Linksys WAP11 v2.2 Manuel utilisateur

LINKSYS

WAP11 V2.2

Version:1.0 Date:2001/12/21

Federal Communications Commission Statement

This device complies with FCC Rules Part 15. Operation is subject to the following two conditions:

Thisdevicemaynotcauseharmfulinterference.

This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy. If this equipment

is not installed and used in accordance with the manufacturer's instructions, it may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by

during the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

followingmeasures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

Consultthe dealer or an experienced radio/TV technician forhelp.

The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance

with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Manufacturer's Disclaimer Statement

The information in this document is subject to change without notice and does not represent a commitment on the

part of the vendor. No warranty or representation, either expressed or implied, is made with respect to the

quality, accuracy or fitness for any particular purpose of this document. Themanufacturer reserves therightto

make changes to the content of this document and/or the products associated with it at any time without obligation

to notify any person or organization of such changes. In no event will the manufacturer be liable for direct,

indirect, special, incidental or consequential damages arising out of the use or inability to use this product or

documentation, even if advised of the possibility of such damages. This document contains materials protected

by copyright. All rights are reserved. No part of this manual may be reproduced or transmitted in any form, by

any means or for any purpose without expressed written consent of its authors. Product names appearing in this

document are mentioned for identification purchases only. Alltrademarks,productnamesorbrandnames

appearing in this document are registered property of their respective owners.

PrintedinTaiwan

Contents

SECTION 1 ABOUT WAP11 V2.2.........................................................................................3

INTRODUCTION........................................................................................................................................................3

1-1 FEATURES...........................................................................................................................................................3

1-2 FIRMWARE FUNCTIONALITY...................................................................................................................3

1-3 APPLICATIONS.................................................................................................................................................3

1-4 PRODUCT KIT..................................................................................................................................................4

SECTION 2 HARDWARE INSTALLATION...........................................................5

2-1 EQUIPMENT REQUIREMENT....................................................................................................................5

2-2 HARDWARE INSTALLATION.................................................................................................................5

SECTION 3 INSTALLING & CONFIGURING WAP11 V2.2..............6

3-1 INSTALLING AND CONFIGURING WAP11 V2.2.........................................................................6

3-1-1 Setup ..................................................................................................................................................................6

3-1-2 Advanced Setup...............................................................................................................................................11

APPENDIX ASPECIFICATIONS......................................................................................13

APPENDIX BGLOSSARY..........................................................................................................14

Section 1 About WAP11 V2.2

Introduction

The 22 Mbps WAP11 V2.2 is a long-range, high performance and high powered LAN product, which

provides WAP11 V2.2 services to a 2,4 GHz RF network and bridges to an Ethernet backbone. The design of

this product is based on Taxes Instrument’s ACX100 chip, a highly integrated ASIC designed to combine

legacy LANs with wireless LANs. ACX100 performs all the necessary inter-networking and bridging

functions. It receives data from both networks, stores them locally for further processing, installs and

maintains connections and transmits the packets to the appropriate destination. Furthermore, ACX100

interfaces three more modules, the Ethernet PHY, the wireless PHY and the RAM modules, for allowing

compact system implementation and flexibility for supporting almost all the possible physical interfaces.

1-1 Features

–Supports 22 Mbps rates with automatic fallback to 11, 5.5, 2 and 1 Mbps

–For the security aspects, current firmware supports 64/128/256 Bit WEP encryption/decryption and

Password Setting function.

–Ethernet MAC supports MII interface and 10/100Mbit Half/Full Duplex speeds

–Hardware modules for Packet Filtering and statistics gathering

–Dynamic SRAM, Flash interface for data buffering and program storage, supporting up to 16 MB of

memory

–Integrated 2 x 6K x 32 bit internal SRAM modules for fast 32-bit program execution and temporary

storage of data

–JTAG Boundary Scan (IEEE 1149.1) test access port for board-level production test

–SupportsDHCP Client Function, Building to Building Bridge Function.

–SupportsMAC Filtering function to avoid the WAP11 V2.2 loading thru connection with the

unauthorized MAC addresses.

–SupportsStation information to check the association status with other stations.

–SupportsStatistic data for the connection.

1-3 Applications

The Wireless LAN product provides a fast, reliable, cost-effective solution, allowing clients to wirelessly

access the network in applications such as following:

1. Remote access to corporate network information

E-mail, file transfer and terminal emulation

2. Difficult-to-wireenvironments

Historical orlistedbuildings, asbestos installations, and open area where wiring is difficult to employ

3. Frequently changing environments

Retailers, manufacturers and banks who frequently rearrange the workplace and change location

4. Temporary LANs for special projects or peak time

Trade shows, exhibitions and construction sites needing temporary setup for a short time period. Retailers,

airlinesand shipping companies needing additional workstations for a peak period. Auditors requiring

temporary workgroups at customer sites.

5. Access to database for mobile workers

Doctors, nurses, retailers and white-collar workers needing access to database while being mobile in the

hospital, retail store or office campus.

6. SOHO (Small Office and Home Office) users

SOHO users needing easy and quick installation of a small computer network.

1-4 Product Kit

uWAP11 V2.2… ………………………………………………………….x 1

uEthernet Cable (UTP Straight cable)………………………………x 2

uA/C Power Adapter………………………………………….………x 1

uQuick Installation Guide……………………………………………x 2

uUser’s Manual…….………………………………………….………x 1

If any of the listed items are not included orfound damaged, please contact your local dealer.

Section 2 Hardware Installation

2-1 Equipment Requirement

Installation requirement:

1.An A/C power outlet (100~240V,50~60Hz) which supplythe power for the WAP11 V2.2

2.A 10 Base-T/100 Base-TX (UTP) Ethernet cable drop (RJ-45 connector)

2-2 Hardware Installation

Please follow these procedures while setting up the hardware:

1.Site Selection

Choose a proper location for your WAP11 v2.2.

In general, the best location to place your WAP11 v2.2 is the center of your wireless coverage, with line of

sight to all your mobile stations.

2.Adjust the direction ofthe Antenna

Adjust the direction of the antenna placementto improve the WAP11 v2.2’s performance. Try to place the

antenna in the position which can best cover its BSS. Normally, the higher you place the antenna, the better

the performance will be.The character of diversity enhances the receiving sensitivity.

3.Connect the Ethernet Cable

Can be connected to the 10 Base-T/100 Base-TX Ethernet network. Connect your UTP Ethernet cable to

the RJ-45 connector of the WAP11 v2.2 and connect theother side of UTP Ethernet cable to a hub.

4.Connect the Power Cable

Connect the power adapter cable to the DC5V Power Socket of the WAP11 v2.2. ONLY use the power

adapter supplied with the WAP11 v2.2. Otherwise, the product may be damaged.

Section 3 Configuring WAP11 V2.2

3-1 Installing and Configuring WAP11 V2.2

The WAP11 V2.2 can be configured using the web browser from Windows®98/2000/ME/XP. You need

to plug the direct network cable to the LAN port then start your web browser and type http://192.168.1.1 in

the address box. This number is the default IP address of your WAP11 V2.2.

A user name and password prompt will appear. Type in “admin” as user name and “admin”as the

password. Click “Ok”.

Setup

The setup page will be the main page.

On the Setup page, you are able to find:

ØThe current firmware version and dates.

ØLAN IP Address

ØWirelesssetting

You may “Enable”or “Disable”wireless services, if you choose to enable it, please setup your

“ESSID”and “Channel”numbers. You may alsodisable the WEP or change it to “Mandatory”by

clicking “WEP Key Setting”. By clicking “WEP Key Setting”, it will prompt you a message, click

“ok”to continue.

By clicking “OK”, another window will open up and you can start setting the WEP Key in the window.

You may select 64bit, 128bit or 256bit encryption.

WEP Encryption key can be generated in one of two ways:

1. You can create an encryption key by using a Passphrase. To generate the encryption key using a

passphrase, enter a text string in thePassphrase box and press the Generte button. The passphrase

can be any text string with a maximum of 31 alphanumeric characters.

2. You may enter the encryption key manually.

Click the “Apply”button to complete the encryption setup.

Password

You may reset the password in this page. Click “Apply”when complete.

Status

You can view the current status and settings. You may also perform the backup and restore your personal

settings.

When you click on “backup”it will prompt you a location to save the“config.bin”file.

When you try to restore the settings you have saved, click “Browse”to locate the file and perform the

restore procedure.

Log

You may enable or disable the logging and send the log to different location within your network.

Autres manuels pour WAP11 v2.2

Table des matières

Autres manuels Linksys Point d'accès sans fil

Linksys

Linksys EtherFast Instant Broadband BEFW11S4 Instructions d'utilisation d'origine

Linksys

Linksys Instant Broadband Series Manuel utilisateur

Linksys

Linksys WAP2000 Manuel d'utilisation

Linksys

Linksys EtherFast Instant Broadband BEFW11S4 Manuel utilisateur

Linksys

Linksys WAP54GX Manuel utilisateur

Linksys

Linksys WAP54G - Wireless-G Access Point Manuel utilisateur

Linksys

Linksys WAP54A - Instant Wireless - Access Point Manuel utilisateur

Linksys

Linksys WAP11 - Instant Wireless Network Access... Manuel utilisateur

Linksys

Linksys WAP54GP - Wireless-G Access Point Manuel utilisateur

Linksys

Linksys Instant Wireless Series WAP54G Manuel utilisateur

Linksys

Linksys WAP4400N Manuel d'utilisation

Linksys

Linksys WAP54A - Instant Wireless - Access Point Manuel utilisateur

Linksys

Linksys WAP54G v2 Manuel utilisateur

Linksys

Linksys WAP54GPE - Wireless-G Exterior Access Point Manuel utilisateur

Linksys

Linksys WAP54G - Wireless-G Access Point Manuel d'utilisation

Linksys

Linksys WAP2000 Manuel utilisateur

Linksys

Linksys WAP54GP - Wireless-G Access Point Manuel utilisateur

Linksys

Linksys WPG54G Manuel utilisateur

Linksys

Linksys WAP4400N Manuel utilisateur

Linksys

Linksys WAP51AB - Instant Wireless - Access Point Manuel utilisateur

Linksys

Linksys WAP200E Manuel utilisateur

Linksys

Linksys WAP54G - Wireless-G Access Point Manuel utilisateur

Linksys

Linksys WAP51AB - Instant Wireless - Access Point Instructions d'utilisation d'origine

Linksys

Linksys WAP55AG - Wireless A+G Access Point Instructions d'utilisation d'origine

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur