Lionel 3376 Manuel utilisateur

71-9846-250

5/98

Lionel 3376

Andy the Lionel Giraffe

Animated Figure

Transport Car With CarSounds

Owner’s Manual

Table of contents

Congratulations! Transformer operations

Congratulations! You now own the

most sophisticated, fun and enter-

taining animated animal transport cars

ever built—the Lionel TrainMaster™

Command-equipped Carsounds

Animated transport car.

From the crisp detail and expert deco-

ration on the outside to the advanced

technology inside, your Lionel CarSounds

animated transport is ready for duty on

your model railroad.

Read this instruction manual thor-

oughly for important tips on operating

and maintaining your CarSounds™ ani-

mated transport. When properly cared

for, it will last a lifetime. Experience the

superiority of today’s Lionel.

• Lionel CommandTM R2LC unit for use

with the Lionel TrainMaster®

CommandTM model railroad control

system

• CarSoundsTM sound system—

digital samples from our old friends

in California.

• Die-cast ElectrocouplersTM

• Stamped metal frame.

• Die-cast trucks.

Transformer operations

Running your CarSounds Transport car with a Lionel transform-

er 3

Tell-Tale and ramp installation 4

Using your CarSounds ’s ElectrocouplersTM 6

Your CarSounds’s Railsounds system—the basics 6

Notes on CarSounds 6

TrainMaster Command operations

The Command control environment 7

Running your CarSounds animated transport in the

TrainMaster Command environment 8

CAB-1 commands for your CarSounds animated transport 8

CAB-1 numeric keypad commands for your CarSounds

animated transport car 9

Tuning your CarSounds animated transport’s performance 10

Assigning your CarSounds animated transport a new ID# 11

Advanced TrainMaster Command operations 12

Volume and reverse unit switch location CarSounds

animated transport car 14

Maintaining and servicing your CarSounds™ animated trans-

Congratulations! Transformer operations

Running your CarSounds animated transport car with a Lionel

Place your CarSounds animated transport car

on Lionel or Lionel-compatible O gauge

• For the best operation of your CarSounds animated transport car, have

the animated figure facing towards the front.

2Power up your CarSounds animated trans-

port car with your transformer.

• Your CarSounds animated transport car is designed to operate on 7-18

volts alternating current. Virtually all Lionel and Lionel-compatible alter-

nating-current transformers are suitable; we recommend the

TrainMaster Command model railroad control system.

•

Donot power your

CarSounds animated transport car

with Direct current

(DC). Damage to sensitive electronic components may occur.

• When you first power up your track, the CarSounds animated transport

car will wait between 3 and 8 seconds as it “listens”for digital language

from the TrainMaster Command Base (available separately). When it’s

determined that it’s on a conventional (nonCommand) railroad, a

CarSounds transport car animal sound will occur.

3Move ‘em out!

• Get your CarSounds animated transport car moving, place it somewhere

within the train consist. As your train moves along, any stop will pro-

duce an animal sound automatically.

• WSTL/HRN (longer than 4 sec) while car is in motion - giraffe says,

“Yipee!”

• WSTL/HRN (longer than 4 sec) while car is at rest - giraffe says, “Wow!

That was loud!”, or,“Wow! Railsounds forever!”

• When the car has stopped after motion - giraffe says one of the following:

“All clear ahead!”, “All clear to York, Pennsylvania!”, “All clear to Lionelville!”,

“All clear to Lionel City!”

• Crossing the linear ramp along the track, lever on car drops Andy - car

makes crashing sounds, giraffe says nothing, or one or more of the fol-

lowing: “Oh no!”, “All clear ahead!”, “That was a close one!”

• You must install the telltale and ramp, for your animated figure to duck

in the non-command environment.

Tell-tale and ramp installation

Figure action

Tell-tale assembly

Tell-tale and ramp installation

Andy the Lionel giraffe rides in the

Lionel #3356 Africa Transport Stock

Car. Andy is a lively participant on your

layout. His vantage point, high above the

rest of the train, allows him to see clear

track ahead and he lets the engineer

know. Lets install the tell-tale and ramp

and get Andy “ducking”.

Tell-tale pole

Extension rod

Tell-tales

End retainer

Insert the knurled end of the extension

rod into the hole in the horizontal brace

of the pole, pressing it firmly in place.

Next slide the 12 tell-tales onto the exten-

sion rod. Finaly press the retainer onto the

end of the extension rod to hold the tell-

tales in place.

Tell-tale and ramp installation

Figure action

Tell-tale assembly

Tell-tale base and ramp assembly

Tell-tale and ramp installation

Assembled tell-tale pole

signal base

notches

End prongs

cam plate

2) Place the cam plate centered

over the signal base with the end

prongs faced in toward the track

rail.

3) Put end prongs against side of track and

press the two center notches on the cam plate

into the openings on the signal base. To lock

the cam plate, pull it sideways into the chan-

nels. 1) Place hooks over flange of outside rail,

then pull base until notch slips over flange

on inside rail.(0 or 027 gauge)

4) Insert the assembled tell-tale

pole onto the signal base with the

tall-tales hanging over the track.

The signal base may be clamped to any straight track. If placed next to

a curved track, it must be faced so that the pole is on the INSIDE of the

curve.

Notes on Railsounds

• Use the volume control knob on the

underside of the CarSounds animated

transport to adjust sound output. (See

page 15 for its location.)

• For even more fantastic

Railsounds effects, operate in the

TrainMaster Command environment.

Your CarSounds™ animated transport’s Railsounds system—the

Lionel Railsounds is the most fantas-

tic model railroad sound system in

the world. Your CarSounds animated

transport features digital recordings,

for the most fun in model railroading.

Apply track power and the CarSounds

animated transport delivers a reper-

toire of sounds. This occurs at start up,

and every time you stop the train, or

use the horn.

Transformer operations

Using your CarSounds™ animated transport’s Electrocouplers in the non-Command

To use your CarSounds animated trans-

port’s Electrocoupler in the non-Com-

mand environment, you must first couple

a piece of rolling stock equipped with

Lionel magnetic couplers directly to your

CarSounds animated transport. The mag-

netic coupler on the rolling stock will then

react to the magnetic field generated by a

Lionel remote-control track section (avail-

able separately). Place your rolling stock’s

coupler “trigger disc”over the central coil

of a remote-control track section and press

uncouple on the controller. The magnetic

field pulls the disc downward, and the cou-

pler opens.

Your CarSound animated transport

Electrocouplers will NOT open manually

or by using a remote-control track sec-

Magnetic coupler on the rolling stock coupled to

yourCarSounds™animatedtransport

Note!

Remote-control track section

Your CarSounds™ animatedtransport’s Electrocouplerin theTrainMasterCommand

Your Lionel CarSounds animated

transport is equipped with

front and rear Electrocouplers that

respond to the COUPLER F (front)

and COUPLER R (rear) button on

your CAB-1 remote when operated

in the Trainmaster Command envi-

ronment. Simply press either but-

ton on your CAB-1 remote, and that cou-

pler opens.

Your CarSounds™ animated

transport Electrocouplers

are NOT designed to be

opened manually.

Note!

TrainMaster Command opera-

Transformer operations

Using your CarSounds™ animated transport’s Electrocouplers in the non-Command

Your CarSounds™ animatedtransport’s Electrocouplerin theTrainMasterCommand

The Command control environment

Lionel TrainMaster Command is the

advanced model railroad control system

from Lionel.Your CarSounds animated trans-

port is equipped with the Lionel R2LC for coil

coupler and lighting control, and access to

additional Railsounds features. TrainMaster

Command gives you the power to operate

multiple Command-equipped locomotives

on the same track, at the same time.

tooperate in commanD, you neeD acommanD

Base anD acaB-1 remote.

Find them both at

your authorized Lionel retailer.

Place your CarSounds animated transport on

Lionel or Lionel compatible O gauge track.

• Make sure track power is OFF before placing your CarSounds™ animated

transport on the track.

• Make sure your Lionel Command Base is ON and its communications

wire is connected to the COMMON post on your Lionel transformer or

the U post on any of your installed PowerMasters.

• Once positioned on the track, increase track voltage to FULL (on

PowerMaster, slide the CMD/CONV switch to CMD).

2Address your CarSounds animated transport

using CAB-1.

• Press ENG and 1 on the numeric keypad of your CAB-1 remote. This com-

mand is sent by CAB-1 to the Command Base, which then translates your

command into digital code. That code is sent around your railroad’s out-

side rails in the form of a digital “halo.” All Command-equipped Lionels lis-

ten to this digital communication, but they do not respond until they hear

their individual ID number—in this case, “1.”

• The digital language of TrainMaster Command—and not track power—con-

trols the actions of Command-equipped Lionels. Track power is simply like

gasoline in the tank of your car—it gives you the power to go places, but it

doesn’t tell you where to go or how fast to get there.

• All Command-equipped Lionels come factory-programmed with an ID# of

“1.”To change the ID# of your CarSounds animated transport (equipped

with an R2LC, designed to control coil couplers, and Railsounds features),

see page 11.

3Move ‘em out!

• Throttle up or press any command button on CAB-1. Your CarSounds ani-

mated transport will respond to your every command. Read on.

TrainMaster Command opera-

Activates keypad (see page

9).

Press HALT to shut down all

Power-Master electrical out-

put on your railroad. Stops

all Command-equipped

Lionelsinoperation.

CAB-1 commands for your CarSounds animated transport

HALT

PressandholdBRAKE.

squealing Brake sounDs,

crashing sounDs.

(Occurs when train is in motion)

carsounDs animateD trans

port railsounDs effects in

Rearcouplerreleases.

Andy the giraffe ducks

head.

says, “ohno!” anD makes

crashing sounDs.

Frontcouplerreleases.

Your Command-equipped

CarSounds animated transport

comes factory-programmed with an

ID# of “1.”To get your CarSounds™ ani-

mated transport in action, set

PowerMasters to CMD or set all power

supplies on full. Even though it is a“car”,

your CarSounds animated transport is

referred to as an engine in TrainMaster

terminology, so press ENG and “1” on

CAB-1. Turn the throttle or press any

command button; your CarSounds ani-

mated transport set is ready for

Command operations.

address Locomotive #1

PowerMasters set to

CMD or traditional

power supplies ON FULL

Press ENG

Press 1 (the ID#)

TrainMaster Command operations TrainMaster Command operations

Running your CarSounds animated transport in theTrainMaster Command

Press WSTL/HRN (longer than 4

sec) to get Andy excited.

(only when aDDresseD as

engine) - giraffe Ducks, car

makes

coupler sounDs, crashing

sounDs, giraffe says nothing,

or one or more of the follow

ing:“ohno!”,“all clear

while car is in motion - giraffe says,“yipee!”

while car is at rest - giraffe says, “wow! that was louD!”, or, “wow!

TrainMaster Command operations TrainMaster Command operations

 Resets the CarSounds animated

transport.

nosounD

 Raises the volume of R a i l -

sounds.

sounD volume increases.

3 While car is in motion Andy the giraffe

says,“Yipee”

4   Lowers the volume of Rail-

sounds.

sounD volume Decreases.

When you press AUX1 on CAB-

1, you turn the numeric

keypad into 10 command but-

tons. The keypad lets you control

extra command features (until

you press any top-row button

like SW, ACC, RTE, TR, or ENG).

The CAB-1 keypad overlays

included with your CarSounds™ ani-

mated transport are designed to

help you learn the auxiliary fea-

tures specific to this locomo-

tive.

railsounDs sounDs in BolD

italic.

CAB-1 numeric keypad commands for your CarSounds™ animat-

DIESEL

ENGINE

RESET

VOLUME RPM

SHUT

CREW

TALK

TOWER

COM

DOWN

➠

START-UP

Note!

When the car has stopped after motion - giraffe says one of the following:

“All clear ahead!”, “All clear to York, Pennsylvania!”, “All clear to Lionelville!”,

“All clear to Lionel City!”

Crossing the linear ramp along the track, lever on car drops Andy - car

makes crashing sounds, giraffe says nothing, or one or more of the follow-

ing: “Oh no!”,“All clear ahead!”,“That was a close one!”

Tuning your CarSounds™ animated transport’s performance

SOUND QUALITY

To achieve your preferred Rail-

sounds master volume level, use the vol-

ume control knob on the underside of the

CarSounds animated transport (see page

15 for its location). Turn the knob left or

right to adjust the volume to your liking.

For quick remote-control of volume

below the master setting—like muting—

use the CAB-1 numeric keypad’s volume

control. Pressing AUX1 and then 4 on the

numeric keypad lowers overall

Railsounds output.

TrainMaster Command operations TrainMaster Command operations

Autres manuels pour 3376

Ce manuel convient aux modèles suivants

Autres manuels Lionel Jouet

Lionel

Lionel 44 Tonner LionChief Locomotive Manuel utilisateur

Lionel

Lionel FasTrack Grade Crossing with Flashers Manuel utilisateur

Lionel

Lionel Union Pacific Manuel utilisateur

Lionel

Lionel Boom Car Manuel utilisateur

Lionel

Lionel Southern Pacific RS-3 Diesel Freight Manuel utilisateur

Lionel

Lionel The GENERAL 4-4-0 Steam Locomotive Manuel utilisateur

Lionel

Lionel Allegheny Steam Locomotive Manuel utilisateur

Lionel

Lionel LL Bean Ready-To-Run O-27 Set Manuel utilisateur

Lionel

Lionel Wild West Set Manuel utilisateur

Lionel

Lionel C&NW 0-8-0 Manuel utilisateur

Lionel

Lionel FlyerChief Berkshire Locomotive and Tender Manuel utilisateur

Lionel

Lionel 72-4272-250 Manuel utilisateur

Lionel

Lionel 4850TM TRACKMOBILE Manuel utilisateur

Lionel

Lionel American Flyer Manuel utilisateur

Lionel

Lionel 4-4-2 Atlantic Manuel utilisateur

Lionel

Lionel 1563W Wabash Freight Set Manuel utilisateur

Lionel

Lionel Aluminum Passenger Car Manuel utilisateur

Lionel

Lionel American Flyer SD70ACe Manuel utilisateur

Lionel

Lionel Barrel Shed Manuel utilisateur

Lionel

Lionel Early-Era Inspection Vehicle Manuel utilisateur

Lionel

Lionel B&M Paul Revere GP-9 Manuel utilisateur

Lionel

Lionel Crane Car American Flyer Manuel utilisateur

Lionel

Lionel AEC - 57 Switcher Manuel utilisateur

Lionel

Lionel O-27 Santa Fe FT Passenger set Mode d'emploi

Manuels Jouet populaires d'autres marques

marklin

marklin 37321 Manuel utilisateur

Canon

Canon PAPER CRAFT Manuel utilisateur

GREAT PLANES

GREAT PLANES Pitts M-12S Manuel utilisateur

NOCH

NOCH 14261 Manuel utilisateur

Hausler

Hausler 450 SE V2 Manuel utilisateur

Dynaflite

Dynaflite Daydream Manuel utilisateur

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuel

Kenner

Kenner Batman 63651 Manuel utilisateur

LEGO

LEGO 8527 Manuel utilisateur

iKarus

iKarus ECO 8 Manuel utilisateur

Multiplex

Multiplex EasyStar II Mode d’emploi

Walkera

Walkera 38 Mode d’emploi

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuel utilisateur

MD MXION SWD Manuel utilisateur

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuel utilisateur

marklin

marklin 39671 Manuel utilisateur

Meccano

Meccano 15103 Manuel utilisateur

LEGO

LEGO TECHNIC 8735 Manuel utilisateur