Lionel 6-24112 Manuel utilisateur
72-4112-250
8/03
Lionel
Oil Field with Bubble Tubes
Owner’s Manual
CAUTION!The bubble tube contains methylene chloride. Should the tube break, take care
to avoid inhaling or ingesting fumes or liquid. Harmful if swallowed, inhaled or
absorbed through the skin. If swallowed, DO NOT INDUCE VOMITING. Give large quantities of water.
Remove to fresh air. In case of contact with skin or eyes, wash contact area with water for at least 15
minutes. Call a physician immediately. Keep out of the reach of children. In its enclosed state, this liquid
poses no risk.
Congratulations on your purchase of the Lionel Oil Field with Bubble Tubes! This accessory
features an illuminated service shack and seven bubbling “oil” pumps.
The bubble tube contains methylene chloride. Should the tube break, take care to
avoid inhaling or ingesting fumes or liquid. Harmful if swallowed, inhaled or
absorbed through the skin. If swallowed, DO NOT INDUCE VOMITING. Give large
quantities of water. Remove to fresh air. In case of contact with skin or eyes, wash
contact area with water for at least 15 minutes. Call a physician immediately.
Keep out of the reach of children. In its enclosed state, this liquid poses no risk.
Oil Field Inventory
•Oil Field base
•Roof
•Seven bubble tubes with pipe fittings
•Three pipes
•Two green wires
•Owner’s Manual
•Service Center list
2
Table of contents
Powering the accessory 3
Installing the bubble tubes 4-5
Controlling the accessory 6
Controlling the accessory in the Command Control environment 7-9
Replacing the lamps 10-11
Limited Warranty/Lionel Service 12
The following Lionel marks may be used throughout this instruction manual and are protected under law.
All rights reserved.
Lionel®, TrainMaster®, Odyssey®, RailSounds®, CrewTalk™, TowerCom™, DynaChuff™,
StationSounds™, Pullmor®, ElectroCoupler™, Magne-Traction®, CAB-1 Remote Controller®,
PowerMaster®, Lionel ZW®, ZW®, PowerHouse®, TMCC®, Lionelville™, Lockon®
The name FasTrack®is used with permission from Pitsco, Inc.
Caution!
Powering the accessory
While this accessory has an operating range of 12-18 volts (AC), we recommend that you
operate the accessory at 18 volts for the best results. You may choose to power the
accessory with a separate accessory power supply, through a Lionel Lockon (available separately,
6-62900), or a FasTrack Accessory Power Wire (available separately, 6-12053). To make the
proper connections, be sure that the ends of the wires are stripped back 1/8” to 1/4”.
Only an adult should perform this task. We recommend using a pair of wire
strippers. Always use care when stripping wires.
As illustrated in Figure 1, attach a wire to each of the spring clip terminals on the accessory,
then connect the wires to the accessory terminals on the power supply, the spring clip terminals
on the Lockon, or the FasTrack Accessory Power Wires.
To make the spring clip terminal connections, press down on the top portion of the spring
clip so that a metal loop is exposed. Slide the bare end of the wire into the loop, then release
pressure on the spring clip.
For proper operation, set the accessory on a flat, level surface.
3
POWER
SUPPLY
COMMON/GROUND/U
POWER/A
Figure 1. Power connections
Spring clip terminals
Bottom of the accessory
Lionel Lockon
FasTrack connection
To track
or power
supply
Note!
Caution!
OR
UA
OR
Installing the bubble tubes
Each of the bubble tubes is packed separately with a pipefitting and grommet already
attached at the top. As illustrated in Figure 2, the three pipe sections are inserted over the
fittings to create three pairs of bubble tubes. Please note that the pipefitting on one of the
bubble tubes will not receive a pipe section.
4
Figure 2. Bubble tube installation
Pipe section
Pipefitting
Grommet
Bubble
tube
Pump base
Installing the bubble tubes (continued)
Once the pairs are created, position the bubble tubes as illustrated in Figure 3 below. The
bubble tubes are inserted into grommets on the pump bases.
Handle the bubble tubes carefully to avoid breaking the glass and releasing the
fluid. If a break or spill occurs, refer to the caution statement on the cover of this
manual.
5
Caution!
Figure 3. Bubble tube placement
Small pipe
Medium pipe
Large pipe
ON/OFF
switch
6
Controlling the accessory
Rotate the oil drum to turn the bubble tubes on and off. Refer to Figure 4. The lamp inside
the shack is on when the accessory is powered up.
Give the bubble tubes a few minutes to warm up. You may need to increase the
voltage to improve the bubbling. In the rare event that bubbles do not form after
following these steps, gently shake or tap the tubes to agitate the fluid.
Figure 4. ON/OFF switch
OFF ON
Hint!
7
Controlling the accessory in the Command Control environment
For operation in the TrainMaster Command Control environment, you may choose to wire
this accessory with an SC-2 Switch and Accessory Controller (available separately, 6-22980)
or the Accessory Switch Controller (available separately, 6-14182). Refer to these manuals for
additional information.
Be sure that the switch is in the ON position. Refer to Figure 4 on page 6.
Note!
Controlling the accessory in the Command Control environment
(continued)
SC-2 wiring and operation
Three wires are needed to connect the accessory to the SC-2 Switch and Accessory Controller
and a separate accessory transformer. Refer to Figure 5.
1. Attach one wire to the transformer Common/Ground/U terminal and connect it to the
accessory COMM (common) position on the SC-2.
2. Attach a wire to one of the accessory terminals and connect it to the accessory ON/OFF
toggle position on the SC-2.
3. Attach a wire to the other accessory terminal and connect it to the transformer Power/A
terminal.
Use the AUX2 button on your CAB-1 Remote Controller to toggle the accessory
ON and OFF.
8
ACC2 ACC2
ACC1 ACC1
A
U
Figure 5. SC-2 connections
Bottom of the
accessory
Controlling the accessory in the Command Control environment
(continued)
Accessory Switch Controller wiring and operation
Three wires are needed to connect the accessory to the Accessory Switch Controller (ASC) and
a separate accessory transformer. Refer to Figure 6.
1. Attach one wire to the transformer Power/A terminal and connect it to the COMM terminal
on the ASC.
2. Attach a wire to one of the accessory terminals and connect it to a numbered accessory
terminal on the ASC.
3. Attach a wire to the other accessory terminal and connect it to the transformer
Common/Ground/U terminal.
Use the AUX2 button on your CAB-1 Remote Controller to toggle the accessory
ON and OFF.
9
AU
Figure 6. ASC connections
Bottom of the
accessory
Replacing the lamps
The interior of the shack and the bubbles tubes are each illuminated by one lamp, Lionel
part no. 640-9809-300. During the course of normal operations, you may find that the
lamps require replacement. Replacement lamps are available at your authorized Lionel Service
Center or from Lionel Service.
To replace the lamp inside the shack, simply lift off the roof, unscrew the expired bulb, and
install the replacement. Replace the roof when you are done. Refer to Figure 7.
10
Figure 7. Lamp replacement
Table des matières
Autres manuels Lionel Jouet
Lionel
Lionel The Polar Express Manuel utilisateur
Lionel
Lionel Trolley Manuel utilisateur
Lionel
Lionel Snap-On Manuel utilisateur
Lionel
Lionel Dash 9 Diesel Locomotive Manuel utilisateur
Lionel
Lionel F7 A-B-A Manuel utilisateur
Lionel
Lionel Tie Car Manuel utilisateur
Lionel
Lionel American Flyer 2-8-8-2 Steam Locomotive Manuel utilisateur
Lionel
Lionel SD-90 Manuel utilisateur
Lionel
Lionel Hudson 4-6-4 Steam Locomotive Manuel utilisateur
Lionel
Lionel 2343c F-3 A-A Manuel utilisateur
Lionel
Lionel Pennsylvania S-2 Manuel utilisateur
Lionel
Lionel Tinplate 392 Steam Locomotive Manuel utilisateur
Lionel
Lionel Ready-to-Play 2006132 Manuel utilisateur
Lionel
Lionel Holiday Tradition Express Manuel utilisateur
Lionel
Lionel NW2 Manuel utilisateur
Lionel
Lionel Veranda Manuel utilisateur
Lionel
Lionel U.S. ARMY SWITCHER 41 Manuel utilisateur
Lionel
Lionel ZW-L Transformer Manuel utilisateur
Lionel
Lionel Fire Car Manuel utilisateur
Lionel
Lionel SD-40-2 Husky Stack Manuel utilisateur
