Lionel 419R Manuel utilisateur

Lionel

419R Heliport

Owner’s Manual

71-4084-250

8/01

Congratulations on your purchase of the

classic Lionel Heliport! This accessory

features a durable, detail molded structure

with interior illumination and a launching

helicopter that will provide a lifetime of

high-flying action.

The Lionel Heliport is perfect for any

O-27 or O gauge three-rail layout with

12-18 volts (AC) available.

Congratulations

Table of Contents

Wiring your Lionel Heliport for conventional (non-Command) operation 4-5

Operating your accessory in conventional (non-Command) mode 6

Wiring your Heliport with an SC-1 for TrainMaster Command Control operation 6

Wiring your Heliport with an SC-2 for TrainMaster Command Control operation 7

Operating your Heliport with TrainMaster Command Control 8

Installing your Lionel Heliport 9

Launching your helicopter 10

Replacing the lamp in your Lionel Heliport 11

Limited Warranty/Lionel Service 12

The following Lionel marks may be used throughout this instruction manual and are protected under

Lionel®, TrainMaster®, Odyssey™, RailSounds™, CrewTalk™, TowerCom™, DynaChuff™,

StationSounds™, Pullmor®, ElectroCoupler™, Magne-Traction®, CAB-1 Remote Controller®,

Powermaster®, Lionel ZW®, ZW®

To operate properly, your Heliport requires

12-18 volts (AC). You can supply power

to this accessory in two ways: wiring directly

to your transformer OR wiring to a Lionel

LockOn (available separately) that is

attached to the track. Figure 1 illustrates the

following procedure.

To make the proper connections, the

ends of the wires must be stripped back 1/4”

to 3/8”. Use a pair of wire strippers or a

sharp knife to strip the wires.

Only an adult should perform

this task! Always use care

when stripping wires.

1. Attach one wire to the “U” terminal of

your transformer OR to one terminal on

your Lionel LockOn (available separate-

ly).

LockOn Users! Attach the LockOn to

any section of straight track. Fit the cen-

ter lip of the LockOn onto the edge of the

outside rail and press the LockOn

upward so that the spring contact snaps

onto the center rail. To attach wires to

the LockOn, simply depress the spring

clip and insert the bare end of the wire

into the exposed opening. Release the

clip, and gently tug on the wire to be

sure that you have a good connection.

2. Connect this wire to one of the spring

clips labeled TRANSFORMER CLIPS at

the bottom of the accessory.

To attach this wire, simply depress

the spring clip and insert the bare

end of the wire into the exposed opening.

Release the clip, and gently tug on the wire

to be sure that you have a good connection.

3. Attach another wire to the “A” terminal

on your transformer OR to the other ter-

minal on your Lionel LockOn.

4. Connect this wire to the other spring clip

labeled TRANSFORMER CLIPS at the

bottom of the accessory.

5. To wire the launch switch, attach one

wire to the each of the spring clips

labeled TRIGGER SWITCH at the bottom

of the accessory.

6. Connect each of these wires to the termi-

nals on the separate switch (included

with your accessory).

At this point, you have supplied power to the

accessory and wired the control button.

Wiring your Lionel Heliport for conventional (non-Command) operation

Note!

Caution!

Wiring your Lionel Heliport for conventional (non-Command) operation

(Continued)

Bottom Rear

of Base

Figure 1. Wiring for conventional operation

Launch your helicopter by pressing the launch button that you connected in steps five and

six of the previous section.

Operating your accessory in conventional (non-Command) mode

Your Heliport can be used in the

TrainMaster Command Control environ-

ment. To wire your Lionel Heliport with an

SC-1, follow these steps. Figure 2 illustrates

the following procedure.

1. Attach one wire to the “U” terminal on

your transformer or power supply.

2. Connect this wire to one of the spring

clips under the TRANSFORMER CLIPS

label at the bottom of the accessory.

3. Attach another wire to the “A” terminal

on your transformer or power supply.

4. Connect this wire to the other spring clip

under the TRANSFORMER CLIPS label at

the bottom of the accessory.

5. Attach another wire to the SC-1 unit’s

AUX1, position 1 (or next available posi-

tion) terminal.

6. Connect this wire to one of the spring

clips under the TRIGGER SWITCH label

at the bottom of the Heliport.

7. Attach another wire to the center

(ground) screw on your SC-1 unit.

8. Connect this wire to the other spring clip

under the TRIGGER SWITCH label at the

bottom of the Heliport.

At this point, you have supplied power to

the accessory and wired the control button.

Refer to your SC-1 instructions for addition-

al information.

Wiring your Heliport with an SC-1 Switch and Accessory Controller for

TrainMaster Command Control Operation

Figure 2. Wiring for Command operation with an SC-1

Your Heliport can be used in the

TrainMaster Command Control environ-

ment. To wire your Lionel Heliport with an

SC-2 (part no. 6-22980), follow these steps.

Figure 3 illustrates the following procedure.

1. Attach one wire to the “U” terminal on

your transformer or power supply.

2. Connect this wire to one of the spring

clips under the TRANSFORMER CLIPS

label at the bottom of the accessory.

3. Attach another wire to the “A” terminal

on your transformer or power supply.

4. Connect this wire to the other spring clip

under the TRANSFORMER CLIPS label at

the bottom of the accessory.

5. Attach another wire to the SC-2 unit’s

ACC1, momentary position 1 (or next

available position).

6. Connect this wire to one of the spring

clips under the TRIGGER SWITCH label

at the bottom of the Heliport.

7. Attach another wire to the SC-2 unit’s

COMMON post on your SC-2.

8. Finally, connect this wire to the other

spring clip under the TRIGGER SWITCH

label at the bottom of the Heliport.

At this point, you have supplied power to

the accessory and wired the control button.

Refer to your SC-2 instructions for addition-

al information.

Wiring your Heliport with an SC-2 Switch and Accessory Controller for

TrainMaster Command Control Operation

Figure 3. Wiring for Command operation with an SC-2

Operating this accessory with your CAB-1

Remote Controller is easy! Begin by

assigning an ID# to your Lionel Heliport.

1. Be sure that the Command Base is ON.

2. Power up or plug in the SC-1 or SC-2.

3. Slide the PGM/RUN switch to PGM on

the SC-1 or SC-2. Refer to Figure 4 for

switch locations.

4. On the CAB-1 remote, press the ACC

button.

5. Press 1 on the numeric keypad. This

accessory has the ID# of 1.

6. Press SET on the CAB-1 remote.

7. Slide the PGM/RUN switch back to RUN.

After you have completed these steps to

assign an ID#, simply address your accessory

by pressing the ACC button on the CAB-1

remote, enter the ID# you have set. Press

AUX1 on your CAB-1 remote to launch the

helicopter. Please refer to your SC-1 or SC-2

Switch and Accessory Guide for more

information.

Operating your Heliport with TrainMaster Command Control

PROG/RUN

Figure 4. PROG/RUN switch locations on the SC-1 and SC-2

SC-1 PROG/RUN

SWITCH SC-2 PROG/RUN

SWITCH

After you have completed the wiring of

this accessory, your Lionel Heliport is

clear for landing on your layout!

1. Place the Heliport on a flat, level

section of your layout.

You may want to consider locating the

Heliport in where it will be in easy reach

for preparing the helicopter for launch.

Securing this accessory to your layout is

also your choice; you will find two slot-

ted areas on the base of the Heliport for

this purpose.

2. Next, install the radar dishes and

megaphones.

Attach the two radar dishes to the post

and push the base of the post into the

opening on the roof. Refer to the dia-

gram for assembly and installation

details. Attach the two molded mega-

phones above or below the roof as indi-

cated in Figure 5.

3. Finally, install the black tail sup-

port structure.

Simply push the two legs into the two

openings on the roof.

Installing your Lionel Heliport

Roof Nut

Tail Support

Radar

Megaphone

Figure 5. Installing roof details

The Heliport is wired, positioned, and

assembled. You are clear for takeoff!

Here are your flight instructions.

1. Slide the metal lever all the way

to the right to so that the metal

locking mechanism catches each

of the three “teeth” along the

sides of the platform/dial.

If the metal locking mechanism is

not in position to capture each

tooth, the platform will unwind immediately.

2 Turn the black helicopter plat-

form/dial clockwise approximate-

ly seven to eight clicks.

3 Next, place the helicopter on the

launching platform.

The tail should rest on the black support

structure to the right of the launching

platform. The body of the helicopter

should rest on the launching platform.

The notches or teeth in the center

of the platform and at the bottom

of the helicopter must fit together. Rotate

the helicopter blades while the helicopter is

in position until these notches fit together.

4. Launch your helicopter by press-

ing the launch button or by using

the Cab-1 remote. For informa-

tion about using the CAB-1, refer

to the Command Control sections

above.

If you press the button and the

helicopter does not launch, simply

tap on the roof of the structure to release any

binds that have occurred in the mechanism.

Have a great flight!

The blades of the helicopter

rotate to provide lift. Keep

clear of the accessory when launching the

helicopter.

Launching your helicopter

Note!

Winding Lock

Keyed shafts

must align Switch

Tail placed on

support structure

Note!

Caution!

Figure 6. Preparing the helicopter for launch

Table des matières

Autres manuels Lionel Jouet

Lionel

Lionel Fire Set Manuel utilisateur

Lionel

Lionel ALCo S-2 Manuel utilisateur

Lionel

Lionel Trolley Manuel utilisateur

Lionel

Lionel Pennsylvania ALCo A-A Set Manuel utilisateur

Lionel

Lionel Scout Set Manuel utilisateur

Lionel

Lionel The Polar Express G-gauge Manuel utilisateur

Lionel

Lionel Rectifier electric locomotive Manuel utilisateur

Lionel

Lionel Giraffe Car Manuel utilisateur

Lionel

Lionel Alco PB-1 Manuel utilisateur

Lionel

Lionel RS-11 Manuel utilisateur

Lionel

Lionel Zenith Express Manuel utilisateur

Lionel

Lionel O72 Wye Remote Switch Fastrack Manuel utilisateur

Lionel

Lionel Bay WindowCrew Talk Caboose Manuel utilisateur

Lionel

Lionel Pennsylvania S-2 Manuel utilisateur

Lionel

Lionel Ready-to-Play Series Manuel utilisateur

Lionel

Lionel Little Lines Freight Set Manuel utilisateur

Lionel

Lionel Dash 9 Diesel Locomotive Manuel utilisateur

Lionel

Lionel 101 Manuel utilisateur

Lionel

Lionel LionChief Plus 2-8-2 Mikado Manuel utilisateur

Lionel

Lionel Mervyn's Bring Home the Holidays Manuel utilisateur

Lionel

Lionel NW2 Manuel utilisateur

Lionel

Lionel Railroad Tugboat Manuel utilisateur

Lionel

Lionel 1563W Wabash Freight Set Manuel utilisateur

Lionel

Lionel 238E Torpedo 4-6-2 steam locomotive Manuel utilisateur

Manuels Jouet populaires d'autres marques

marklin

marklin 37321 Manuel utilisateur

Canon

Canon PAPER CRAFT Manuel utilisateur

GREAT PLANES

GREAT PLANES Pitts M-12S Manuel utilisateur

NOCH

NOCH 14261 Manuel utilisateur

Hausler

Hausler 450 SE V2 Manuel utilisateur

Dynaflite

Dynaflite Daydream Manuel utilisateur

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuel

Kenner

Kenner Batman 63651 Manuel utilisateur

LEGO

LEGO 8527 Manuel utilisateur

iKarus

iKarus ECO 8 Manuel utilisateur

Multiplex

Multiplex EasyStar II Mode d’emploi

Walkera

Walkera 38 Mode d’emploi

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuel utilisateur

MD MXION SWD Manuel utilisateur

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuel utilisateur

marklin

marklin 39671 Manuel utilisateur

Meccano

Meccano 15103 Manuel utilisateur

LEGO

LEGO TECHNIC 8735 Manuel utilisateur