LiniLED PCB Photon Series Manuel utilisateur

LED strip manual

liniLED® PCB Photon

BEND RADIUS

20 mm

FRoHS

V D

IP00

CRI

MAC

ADAM

S D C M

General

Handling

Installation

Operation and use

Cleaning and maintenance

Environment and waste

Warning

Area advice

Product dimensions

Product information

Product specications

Cable selection

Product care and handling

Cutting instructions

Soldering

Connect IP00

Power supply

Symbols

LED strip PCB Photon

4LED strip manual | liniLED® PCB Photon

Read the instructions and safety precautions before installation, usage and storage of the products to secure safety of the user and reliability of the product.

- Hand over the instructions to the end user and those responsible for installation and usage.

- Triolight B.V. cannot be held responsible for improper handling, product installation, usage or storage.

Handling

- Handle with care.

- The product may not be modied or converted otherwise than prescribed.

- Products are transported in proper packaging. Products should remain packed until installation.

- Take ESD (Electrostatic Discharge) protection measures when handling liniLED® products.

- The products and their components may not be exposed to mechanical, static loads and other tension/compression other than from the product itself.

Installation

- Attention: The power has to be switched o the main power supply or the connection before installation. Not doing so may damage the product.

- Use a suitable LED power supply/driver: 24 V DC constant voltage. Do not drive the product on other voltages than described in their datasheet/products

specications.

- Installation has to be done by a certied professional with knowledge of electrical circuits or a specialised maintenance person known with valid directives.

- General and local construction-, safety- and installation regulations should be respected.

- Use only supplied parts, accessories and required tools as prescribed in the installation manual to guarantee a safe installation and use of the product.

- Products may solely be installed in the areas according to their prescribed IP-rating, IK-rating, temperature range and chemical resistances.

- The LED strip should be installed on an adequate cooling body for proper heat dissipation to ensure smooth operation and long lifetime.

- Do not fasten anything on the product, same applies for hanging.

- Do not install the product in the following cases:

- Damage is visible on the product or its cables.

- The inside of the product is moistened or dirty.

- The product or its cables have been modied. It could lead to an electrical shock or a short circuit may occur.

- Children may not play unsupervised with electrical products as they cannot judge the dangers in dealing with electrical circuits correctly.

- Use proper mounting surfaces when installing in environments with large variations in temperature and operating lengths more than 2m. This should

absorb the stress of any mismatch in expansion.

Operation and use

Solely use the product when its working correctly. If not, switch the power o immediately and advise an electrical specialist in the following cases:

- Damage is visible on the product and/or the product does not function.

- The product is overheating and/or smoke or steam rises from the product.

- Crackling sounds are noticeable.

- Repairs on the installation may only be performed by qualied electricians. Product repairs may solely be done by Triolight B.V.

Cleaning and maintenance

- Attention: Disconnect the power before maintenance and cleaning.

- Dust and dirt accumulated over time should be removed from the light emitting surface to assure optimal functioning of the product.

- Paints, solvents and corrosive cleaning chemicals may not contact and thus aect the product.

Environment and waste

- Exterior decorative lighting should only be used after sunset.

- This product may not be treated as household waste. Dispose of the material through the waste recycling of electrical and electronic equipment.

Warranty

This product comes with a 2 year warranty. Warranty void if:

- The installation guide has not been consulted (installation mistake).

- The installation is not done by a certied installer.

- Local rules and guidelines are not respected.

- The invoice cannot be shown and/or has been altered.

- Damage is caused by negligence, abnormal use or improper handling, use, maintenance and/or cleaning of the product.

Technical notes

5LED strip manual | liniLED® PCB Photon

Area advice

Indoor environment (IP00)

Solder

Indoor environment (IP00) | liniLED® PCB Connector set

Product code: 11808

Depending on the area where the liniLED® LED strip is installed we oer a range of solutions to cope with external factors. The product portfolio

for the liniLED® PCB LED strip only includes a range of IP00 connectors.

LED strip top view

LED strip front view

Product dimensions

1/2.2

100

6LED strip manual | liniLED® PCB Photon

Product information

Product specications

Colour

2000K

2400K

2700K

3000K

4000K

6500K

Colour

2000K

2400K

2700K

3000K

4000K

6500K

Colour

2000K

2400K

2700K

3000K

4000K

6500K

Colour

2000K

2400K

2700K

3000K

V DC

Temp ˚C

-30...55

Temp ˚C

-30...55

Temp ˚C

-30...55

Temp ˚C

-30...55

LED/m

W/m

10.6

8.9

8.1

W/m

17.9

13.6

W/m

28.9

23.7

21.8

W/m

28.9

Max. Length

9 m

Max. Length

4.5 m

Max. Length

3 m

Max. Length

3 m

lm/m

1002

1170

1208

1230

1221

1223

lm/m

1536

1709

1742

1798

1831

1813

lm/m

2292

2545

2631

2785

2663

2614

lm/m

3300

3401

3415

3404

B50/L70

> 50.000 h

B50/L70

> 50.000 h

B50/L70

> 50.000 h

B50/L70

> 50.000 h

The liniLED® LED strip PCB Photon (IP00) is a high quality, exible LED strip with an outstanding eciency. Thanks to the small dimensions, the

PCB LED strip is ideal to use in small spaces (indoor use only!). With 3M double sided tape on the back, the PCB LED strip is easy to mount. The

liniLED® LED strip PCB Photon serie is available in various white colours and lumen (1200-4000).

* Connect the PCB LED strips with the PCB Connector Set and the PCB Inline Connector. See datasheet for more information.

Photon 1200Photon 2000Photon 3000Photon 4000

7LED strip manual | liniLED® PCB Photon

The liniLED® LED strips need a minimum voltage at the beginning of the LED strip to function according to the specications. The table below gives an indication

of the maximum cable length based on the cable thickness and power supply voltage. The connection between the cable and LED strip is with a

liniLED® Connector.

In case the required length is larger than the length mentioned in this table, the supply voltage is dierent or if a detailed wire plan with

branches is planned, please contact your distributor for a detailed cable calculation.

1 m

2 m

5 m

9 m

1 m

2 m

5 m

9 m

1 m

2 m

5 m

9 m

1 m

2 m

5 m

9 m

1 m

2 m

5 m

9 m

27.95 m

13.33 m

4.56 m

1.96 m

42.04 m

20.05 m

6.86 m

2.95 m

55.90 m

26.66 m

9.12 m

3.92 m

84.09 m

40.11 m

13.72 m

5.91 m

139.96 m

66.76 m

22.84 m

9.83 m

33.53 m

16.12 m

5.68 m

2.58 m

50.45 m

24.25 m

8.54 m

3.88 m

67.07 m

32.25 m

11.36 m

5.17 m

100.90 m

48.51 m

17.08 m

7.77 m

167.92 m

80.74 m

28.44 m

12.94 m

36.97 m

17.84 m

6.36 m

2.96 m

55.62 m

26.84 m

9.57 m

4.46 m

73.95 m

35.69 m

12.73 m

5.93 m

111.24 m

53.69 m

19.15 m

8.92 m

185.14 m

89.35 m

31.88 m

14.85 m

54.85 m

26.78 m

9.94 m

4.95 m

82.51 m

40.29 m

14.95 m

7.45 m

109.70 m

53.56 m

19.88 m

9.90 m

165.02 m

80.58 m

29.91 m

14.90 m

274.64 m

134.10 m

49.78 m

24.80 m

65.57 m

32.14 m

12.08 m

6.14 m

98.64 m

48.35 m

18.18 m

9.24 m

131.14 m

64.29 m

24.17 m

12.28 m

197.28 m

96.71 m

36.36 m

18.48 m

328.33 m

160.95 m

60.52 m

30.76 m

72.17 m

35.44 m

13.40 m

6.87 m

108.57 m

53.32 m

20.16 m

10.34 m

144.35 m

70.89 m

26.81 m

13.75 m

217.15 m

106.64 m

40.33 m

20.69 m

361.40 m

177.48 m

67.13 m

34.44 m

liniLED® cable (2 x 0.50 mm)

0.035 Ω/m

liniLED® cable (2 x 0.75 mm)

0.023 Ω/m

liniLED® cable (2 x 1.00 mm)

0.018 Ω/m

liniLED® cable (2 x 1.50 mm)

0.012 Ω/m

liniLED® cable (2 x 2.50 mm)

0.007 Ω/m

Cable X information LED strip Max. cable length 2000, 2400K Max. cable length 2700, 3000K Max. cable length 4000, 6500K

@ 24 V DC @ 24 V DC @ 24 V DC@ 25V DC @ 25V DC @ 25V DC

Cable Selection Photon 1200

Cable Selection Photon 2000

The liniLED® LED strips need a minimum voltage at the beginning of the LED strip to function according to the specications. The table below gives an indication

of the maximum cable length based on the cable thickness and power supply voltage. The connection between the cable and LED strip is with a

liniLED® Connector.

In case the required length is larger than the length mentioned in this table, the supply voltage is dierent or if a detailed wire plan with

branches is planned, please contact your distributor for a detailed cable calculation.

1 m

2 m

3 m

4.5 m

1 m

2 m

3 m

4.5 m

1 m

2 m

3 m

4.5 m

1 m

2 m

3 m

4.5 m

1 m

2 m

3 m

4.5 m

16.02 m

7.37 m

4.48 m

2.56 m

24.11 m

11.09 m

6.74 m

3.85 m

32.05 m

14.74 m

8.97 m

5.12 m

48.22 m

22.18 m

13.49 m

7.71 m

80.26 m

36.91 m

22.46 m

12.83 m

19.37 m

9.04 m

5.60 m

3.30 m

29.14 m

13.60 m

8.42 m

4.97 m

38.75 m

18.09 m

11.20 m

6.61 m

58.29 m

27.21 m

16.85 m

9.95 m

97.02 m

45.29 m

28.05 m

16.55 m

21.50 m

10.10 m

6.31 m

3.77 m

32.34 m

15.20 m

9.49 m

5.68 m

43.00 m

20.21 m

12.62 m

7.55 m

64.69 m

30.41 m

18.98 m

11.37 m

107.67 m

50.62 m

31.60 m

18.92 m

31.95 m

15.33 m

9.79 m

6.10 m

48.07 m

23.07 m

14.73 m

9.18 m

63.91 m

30.67 m

19.59 m

12.20 m

96.14 m

46.14 m

29.47 m

18.36 m

160.01 m

76.79 m

49.05 m

30.55 m

38.38 m

18.55 m

11.93 m

7.53 m

57.74 m

27.90 m

17.95 m

11.32 m

76.77 m

37.10 m

23.87 m

15.06 m

115.48 m

55.81 m

35.91 m

22.65 m

192.19 m

92.88 m

59.78 m

37.71 m

42.46 m

20.59 m

13.30 m

8.43 m

63.88 m

30.97 m

20.00 m

12.69 m

84.93 m

41.18 m

26.60 m

16.87 m

127.76 m

61.95 m

40.01 m

25.38 m

212.64 m

103.10 m

66.59 m

42.25 m

liniLED® cable (2 x 0.50 mm)

0.035 Ω/m

liniLED® cable (2 x 0.75 mm)

0.023 Ω/m

liniLED® cable (2 x 1.00 mm)

0.018 Ω/m

liniLED® cable (2 x 1.50 mm)

0.012 Ω/m

liniLED® cable (2 x 2.50 mm)

0.007 Ω/m

Cable X information LED strip Max. cable length 2000, 2400K Max. cable length 2700, 3000K Max. cable length 4000, 6500K

@ 24 V DC @ 24 V DC @ 24 V DC@ 25V DC @ 25V DC @ 25V DC

8LED strip manual | liniLED® PCB Photon

The liniLED® LED strips need a minimum voltage at the beginning of the LED strip to function according to the specications. The table below gives an indication

of the maximum cable length based on the cable thickness and power supply voltage. The connection between the cable and LED strip is with

a liniLED® Connector.

In case the required length is larger than the length mentioned in this table, the supply voltage is dierent or if a detailed wire plan with branches is planned,

please contact your distributor for a detailed cable calculation.

1 m

2 m

3 m

1 m

2 m

3 m

1 m

2 m

3 m

1 m

2 m

3 m

1 m

2 m

3 m

9.43 m

4.07 m

2.29 m

14.19 m

6.13 m

3.44 m

18.87 m

8.15 m

4.58 m

28.39 m

12.26 m

6.89 m

47.26 m

20.41 m

11.46 m

11.79 m

5.25 m

3.07 m

17.73 m

7.90 m

4.62 m

23.58 m

10.50 m

6.14 m

35.47 m

15.80 m

9.25 m

59.04 m

26.30 m

15.39 m

12.93 m

5.82 m

3.45 m

19.45 m

8.76 m

5.19 m

25.86 m

11.64 m

6.90 m

38.90 m

17.52 m

10.39 m

64.75 m

29.16 m

17.29 m

19.30 m

9.01 m

5.57 m

29.04 m

13.55 m

8.39 m

38.61 m

18.02 m

11.15 m

58.08 m

27.10 m

16.78 m

96.66 m

45.11 m

27.93 m

23.82 m

11.26 m

7.08 m

35.83 m

16.95 m

10.65 m

47.64 m

22.53 m

14.16 m

71.67 m

33.90 m

21.31 m

119.28 m

56.42 m

35.47 m

26.01 m

12.36 m

7.81 m

39.12 m

18.59 m

11.75 m

52.02 m

24.72 m

15.62 m

78.25 m

37.19 m

23.50 m

130.24 m

61.90 m

39.12 m

liniLED® cable (2 x 0.50 mm)

0.035 Ω/m

liniLED® cable (2 x 0.75 mm)

0.023 Ω/m

liniLED® cable (2 x 1.00 mm)

0.018 Ω/m

liniLED® cable (2 x 1.50 mm)

0.012 Ω/m

liniLED® cable (2 x 2.50 mm)

0.007 Ω/m

Cable X information LED strip Max. cable length 2000, 2400K Max. cable length 2700, 3000K Max. cable length 4000, 6500K

@ 24 V DC @ 24 V DC @ 24 V DC@ 25V DC @ 25V DC @ 25V DC

Cable selection Photon 3000

Cable selection Photon 4000

The liniLED® LED strips need a minimum voltage at the beginning of the LED strip to function according to the specications. The table below gives an indication

of the maximum cable length based on the cable thickness and power supply voltage. The connection between the cable and LED strip is with

a liniLED® Connector.

In case the required length is larger than the length mentioned in this table, the supply voltage is dierent or if a detailed wire plan with branches is planned,

please contact your distributor for a detailed cable calculation.

1 m

2 m

3 m

1 m

2 m

3 m

1 m

2 m

3 m

1 m

2 m

3 m

1 m

2 m

3 m

9.43 m

4.07 m

2.29 m

14.19 m

6.13 m

3.44 m

18.87 m

8.15 m

4.58 m

28.39 m

12.26 m

6.89 m

47.26 m

20.41 m

11.46 m

19.30 m

9.01 m

5.57 m

29.04 m

13.55 m

8.39 m

38.61 m

18.02 m

11.15 m

58.08 m

27.10 m

16.78 m

96.66 m

45.11 m

27.93 m

liniLED® cable (2 x 0.50 mm)

0.035 Ω/m

liniLED® cable (2 x 0.75 mm)

0.023 Ω/m

liniLED® cable (2 x 1.00 mm)

0.018 Ω/m

liniLED® cable (2 x 1.50 mm)

0.012 Ω/m

liniLED® cable (2 x 2.50 mm)

0.007 Ω/m

Cable X information LED strip Max. cable length 2700 t/m 6500K

@ 24 V DC @ 25V DC

9LED strip manual | liniLED® PCB Photon

Do not bend the LED strip sidewards. Do not twist the LED strip.

The LED strip has to be unreeled on a horizontal surface at the time of installation. Do not unreel the spool of LED strip before installation.

Product care and handling

20 mm

Do not compress or stretch the LED strip.

Maximum bending radius is 20 mm. Solely bend up- or downwards.

10 LED strip manual | liniLED® PCB Photon

Cutting instructions

Dispose of the unnecessary material through waste recycling of

electrical and electronic equipment.

Top view | Only cut on the dotted lines to prevent damaging the LED

strip.

Turn o the power before cutting the LED strip.

Work in an ESD protected environment. Make use of an anti-static

strap.

Top view | Make sure the cut is vertical as illustraded in the image

above.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels liniLED Multiprise

liniLED

liniLED Diffuse G4 Manuel utilisateur

Manuels Multiprise populaires d'autres marques

Conrad Electronic

Conrad Electronic Renkforce 1296313 Manuel utilisateur

Hama

Hama 00223192 Manuel utilisateur

Iiglo

Iiglo IIERGOPS014 Manuel utilisateur

Leonics

Leonics TPS SERIES Manuel utilisateur

Renkforce

Renkforce 1210387 Manuel utilisateur

Xiaomi

Xiaomi KingMi Manuel utilisateur

Bauhn

Bauhn ASPP8-0422-W Manuel utilisateur

Sygonix

Sygonix 2541578 Manuel utilisateur

Maxxima

Maxxima MEP-8DW Manuel

Bauhn

Bauhn ASPPD6-0121 Manuel utilisateur

CyberPower

CyberPower HT705GR Manuel utilisateur

TUYA

TUYA 315946 Manuel utilisateur

LEGRAND

LEGRAND 329 87 Manuel utilisateur

Hama

Hama 223181 Manuel utilisateur

TrickleStar

TrickleStar 188LV-US-7XX Manuel utilisateur

Rennsteig

Rennsteig RAUCUT I Manuel utilisateur

Hama

Hama P2223761 Manuel utilisateur

ZooZ

ZooZ ZEN20 VER. 2.0 Manuel utilisateur

liniLED PCB Photon Series Manuel utilisateur

Manuels Multiprise populaires d'autres marques