Lindy 20775 Comment utiliser

20775 ~ Serial ATA Back Plane

Short Manual (provisional)

Introduction

The Serial ATA Back Plane is an internal drive housing that supports four (4) hot swap Serial ATA

hard drives in a three (3) 5.25” drive space. The Serial ATA Back Plane can be installed into any

PC Case, External Enclosure, or Disk Array Chassis that has available three 5.25” half-height

drive bays. It extends the storage capacity of your system and provides hot swap capability to the

Serial ATA hard drive installed. The Serial ATA Back Plane has been tested in typical desktop

system configuration with various host bus adapters and hard drives to ensure highest

compatibility. The configuration included current 7,200 rpm and 10,000 rpm drives from the

leading suppliers of disk drives.

Features

 Multi-layer backplane for high signal integrity

 Cableless drive tray design for Serial ATA

 Install (4) 3.5” LP hard drives into (3) standard 5.25” HH drive bays

 Meet Hot Swap specification for Serial ATA

 High quality aluminum housing

 Temperature controlled four-speed turbo blower for 10K/15K rpm HDDs (SATA)

 Microprocessor controlled sequential drive power-up (SATA)

 Visual and audible indicators for fan fail and overheat situations

 Auxiliary 3.3V power source for additional SATA devices

Specifications

Dimensions: 239 mm x 148 mm x 128 mm (D x W x H)

Weight: Approximately 2.2 kg (without drives)

Operating Temperature: 0°C ~ 55°C

Non-Operating Temperature: Non-Operating Temperature:

Installation

Setup and Operation

LED Indicators

There are four HDD status LED’s and one Fan / Temperature status LED on ASWAP as shown in Figure 2.

The functions of these LED are described in the table below: *

*Attention: HDD ACCESS LED Function is now reserved

LED Messages

HDD Status LED

LED Color Status

GREEN Hard drive is present and ready

RED Hard drive is not present or defective

Fan / Temperature Status LED

GREEN Fan is normal and no overheating

RED

Fan failed or temp. over the setting on CN3

Installation of HDD in Carrier

Installation of HDD in PC-Case

LED indicators

Overheat temperature setting ***

Jumper CN3 sets the overheating threshold temperature. There are three settings: 45°, 55° (default) or

65°C. Once the sensor on the backplane detects the operating temperature is over the setting. Audio alarm

buzzer will sound and Fan / Temperature LED will turn red. You can turn off the alarm buzzer by press the

mute bottom with a pointed object.

CN3 for choosing the temperature for audio alarm

45ºC 55ºC 65ºC

Delayed HDD start setting **

The HDDs can be started one by one. The start up mode can be set via JP4.

JP4 SETTING TABLE (for HDD start up mode)

Delay1(PIN 1,2) Delay2(PIN3,4)

All start (together) OPEN OPEN

Delay 1 sec (one by one) CLOSED OPEN

Delay 1.5 sec (one by one) OPEN CLOSED

Delay 2 sec (one by one) CLOSED CLOSED

**Attention: This Function is now reserved

*** Attention: This Function is now reserved The Functions will be ready by Shipment in August 2003

JP4 for sequent starting of HDDs

Table des matières

Autres manuels Lindy Enceinte

Lindy

Lindy 20694 Manuel utilisateur

Lindy

Lindy Mini NAS Enclosure SATA & IDE 42808 Manuel utilisateur

Lindy

Lindy 43104 Manuel utilisateur

Lindy

Lindy 3.5” IDE Manuel utilisateur

Lindy

Lindy 43285 Manuel utilisateur

Lindy

Lindy 42937 Manuel utilisateur

Lindy

Lindy 42706 Manuel utilisateur

Lindy

Lindy 42827 Manuel utilisateur

Lindy

Lindy 43184 Manuel utilisateur

Lindy

Lindy 43115 Manuel utilisateur

Lindy

Lindy 42714 Manuel utilisateur

Lindy

Lindy 43125 Manuel utilisateur

Lindy

Lindy 43186 Manuel utilisateur

Lindy

Lindy 43288 Manuel utilisateur

Lindy

Lindy 42831 Manuel utilisateur

Lindy

Lindy 42840 Manuel utilisateur

Lindy

Lindy 42671 Manuel utilisateur

Lindy

Lindy Network Device 42807v0 Manuel utilisateur

Lindy

Lindy 43108 Manuel utilisateur

Lindy

Lindy 43103 Manuel utilisateur

Lindy

Lindy 42911 Manuel utilisateur

Lindy

Lindy 42672 Manuel utilisateur

Lindy

Lindy 43097 Manuel utilisateur

Lindy

Lindy 20688 Manuel utilisateur

Manuels Enceinte populaires d'autres marques

SilentiumPC

SilentiumPC Armis AR5 Manuel

Pulsar

Pulsar 17/TRP80/DSPR Manuel utilisateur

Thermaltake

Thermaltake V150 TG Manuel utilisateur

MSI

MSI MPG SEKIRA 500X Manuel utilisateur

Antec

Antec Dark fleet DF-10 Manuel utilisateur

Nexans

Nexans WTC05 Manuel utilisateur

Peavey

Peavey DS 1502 Manuel utilisateur

D-Link

D-Link ShareCenter Pro DNS-1550-04 Manuel utilisateur

Rosewill

Rosewill RX82-U(JBOD) Manuel utilisateur

QNAP

QNAP SAS JBOD CLI 1.0 Manuel utilisateur

GAMDIAS

GAMDIAS Talos P1 Manuel utilisateur

Auvs

Auvs KR615 Manuel utilisateur

Digitus

Digitus DA-71114 Manuel utilisateur

CommScope

CommScope FDH 3000 Manuel utilisateur

FS

FS FHD-FWME4 Manuel utilisateur

JBL

JBL CS1215T Manuel utilisateur

Pulsar

Pulsar ARAD-S4 Manuel utilisateur

Pulsar

Pulsar AWO454 Manuel utilisateur