at other end.

NOTE: Be sure to align LED light wires (Fig. 2A or 3A) coming from idler head with the LED light on roll tube

(Fig. 2B or 3B).

Tools Required

• Electric screw gun

• #2 square screwdriver bit

• ⁄” nut driver bit and/or rivet gun

Resources Required

• Three people

2. Connect the plug from the idler head (Fig. 2A or 3A) to the plug from the LED light (Fig. 2B or 3B) on

the roll tube.

3. Station a person at each end of the awning assembly to hold the support arms. A third person will line

up the fabric cord with the previously-installed awning rail. Slide the fabric cord to desired position.

4. Set the awning assembly to the desired height and attach it to the side of the coach with four #14 x 1

½” screws (286576) at the top (Fig. 4) and two #14 x 1 ½” (286576) screws at the bottom (Fig. 5).

5. Extend the awning half way out by connecting the power and ground wires of the awning to a 12-18V

battery.

6. Secure the middle of the wall mounting channel with two #14 x 1 ½” screws (286576) at any of the

three locations shown (Fig. 6).

Fig. 1 Fig. 2 - Old Connection

286576 286576

Possible screw

/ rivet locations

Fig. 3 - New Connection

Fig. 4 Fig. 5

Fig. 6

Rev: 02.25.2016 Page 3 Solera Power Awning with LED Lights Installation Manual

7. Repeat this process for the other side of awning assembly.

NOTE: Four rivets with ⁄" grip range can be used in place of the two middle and two lower screws on

laminated walls.

8. Take the LED power wire that is already fed through the idler leg and connect to the desired power

wire from the coach.

NOTE: Be sure the black wire is connected to a ground and the red wire is connected to a 3 amp max fuse

and then a power source from the coach.

NOTE: Extend and retract the awning one or two times to ensure that it is square before setting the screws.

9. Attach fabric cord to awning rail with two screws #6-20 x ½" hex to prevent lateral movement.

10. Seal all wall penetrations to protect against water intrusion.

NOTE: All screws/rivets supporting the awning assembly MUST have a backer within the structure of the

wall of the coach.

NOTE: Solera® awnings under 21' in length DO NOT require the use of a cradle.

LED Light Rail Installation

NOTE: Solera® Power Awning MUST be installed prior to LED Light Rail installation.

1. Mount the LED light rail track (Fig. 7B) directly below the awning rail (Fig. 7A) and secure to the side of

the coach.

2. Route the light wire over the top of the awning mount leg and run the light wire down through the leg

in the same manner as the motor wire (Fig. 8).

3. Cut wire to desired length and connect to the coach wiring, making sure to connect the red wire on

the light side to the power wire on the coach side.

NOTE: The LED light rail MUST be wired through a 3 amp (maximum) fused circuit.

4. Connect the black wire on the light to the ground on the coach side.

5. Make sure to seal the light track where it is screwed to the wall and where the light wire connects to

the coach wire.

6. Turn the light on to confirm it illuminates.

Fig. 7 Fig. 8

The contents of this manual are proprietary and copyright protected by Lippert Components, Inc. (“LCI”).

LCI prohibits the copying or dissemination of portions of this manual unless prior written consent from an

authorized LCI representative has been provided. Any unauthorized use shall void any applicable warranty.

The information contained in this manual is subject to change without notice and at the sole discretion of LCI.

Revised editions are available for free download from www.lci1.com.

Please recycle all obsolete materials.

For all concerns or questions, please contact

Lippert Components, Inc.

Ph: (574) 537-8900 | Web: lci1.com | Email: [email protected]

Rev: 02.25.2016 Page 4 Solera Power Awning with LED Lights Installation Manual

Autres manuels pour Solera

Table des matières

Autres manuels Lippert Components Accessoires

Lippert Components

Lippert Components Solera Manuel utilisateur

Lippert Components

Lippert Components Solera Manuel utilisateur

Lippert Components

Lippert Components Solera Smart Arm Instructions d'installation

Lippert Components

Lippert Components Solera Instructions d'installation

Lippert Components

Lippert Components Solera Manuel utilisateur

Lippert Components

Lippert Components Solera Power Awning XL Manuel utilisateur

Lippert Components

Lippert Components Solera Power Awning Manuel utilisateur

Lippert Components

Lippert Components Solera Classic Awning Manuel utilisateur

Lippert Components

Lippert Components Solera TI-278 Instructions d'utilisation et d'entretien

Lippert Components

Lippert Components Solera Manuel utilisateur

Lippert Components

Lippert Components Awnbrella Instructions d'installation

Lippert Components

Lippert Components Solera Slide Topper Instructions d'installation

Lippert Components

Lippert Components Solera Classic Awning Manuel d'utilisation et d'entretien

Lippert Components

Lippert Components Solera Manuel utilisateur

Lippert Components

Lippert Components Solera Classic Manuel utilisateur

Lippert Components

Lippert Components Solera Smart Arm Manuel utilisateur

Lippert Components

Lippert Components Solera Instructions d'installation

Lippert Components

Lippert Components Solera Manuel utilisateur

Lippert Components

Lippert Components Solera Manuel utilisateur

Lippert Components

Lippert Components Solera Classic Instructions d'installation

Lippert Components

Lippert Components Solera Manuel utilisateur

Lippert Components

Lippert Components Solera 3000WS Series Manuel utilisateur

Lippert Components

Lippert Components 2021130659 Instructions d'installation

Lippert Components

Lippert Components SURESHADE ATF Guide de démarrage rapide

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur