Lionel Baby Toy Manuel utilisateur

73-0054-250

7/06

Rev. 1

Walter E. Disney Limited

Ready-to-Run Set

Owner’s Manual

CAUTIO —ELECTRIC TOY

OT RECOMME DED FOR CHILDRE U DER EIGHT YEARS OF AGE. AS WITH

ALL ELECTRIC PRODUCTS, PRECAUTIO S SHOULD BE OBSERVED DURI G

HA DLI G A D USE TO PREVE T ELECTRIC SHOCK.

TRANSFORMER RATINGS—I PUT: 120 VAC; 60 HZ O LY.

AC OUTPUT: 18 V; 30 VA

©Disney

Walter E. Disney Limited

Ready-to-Run Set

Owner’s Manual

Cong atulations!

Congratulations on your purchase of the ready-to-run Walter E. Disney Limited Train Set!

This set features everything you need to get started—a PowerMax Transformer, a huge loop

of easy-to-assemble FasTrack track, a string of detailed cars, and a powerful Lionel locomotive.

Have fun growing with this complete train set! Start with the set components, then follow

your imagination into your own miniature world. Expand your railroad empire with addition-

al FasTrack track sections, enhance your layout with accessories, lengthen your consist with

extra cars, or operate a new locomotive at the head end of your train! Explore the possibilities

at your authorized Lionel dealer.

Use this Owner’s Manual to learn how to set up, operate, and maintain your train set for

years of reliable operation.

The transformer included with this set should be periodically

examined for conditions that may result in the risk of fire,

electric shock, or injury to persons (such as damage to the

output cord, blades, housing, or other parts). In the event that

such conditions exist, the transformer should not be used until

properly repaired.

arents!

Train Set Features

• Bright headlight

• Puffing smoke

• Air whistle

• Forward-Neutral-Reverse operation

• Opening boxcar doors

• Operating couplers

The following Lionel marks may be used throughout this instruction manual and are protected under

Lione ®, TrainMaster®, Odyssey®, Rai Sounds®, CrewTa k™, TowerCom™, DynaChuff™,

StationSounds™, Pu mor®, E ectroCoup er™, Magne-Traction®, CAB-1®Remote Contro er,

PowerMaster®, Lione ZW®, ZW®, PowerHouse®, TMCC®, Lione vi e™, Lockon®, Wire ess Tether™,

LionMaster®, FatBoy™, American F yer®, TrainSounds™, PowerMax™

The name FasTrack®is used with permission from Pitsco, Inc.

Train Set Inventory

• 4-4-0 Steam locomotive and tender

• Boxcar

• Gondola

• Work caboose

• PowerMax Transformer with accessory wire

• Three straight FasTrack track sections

• Eight curved FasTrack track sections

• One straight FasTrack terminal track section

• Smoke fluid

• Replacement traction tire

• Owner’s Manual

Table of contents

C eating you layout

Operating your PowerMax Transformer safely 4

Building your Lionel layout 5

Joining the FasTrack track sections 6

Wiring your PowerMax Transformer 7

Running you t ain

Running your train set 8

Adding smoke fluid to your locomotive’s smoke generator 9

Coupling 9

Operating your train with the PowerMax Transformer 10

Experiencing the features of the PowerMax Transformer 11-12

Reverse unit procedure 13

Powe Max T ansfo me ope ation

Powering your layout with the PowerMax Transformer 14

Maintaining and se vicing you set

Lubricating your locomotive 15

Replacing your locomotive’s traction tire 16

Replacing your locomotive’s headlamp 16

Replacing the lamp in your work caboose 17

Advanced connections: powering two isolated blocks with two transformers 18

Troubleshooting 19

Limited Warranty/Lionel Service 20

Operating your owerMax Transformer safely

Your Lionel PowerMax Transformer is listed by Underwriter’s Laboratory Inc. and has been

carefully designed to ensure peak performance. When using electrical products, basic

safety precautions should be maintained.

Be sure to observe the following guidelines:

• Read the manual thoroughly before using this device.

• This device is not recommended for children under eight years of age.

• Parents should periodically inspect this product for potential hazards and, if necessary,

have them repaired by an authorized Lionel Service Center. In the event that such a condi-

tion exists, the transformer should not be used until it has been properly repaired.

• The PowerMax Transformer is intended to be used indoors. Do not use this device if water

is present. Serious or fatal injuries may result.

• Use the PowerMax Transformer only for its intended purpose.

• The PowerMax Transformer was meant to operate on 120-volt, 60-Hertz power. Do not con-

nect this product to any other power supply.

• Do not operate the PowerMax Transformer with a damaged cord, plug, or case.

• To avoid the risk of electrical shock, do not disassemble the unit. There are no user service-

able parts inside. If damaged, take this product to an authorized Lionel Service Center.

• Do not operate the PowerMax Transformer on your layout unattended. Obstructed acces-

sories or stalled trains may overheat, resulting in damage to your layout.

• Always unplug the PowerMax Transformer from the power source when not in use.

• Never insert objects into the ventilation slots on this product. Damage to sensitive

electronic components can result.

C eating you layout

Building your Lionel layout

Your set comes with eight curved, three straight, and one terminal section of track. Figure 1

provides some examples of layouts that you can build with these track sections.

By adding more FasTrack track sections, you can create an endless number of exciting

track arrangements for more fun, action, and variety. The railroad empire of your dreams can

quickly become a reality!

C eating you layout

Figure 1. Track layout ideas

Figure 2. Add-on Track Pack layouts

FasTrack Add-on Track Packs make it easy to expand your railroad. Each Track Pack

includes all the track sections you need to create a more advanced layout using the sections

included with this set. Refer to Figure 2 to explore the possibilities.

Inner Passing Loop Add-on Track Pack

6-12028

Figure 8 Add-on Track Pack

6-12030

Outer Passing Loop Add-on Track Pack

6-12031

Siding Track Add-on Track Pack

6-12044

Track acks available separately.

Joining the FasTrack track sections

FasTrack track sections join together easily. With interlocking roadbed sections and large

rail tabs, the track fits together securely so you always get good electrical contact. Take a

look at Figure 3 to see how to join the track sections.

1. Line up your two sections of track.

2. Insert the rail tabs into the openings at the ends of the corresponding

rails.

3. Press the sections together until the interlocking roadbed snaps into

place.

Figure 3. Joining the track sections

C eating you layout

Rail tab

Wiring your owerMax Transformer

C eating you layout

Connect your FasTrack terminal section to the PowerMax Transformer. Use the wires that

are already attached to the terminal section. Make sure that all connections are secure.

Loose connections can produce extremely high temperatures. For this reason, do not touch

the terminals or track connections during use. Also, do not locate scenery materials such as

lichen or ground foam near the terminals.

1. Feed the wires through the notch in the FasTrack terminal section. Refer to

Figure 4.

2. Loosen the red TRACK thumbscrew terminal, then slide the spade-shaped

connector on the red wire into position. The thumbscrew post should be

positioned between the “blades” of the spade connector. Be sure that the blades are

touching the metal post. Tighten the thumbscrew to secure the connection.

3. Loosen the black TRACK thumbscrew terminal, then slide the spade-

shaped connector on the black wire into position. Tighten the thumbscrew to

secure the connection. Be sure that the blades are touching the metal post. Tighten the

thumbscrew to secure the connection.

4. Plug the PowerMax Transformer into your wall outlet (120 volts).

As your layout expands, you may also make power connections with the stripped ends of

wires, placing no more than two wires on each terminal. For best performance on large

layouts, it is recommended that you use 16-gauge wire to connect your PowerMax

Transformer to the track. On larger layouts where several track connections are required, the

use of separate junctions/terminal strips (available at your local electronics store) is

recommended to prevent voltage drops.

To prevent the excessive build up of heat, be sure to select the proper wire gauge

for your layout. Track connections must be made with 18-gauge wire or heavier.

Larger layouts require a minimum of 16-gauge wire.

Caution!

U120/60z

0~18VAC 

TRACK

Figure 4. Controller connections

FasTrack terminal section

otch

Spade-shaped

connector

Running you t ain

Running your train set

With t ack powe off, place you t ain set on the t ack.

Refer to page 9 for information on coupling the cars.

Powe up you locomotive with you t ansfo me .

our locomotive is designed to operate on 7-15 volts alternating cur-

rent. Virtually all Lionel and Lionel-compatible alternating-current transformers

are suitable.

Do not power your locomotive with direct-current (DC) transformers.

The locomotive was designed for use with alternating-current (AC)

transformers only.

Move ‘em out!

Get your locomotive moving. Your locomotive goes through a repeating pattern

of operations: forward, neutral, reverse, neutral, and so on. To sequence the reverse

unit, press the DIRECTION button on your transformer, or briefly bring the throttle

all the way back to the OFF position and then forward. Each press of the DIRECTION

button or interruption in track power causes the locomotive to advance to the next

operational state.

Adjust track voltage until your locomotive moves at your desired speed.

Connect the d awba between the locomotive and tende .

See Figure 5.

If the smoke unit switch is in the ON position, add smoke fluid to your

locomotive’s stack to prevent damage to the smoke unit. Refer to

page 9 for additional information.

Caution!

Note!

Figure 5. Drawbar connection

Coupling

When coupling your cars, at least one of the mating couplers must be open as shown at the left

in Figure 6. Press down on the lock release to open the coupler, then push the cars toward

each other until they lock together.

eep in mind that it’s easier to couple cars on a straight stretch of track.

Lock release

Figure 6. Coupler operation

Note!

Running you t ain

Adding smoke fluid to your locomotive’s smoke generator

Your locomotive is equipped with a smoke generator that produces safe, clean white smoke

during operation if the smoke unit switch is in the ON position. Refer to Figure 8 on

page 13 for the location of the switch.

The smoke generator requires the periodic addition of Lionel smoke fluid in order to function.

A small bottle of smoke fluid is included with this set. Press down and unscrew the cap. Pierce the

tip on the nozzle. Add about four drops of fluid directly into the locomotive’s stack. Smoke pro-

duction commences momentarily. It will start faster if you run your locomotive at higher speeds.

When smoke production decreases, add more fluid (about four drops). An idle locomotive will

not smoke.

Smoke production is greater at higher voltages and when the locomotive is pulling a heavy

load or a long consist.

Caution! When the smoke unit switch is in the ON position, always keep a small amount

of smoke fluid in the locomotive’s smoke generator; the generator’s element

can become damaged if operated without smoke fluid. This is particularly true

if your locomotive sits in neutral for an extended period of time without smoke

fluid in the generator.

If you prefer to operate the locomotive without smoke or you do not want to add

smoke fluid, slide the smoke unit switch to the OFF position.

Note!

Operating your trains with the owerMax Transformer

You’re clear for departure! Move the throttle control handle forward to increase power to

the track. The farther forward you push the handle, the faster your train will go.

Quickly shutting off or throwing the throttle all the way forward will not result in

an instant change in track voltage.

When operating in the conventional (non-Command) environment, remember that the

greater the load on the engine (adding more cars for the engine to pull, for example), the far-

ther forward the handle must be pushed before it will operate the locomotive.

Note!

Running you t ain

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Lionel Jouet

Lionel

Lionel Tinplate 392 Steam Locomotive Manuel utilisateur

Lionel

Lionel GP-7 diesel locomotive Manuel utilisateur

Lionel

Lionel SD70MAC Manuel utilisateur

Lionel

Lionel Nickel Plate Road Super Freight Manuel utilisateur

Lionel

Lionel FlyerChief Berkshire Locomotive and Tender Manuel utilisateur

Lionel

Lionel Glacier Route Freight Ready-To-Run Train Set Manuel utilisateur

Lionel

Lionel 4-8-2 Mohawk Manuel utilisateur

Lionel

Lionel Fastrack 060 Remote Switch Manuel utilisateur

Lionel

Lionel SD-80 Diesel Locomotive Manuel utilisateur

Lionel

Lionel BNSF Ice Cold Express Manuel utilisateur

Lionel

Lionel 4-6-2 Pacific Manuel utilisateur

Lionel

Lionel 238E Torpedo 4-6-2 steam locomotive Manuel utilisateur

Lionel

Lionel Pennsylvania Flyer Deluxe Manuel utilisateur

Lionel

Lionel Playground Swings Manuel utilisateur

Lionel

Lionel Century Club II Niagara Milk Manuel utilisateur

Lionel

Lionel Railroad Tugboat Manuel utilisateur

Lionel

Lionel Plug-Expand-Play Manuel utilisateur

Lionel

Lionel Union Pacific RS-3 Manuel utilisateur

Lionel

Lionel FasTrack 78-2110-250 Manuel utilisateur

Lionel

Lionel Pennsylvania ALCo A-A Set Manuel utilisateur

Lionel

Lionel The Polar Express Manuel utilisateur

Lionel

Lionel 3376 Manuel utilisateur

Lionel

Lionel TrainMaster Command-equipped F3 diesel locomotive B... Manuel utilisateur

Lionel

Lionel SD-80 Diesel Locomotive Manuel utilisateur

Manuels Jouet populaires d'autres marques

marklin

marklin 37321 Manuel utilisateur

Canon

Canon PAPER CRAFT Manuel utilisateur

GREAT PLANES

GREAT PLANES Pitts M-12S Manuel utilisateur

NOCH

NOCH 14261 Manuel utilisateur

Hausler

Hausler 450 SE V2 Manuel utilisateur

Dynaflite

Dynaflite Daydream Manuel utilisateur

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuel

Kenner

Kenner Batman 63651 Manuel utilisateur

LEGO

LEGO 8527 Manuel utilisateur

iKarus

iKarus ECO 8 Manuel utilisateur

Multiplex

Multiplex EasyStar II Mode d’emploi

Walkera

Walkera 38 Mode d’emploi

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuel utilisateur

MD MXION SWD Manuel utilisateur

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuel utilisateur

marklin

marklin 39671 Manuel utilisateur

Meccano

Meccano 15103 Manuel utilisateur

LEGO

LEGO TECHNIC 8735 Manuel utilisateur