Lionel Pylon Manuel utilisateur
Lionel
Pylon
Owner’s Manual
Lionel
Pylon
Owner’s Manual
78-5309-250
2/18
Thank You!
T
hank you for your purchase of the Lionel Pylon! This manual will cover installation of both the
single and double pylons, lighted or non-lighted. This accessory adds action and fun for any
Lionel layout!
2
Plug-Expand-Play®
This revolutionary accessory system simplifies the setup and operation of your
favorite accessories. Plug-Expand-Play®accessories easily connect to your layout
for power using a standardized 3-pin cable that connects directly to a Plug-Expand-
Play®Lock-on track section. Separate control boxes that are necessary for control
of some accessories also use the easy-to-use cable system. Many multi-operation
accessories utilize a standardized 6-pin control cable, and there are separate-sale
cables that allow you to expand your system to meet your needs. More complicated
wiring necessary on older accessories is simplified with the new standardized cable
system fitted on every Plug-Expand-Play®accessory.
The following Lionel marks are used throughout this Owner’s Manual and are protected under law.
All rights reserved.
Lionel®, TMCC®, LEGACY®, LEGACY® Control System, FasTrack®, Lockon®, Plug-Expand-
Play®, CAB-1®Remote Controller, Accessory Switch Controller™, ASC™
Assembling a single pylon 4
Assembling a double pylon 4
Connecting power to the Plug-Expand-Play accessory 5
Connecting your accessory to FasTrack 6
Connecting your accessory to tubular track 7
Connecting your accessory to a transformer 8
Wiring for TMCC or LEGACY 9
SC-2 wiring and operation 9
ASC and ASC2 wiring and operation 10
Replacing the lamp in a lighted pylon (if applicable) 11
Lionel Limited Warranty Policy & Service 12
Table of Contents
3
4
Assembling a single pylon
Assembling a double pylon
Complete the assembly of your Pylon by attaching the included figure and support rod to
the structure. Figure 1a illustrates the following procedure.
1. Note that the supporting rod has different shaped ends. Insert the D-shaped coupling bot-
tom end of the support rod onto the D-shaped mounting post on the top of the pylon. Refer
to the diagram for further assistance.
2. Insert the D-shaped top end of the rod into the D-shaped opening in the bottom of the fig-
ure.
Complete the assembly of your double pylon by attaching the included figures and their
support rods to the structure. Figure 1b illustrates the following procedure.
1. Note that the supporting rods have different shaped ends. Insert the flattened ends of the
support rods into the tubes protruding from the top of the pylon. Refer to the diagram for
further assistance.
2.Insert the D-shaped ends of the wires into the openings in the bottom of the figures.
Once your accessory is wired, the base is secured, and the figures are attached, you are
clear for takeoff!
Figure 1a. Installing the support rods on a single pylon
Figure 1b. Installing the support rods on a double pylon
D-shaped coupling sup-
port rod (bottom)
D-shaped mounting
post on top of pylon D-shaped
support rod (top)
D-shaped mount-
ing hole, bottom of
figure
Rear of figure
Front of figure
5
Connecting power to the Plug-Expand-Play accessory
Figure 2. Plug-Expand-Play wiring
Lock-on Power Block
Lock-on
3-pin male
connector
3-pin male
connector
3-pin male
connector
OR
Your Plug-Expand-Play accessory connects to either a Plug-Expand-Play lock-on
(6-81313) or a Plug-Expand-Play power block lock-on (6-81314) with the 3-pin male
connector that is attached to its base. Simply plug this connector into the lock-on and apply
track power. To turn the accessory OFF, unplug the 3-pin connector from the lock-on or turn
off the track power. See figure 2 for wiring.
Auxiliary Power Supply
(optional)
You also are able to connect your accessory to FasTrack using the 8" 3-pin female pigtail
cable (available separately, 6-82038). Plug in the 3-pin male connector on the accessory
into the 3-pin female slot on the 3-pin female pigtail. Then attach the red wire to the inside
rail and the black wire to the outside rail.
Connecting your accessory to FasTrack
3-pin male
connector
3-pin female
connnector
FasTrack
Underside of FasTrack
Red wire
Black
wire
Figure 3. Connecting your accessory to FasTrack
Note The white wire is not used when connecting your accessory to FasTrack.
8" 3-pin female pigtail
(6-82038)
6
Connecting your accessory to tubular track
You can also connect your accessory to tubular track using the 8" 3-pin female pigtail
cable (available separately, 6-82038). Plug in the 3-pin male connector on the accessory
into the 3-pin female slot on the 3-pin female pigtail. Then attach the red wire to the inside
rail position of the universal lock-on (6-24213) and the black wire to the outside rail position.
Note The white wire is not used when connecting your accessory to tubular track.
Tubular track Universal lock-on
Red wire
Black wire
3-pin male
connector
3-pin female
connector
Figure 4. Connecting your accessory to tubular track.
8" 3-pin female pigtail
(6-82038)
7
120/60z
U
0~18VAC
AB
U
0~18VAC
U
0~18VAC
AB
U
0~18VAC
TRACK ACCESSORY
Connecting your accessory to a transformer
To power your accessory using a CW-80 Transformer (6-14198), or any other transformer,
you will need the 8" 3-pin female pigtail cable (available separately, 6-82038)to connect
to the transformer terminals. Make sure that all connections are secure. Loose connections
can produce extremely high temperatures. For this reason, do not touch the terminals or
track connections during use. Also, do not locate scenery materials such as lichen or ground
foam near the terminals.
1. Plug in the 3-pin male connector on the accessory to the 3-pin female slot on
the pigtail.
2. Loosen the red ACCESSORY thumbscrew terminal, then place the red wire on
the metal terminal bar. Still holding the wire end, tighten the red thumbscrew
until secure. Be sure that the wire is touching the metal post.
3. Loosen the black ACCESSORY thumbscrew terminal, then place the black
wire on the metal terminal bar. Still holding the wire end, tighten the black
thumbscrew until secure. Be sure that the wire is touching the metal post.
4. Plug the CW-80 Transformer into your wall outlet (120 volts).
5. Apply 18 volts of power by raising the orange throttle on the transformer.
3-pin male
connector
3-pin female
connector
Transformer
Figure 5. Connecting your accessory to a transformer.
Red wire
Black
wire
8" 3-pin
female
pigtail
(6-82038)
8
Wiring for TMCC or LEGACY
To power your accessory in the Command Control and LEGACY environments, you will
need an SC-2 (6-22980), an ASC (6-14182), or an ASC2 (6-81639). You will also need an
8" 3-pin female pigtail (available separately, 6-82038) and a transformer (6-14198).
Note Refer to your CAB-1, CAB-1L, or LEGACY manual for remote instructions.
SC-2 wiring and operation
Three wires are needed to connect your accessory to the SC-2 and a separate accessory trans-
former.
1. Attach a wire to the transformer Common/Ground/U terminal and connect it to the COMM
(common) position on the SC-2.
2. Connect the black wire of the pigtail to the AUX2 terminal on the SC-2.
3. Connect the red wire of the pigtail to the transformer Power/A terminal.
4. Press Aux2 to turn the accessory on. Pressing Aux2 again will turn it off.
ACC3 ACC4
ACC1 ACC2
SC-2
Black wire
Red wire
Transformer
3-pin male
connector
3-pin female
connector
Figure 6. Wiring an SC-2.
8" 3-pin female
pigtail (6-82038)
9
ASC and ASC2 wiring and operation
Three wires are needed to connect your accessory to the ASC/ASC2 and a separate accessory
transformer.
1. Attach a wire to the transformer Common/Ground/U terminal and connect it to the COMM
(common) position on the ASC/ASC2.
2. Connect the black wire of the pigtail to the Accessory 2 terminal on the ASC/ASC2.
3. Connect the red wire of the pigtail to the transformer Power/A terminal.
4. Press Aux2 to turn the accessory on. Pressing Aux2 again will turn it off.
AU
3-pin male
connector
3-pin female
connector
Transformer
ASC/ASC2
Black wire
Red wire
Figure 7. Wiring an ASC/ASC2.
8" 3-pin female pigtail
(6-82038)
10
Table des matières
Autres manuels Lionel Jouet
Lionel
Lionel 0-6-0 Docksider Manuel utilisateur
Lionel
Lionel K-LINE EP-5 Manuel utilisateur
Lionel
Lionel Alco PA-1 Manuel utilisateur
Lionel
Lionel 4-6-2 Pacific Manuel utilisateur
Lionel
Lionel Santa's Christmas Wish Station Manuel utilisateur
Lionel
Lionel 193 Manuel utilisateur
Lionel
Lionel Caboose with Deck Manuel utilisateur
Lionel
Lionel 313 Manuel utilisateur
Lionel
Lionel Passenger Station Manuel utilisateur
Lionel
Lionel 6-16706 Manuel utilisateur
Lionel
Lionel Pennsylvania K-4 Freight Ready-To-Run O Gauge... Manuel utilisateur
Lionel
Lionel 87-1811020 Manuel utilisateur
Lionel
Lionel Union Pacific RS-3 Manuel utilisateur
Lionel
Lionel Scout Set Manuel utilisateur
Lionel
Lionel 6-29366 Manuel utilisateur
Lionel
Lionel 616 Flying Yankee Manuel utilisateur
Lionel
Lionel Thomas & Friends Manuel utilisateur
Lionel
Lionel USRA 0-8-0 Steam Locomotive and Tender Manuel utilisateur
Lionel
Lionel GP-20 Manuel utilisateur
Lionel
Lionel Building Set Manuel utilisateur
