Linear Technology LT8570 Guide de configuration rapide
1
dc2297afb
DEMO MANUAL DC2297A
DESCRIPTION
LT8570, LT8570-1
Boost/SEPIC/Inverting Regulator
Demonstration circuits 2297A-A and 2297A-B feature the
LT
®
8570 and LT8570-1 in a boost configuration. These
demo circuits demonstrate small size and low component
count. Both converters are designed to convert a 5V to
10V source to 12V. Refer to Figures 3 and 4 for maximum
load current at different input voltage levels.
Both converters use only one feedback resistor to set the
output voltage.
The LT8570 can operate with inputs as high as 40V but
in these demo circuits, the input is limited by the voltage
rating of the input capacitors, and the magnitude of the
output voltage.
PERFORMANCE SUMMARY
The LT8570 and LT8570-1 include many other features
suchassynchronizationtoexternalclock,userconfigurable
undervoltage lockout, soft-start, frequency foldback, and
other features that are easily configured as Boost, SEPIC
or Inverting Converters.
The data sheet gives a complete description of the device,
operationandapplicationinformation.Thedatasheetmust
bereadinconjunctionwiththisdemomanualforDC2297A.
Design files for this circuit board are available at
http://www.linear.com/demo/DC2297A
L, LT, LTC, LTM, µModule, Linear Technology and the Linear logo are registered trademarks of
Linear Technology Corporation. All other trademarks are the property of their respective owners.
Specifications are at TA= 25°C
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
DC2297A-A
VIN Input Supply Range 5 10 V
VOUT Output Voltage VIN = 5V, ILOAD = 125mA 11.64 12 12.36 V
RIPPLE VIN = 5V, ILOAD = 125mA 25 mV
EFFICIENCY VIN = 5V, ILOAD = 125mA 86 %
SWITCHING FREQUENCY 1.5 MHz
DC2297A-B
VIN Input Supply Range 5 10 V
VOUT Output Voltage VIN = 5V, ILOAD = 60mA 11.64 12 12.36 V
RIPPLE VIN = 5V, ILOAD = 60mA 5 mV
EFFICIENCY VIN = 5V, ILOAD = 60mA 86 %
SWITCHING FREQUENCY 1.5 MHz
2
dc2297afb
DEMO MANUAL DC2297A
QUICK START PROCEDURE
Demo circuit 2297A is easy to set up to evaluate the per-
formance of the LT8570 and LT8570-1. Refer to Figure 1
for proper measurement equipment setup and follow the
procedure below:
NOTE: When measuring the input or output voltage ripple,
care must be taken to avoid a long ground lead on the
oscilloscope probe. Measure the input or output voltage
ripple by touching the probe tip directly across the VIN or
VOUT and GND terminals. See Figure 2 for proper scope
probe technique.
1. With power off, connect the input power supply to VIN
and GND.
2. Turn on the power at the input.
NOTE: Make sure that the input voltage does not
exceed 10V.
3. Check for the proper output voltage.
NOTE: If there is no output, temporarily disconnect the
load to make sure that the load is not set too high.
4. Oncethe proper output voltages are established, adjust
the load within the operating range and observe the
output voltage regulation, ripple voltage, efficiency and
other parameters.
Figure 1. Proper Measurement Equipment Setup
–
+
–
+
+–
+
–
LOAD
–
+
–
+
POWER
SUPPLY VIN VOUT
IOUT
IIN
GND
VIN
Figure 2. Measuring Input or Output Ripple
3
dc2297afb
DEMO MANUAL DC2297A
QUICK START PROCEDURE
INPUT (V)
LOAD (mA)
450
50
400
300
200
100
350
250
150
075 9
DC2297A F03
1064 83
Figure 3. DC2297A-A Max Load Current vs Input Voltage
INPUT (V)
LOAD (mA)
240
80
60
40
20
220
180
140
100
200
160
120
075 9
DC2297A F04
1064 83
Figure 4. DC2297A-B Max Load Current vs Input Voltage
INPUT (V)
EFFICIENCY (%)
90
85
75
65
55
80
70
60
50 8040 120
DC2297A F05
1406020 1000
Figure 5. DC2297A-A Efficiency at 5VIN
INPUT (V)
EFFICIENCY (%)
90
85
75
65
55
80
70
60
50 3010 50
DC2297A F06
6020 400
Figure 6. DC2297A-B Efficiency at 5VIN
4
dc2297afb
DEMO MANUAL DC2297A
PARTS LIST
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER
DC2297A-A
Required Circuit Components for Boost Regulator
1 1 C1 CAP., CER., 4.7µF, X7R, 16V, 10%, 0805 MURATA, GRM21BR71C475KA73L
2 1 C2 CAP., CER., 0.1µF, X7R, 16V, 10%, 0402 MURATA, GRM155R71C104KA88D
3 1 C3 CAP., CER., 2.2nF, X7R, 16V, 10%, 0402 AVX, 0402YC222KAT2A
4 1 C4 CAP., CER., 47pF, C0G, 25V, 5%, 0402 AVX, 04023A470JAT2A
5 1 C6 CAP., CER., 4.7µF, X7R, 16V, 10%, 0805 MURATA, GRM21BR71C475KA73L
6 1 D1 DIODE, SCHOTTKY, 30V, 1A, DI123 DIODES INC., DFLS130-7
7 1 L1 IND., 33µH WÜRTH ELEKTRONIK, 744 042 330
8 1 R2 RES., 11.3k, 1/8W, 1%, 0805 VISHAY, CRCW080511K3FKEA
9 1 R3 RES., 10k, 1/8W, 1%, 0805 VISHAY, CRCW080510K0FKEA
10 1 R5 RES., 56.2k, 1/10W, 1%, 0603 VISHAY, CRCW060356K2FKEA
11 1 R6 RES., 6.04k, 1/10W, 1%, 0603 NIC, NRC06F6041TRF
12 1 R7 RES., 130k, 1/10W, 1%, 0603 VISHAY, CRCW0603130KFKEA
13 1 U1 I.C., LT8570EDD, 8DFN LINEAR TECH., LT8570EDD#PBF
Additional Demo Board Circuit Components
1 1 C5 CAP., CER., 0.1µF, X7R, 16V, 10%, 0603 TDK, C1608X7R1C104K
2 1 R4 RES., 100k, 1/8W, 1%, 0805 VISHAY, CRCW0805100KFKEA
Hardware: For Demo Board Only
1 6 E1–E6 TEST POINT, TURRET, 0.094" MTG HOLE MILL-MAX, 2501-2-00-80-00-00-07-0
DC2297A-B
Required Circuit Components for Boost Regulator
1 1 C1 CAP., CER., 4.7µF, X7R, 16V, 10%, 0805 MURATA, GRM21BR71C475KA73L
2 1 C2 CAP., CER., 0.1µF, X7R, 16V, 10%, 0402 MURATA, GRM155R71C104KA88D
3 1 C3 CAP., CER., 2.2nF, X7R, 16V, 10%, 0402 AVX, 0402YC222KAT2A
4 1 C4 CAP., CER., 47pF, C0G, 25V, 5%, 0402 AVX, 04023A470JAT2A
5 1 C6 CAP., CER., 2.2µF, X7R, 16V, 10%, 0805 MURATA, GRM21BR71C225KA12L
6 1 D1 DIODE, SCHOTTKY, 30V, 1A, DI123 DIODES INC., DFLS130-7
7 1 L1 IND., 68µH U ELEKTRONIK, 744 042 680
8 1 R2 RES., 11.3k, 1/8W, 1%, 0805 VISHAY, CRCW080511K3FKEA
9 1 R3 RES., 10k, 1/8W, 1%, 0805 VISHAY, CRCW080510K0FKEA
10 1 R5 RES., 56.2k, 1/10W, 1%, 0603 VISHAY, CRCW060356K2FKEA
11 1 R6 RES., 6.04k, 1/10W, 1%, 0603 NIC, NRC06F6041TRF
12 1 R7 RES., 130k, 1/10W, 1%, 0603 VISHAY, CRCW0603130KFKEA
13 1 U1 I.C., LT8570EDD-1, 8DFN LINEAR TECH., LT8570EDD-1#PBF
Additional Demo Board Circuit Components
1 1 C5 CAP., CER., 0.1µF, X7R, 16V, 10%, 0603 TDK, C1608X7R1C104K
2 1 R4 RES., 100k, 1/8W, 1%, 0805 VISHAY, CRCW0805100KFKEA
Hardware: For Demo Board Only
1 6 E–E6 TEST POINT, TURRET, 0.094" MTG HOLE MILL-MAX, 2501-2-00-80-00-00-07-0
5
dc2297afb
DEMO MANUAL DC2297A
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-
tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
SCHEMATIC DIAGRAM
C6*
16V
0805
C5
0.1µF
16V
0603
VOUT*
L1*
D1
DFLS130
VIN
5V TO 10V
VIN SW
3 4
R6
6.19k
0603
R3
10k
0805
R2
11.3k
0805
R7
130k
0603
R5
56.2k
0603
R4
100k
0805
SHDN SHDN
GND
GND
E1
E2
E3
E6
E4
E5 GND
FB
VC
15
2
SYNC
SYNC SYNC
RTSS
98 67
C3
2.2nF
C4
47pF
C2
0.1µF
C1
4.7µF
16V
0805
ASSEMBLY TYPE U1 C6 L1 VOUT
DC2297A-A LT8570EDD 4.7µF 33µF 12V/125mA
DC2297A-B LT8570-1EDD 2.2µF 66µH 12V/60mA
* VERSION TABLE
U1*
SHDN
6
dc2297afb
DEMO MANUAL DC2297A
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ●FAX: (408) 434-0507 ●www.linear.com
LINEAR TECHNOLOGY CORPORATION 2015
LT 0317 REV B • PRINTED IN USA
DEMONSTRATION BOARD IMPORTANT NOTICE
Linear Technology Corporation (LT C) provides the enclosed product(s) under the following AS IS conditions:
Thisdemonstrationboard(DEMOBOARD)kitbeingsoldorprovidedbyLinearTechnologyisintendedforuseforENGINEERING DEVELOPMENT
OR EVALUATION PURPOSES ONLY and is not provided by LTC for commercial use. As such, the DEMO BOARD herein may not be complete
in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety
measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union
directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations.
If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 30 days from the date
of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS
FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR
ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LTC from all claims
arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all
appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or
agency certified (FCC, UL, CE, etc.).
No License is granted under any patent right or other intellectual property whatsoever. LT C assumes no liability for applications assistance,
customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind.
LTC currently services a variety of customers for products around the world, and therefore this transaction is not exclusive.
Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and
observe good laboratory practice standards. Common sense is encouraged.
This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LTC applica-
tion engineer.
Mailing Address:
Linear Technology
1630 McCarthy Blvd.
Milpitas, CA 95035
Copyright © 2004, Linear Technology Corporation
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Linear Technology Contrôleurs
Linear Technology
Linear Technology Analog Devices LT8708 Manuel utilisateur
Linear Technology
Linear Technology DC1992A Guide de configuration rapide
Linear Technology
Linear Technology DC1488A Series Manuel utilisateur
Linear Technology
Linear Technology LT3759 Guide de configuration rapide
Linear Technology
Linear Technology DC1817B Guide de configuration rapide
Linear Technology
Linear Technology LTM4636 Manuel utilisateur
Linear Technology
Linear Technology DC1936A Guide de configuration rapide
Linear Technology
Linear Technology LTC4365 Guide de configuration rapide
Linear Technology
Linear Technology DC1596A Guide de configuration rapide
Linear Technology
Linear Technology LT3755 Manuel utilisateur
Linear Technology
Linear Technology LTM8032 Guide de configuration rapide
Linear Technology
Linear Technology LT8609 Manuel utilisateur
Linear Technology
Linear Technology LTM4620A Guide de configuration rapide
Linear Technology
Linear Technology DC2007A-B Guide de configuration rapide
Linear Technology
Linear Technology DC1723A Guide de configuration rapide
Linear Technology
Linear Technology 1215 Manuel utilisateur
Linear Technology
Linear Technology DC1366B Manuel utilisateur
Linear Technology
Linear Technology DC1041A-A Guide de configuration rapide
Linear Technology
Linear Technology DC116 Series Guide de configuration rapide
Linear Technology
Linear Technology LTC2950-2 Manuel utilisateur
