Linddana TP 250 Manuel utilisateur

Linddana A/S . Ølholm Bygade 70 . DK-7160 Tørring . T +45 75 80 52 00 . tp@linddana.com . www.linddana.com

User Manual

Spare parts catalogue

for the TP 250 wood chipper in

the park series

Linddana A/S . Ølholm Bygade 70 . DK-7160 Tørring . T +45 75 80 52 00 . tp@linddana.com . www.linddana.com

1Introduction

Congratulations on your new TP wood chipper.

Linddana produces TP wood chippers of the finest quality by using the most modern production

technologies, i.a. laser cutting, CNC technology and robot technology in bright and open

production facilities.

For safety reasons and in order to get maximum pleasure from the wood cutter, it is important to

read these instructions before use.

The user manual explains about safety, use and maintenance so that the work with the wood

chipper will be safe and profitable.

This manual has been translated from Danish.

Linddana A/S

Jørgen Due Jensen, Managing director

Your distributor is always available with spare parts, advice and guidance.

Distributor stamp

Linddana A/S . Ølholm Bygade 70 . DK-7160 Tørring . T +45 75 80 52 00 . tp@linddana.com . www.linddana.com

2EU declaration of conformity.

Manufacturer:

LINDDANA A/S, Ølholm Bygade 70, Ølholm, 7160 Tørring, Denmark

hereby declares that

______________________________________________

Wood chipper:

is in concordance with the provisions of the Machine Directive (Directive 06/42/EC) and with the

national legislation which translates this directive;

is in concordance with the following other EC Directives:

2000/14/EC

Furthermore it is stated that

EN 13525 (harmonised standard), has been used.

Title: Managing director

Name: Jørgen Due Jensen

Ølholm, 02 November 2015

Linddana A/S . Ølholm Bygade 70 . DK-7160 Tørring . T +45 75 80 52 00 . tp@linddana.com . www.linddana.com

3Table of content

1Introduction .................................................................................................... 2

2EU declaration of conformity........................................................................... 3

3Table of content .............................................................................................. 4

4Use .................................................................................................................. 5

5Mounting instructions ..................................................................................... 6

5.1 Before use ............................................................................................................................6

5.2 Mounting instruction...........................................................................................................8

6Safety instructions........................................................................................... 9

6.1 Safety regulations ................................................................................................................9

6.2 Pictograms used.................................................................................................................11

6.3 Noise level..........................................................................................................................13

6.4 Environmental instructions ...............................................................................................13

7Operation of the machine ............................................................................. 14

7.1 Table 1 Regulating the number of revolutions for the retract rollers ..............................15

8Maintenance ................................................................................................. 16

8.1 Maintenance schedule.......................................................................................................16

8.2 Lubrication and oil .............................................................................................................17

8.3 Maintenance of the retract rollers....................................................................................18

8.4 Changing worn parts ..........................................................................................................19

8.5 Grinding of knives ..............................................................................................................25

9Special instruction for TP 250 MOBILE TURNTABLE ....................................... 26

10 Hydraulics diagram, TP 250 without revolution guard................................ 29

11 Hydraulics diagram TP 250 with revolution guard ...................................... 29

12 Instruction for revolution guard TP PILOT 01.............................................. 30

12.1 Overall operation ...............................................................................................................30

12.2 Programming .....................................................................................................................32

12.3 Mounting............................................................................................................................36

12.4 Technical data ....................................................................................................................37

13 Troubleshooting for wood chipper TP 250.................................................. 38

14 Warranty obligation for wood chipper ....................................................... 39

15 Technical data wood chipper ..................................................................... 41

16 Accessories ................................................................................................ 43

17 Spare parts catalogue................................................................................. 43

Linddana A/S . Ølholm Bygade 70 . DK-7160 Tørring . T +45 75 80 52 00 . tp@linddana.com . www.linddana.com

4Use

The TP 250 wood chipper is designed for stationary wood chipping in the form of braches etc.

The machine must not be used for materials containing stone, metal or other foreign bodies.

These foreign bodies can in the best case dull the knives and in the worst case break the machine.

Knives and anvil can break when stone or metal comes in between them.

The machine must not be used for wood chipping of wood containing nails, screws, arming etc.

When feeding branches you must stand next to the feeding hopper (see fig. 1).

The branches can be thrown around when the retract rollers get a hold of them.

Logs must be fed into the machine from the back (see fig. 2).

Figure 1 Feeding branches Figure 2 Feeding logs

Remember to keep the knives and anvil sharp, it makes feeding easier and gives a better quality

chips, and besides it lovers the use of fuel considerably.

The machine must be inspected daily, meaning the rotor housing must be opened and the rotor,

knives, anvil etc. must be inspected. By doing this you prevent unexpected stops and prolong the

life of the machine.

The tractor or trailer upon which the machine is mounted must always have the brakes activated

during work.

The machine must not:

·Be used for other materials than wood

·Be used to push trees, stubs etc.

There must not be equipment like forest chains, axes, chain saws etc. in the feeding hopper.

Linddana A/S . Ølholm Bygade 70 . DK-7160 Tørring . T +45 75 80 52 00 . tp@linddana.com . www.linddana.com

5Mounting instructions

5.1 Before use

The machine is equipped with a lifting point which is to be used when lifting the machine with a

crane or any other hoisting device (ground assistance) (see Fig. 3). The machine can also be lifted

with a fork lift truck. This is done by using the holes made for this purpose on both sides of the

foot (see fig. 4). Make sure that the forks of the truck are put all the way through otherwise the

machine can tip over. The TP 250 MOBILE TURNTABLE is mainly transported on the trailer wheels,

but it can also be lifted with a fork lift truck under the trailer bearers (see fig 5).

Figure 3 Lifting point on the machine

Figure 4 Lifting with a fork lift truck

Lifting point

Linddana A/S . Ølholm Bygade 70 . DK-7160 Tørring . T +45 75 80 52 00 . tp@linddana.com . www.linddana.com

Figure 5 Lifting with a fork lift truck

Store the manuals for the PTO member with this manual in the manual box on the machine.

Before operation you must check that the wood chipper cleared of foreign bodies. The machine

must be uncoupled from the tractor’s PTO, and for the MOBILE models, the key must be removed

from the ignition before opening for the rotor. Check that the rotor is at a complete standstill.

Turn the ejector tube so that it faces the opposite direction of the rotor housing (see fig. 6).

Loosen the

bolts that hold the upper and lower rotor housing together. Lift the top part of the rotor housing

up until the ejector tube rests on its own. Turn the rotor a few times by hand. Remove any foreign

bodies.

Check that the gap between the knives and the anvil is correct = 0,7mm. The knives have a fixed

knife position = 13 mm. Check that the knives are not rubbing on the anvils.

Lift the top part of the rotor housing back in place and tighten the bolts.

Check that all bolts, nuts and screws are tightened properly.

Remember to lubricate all the lubrication points (see maintenance schedule, page 16).

Old hydraulics and motor oil and used oil filters and air filters must be handed in at an approved

receiving station.

Figure 6

Position of ejector tube

when opening rotor

Linddana A/S . Ølholm Bygade 70 . DK-7160 Tørring . T +45 75 80 52 00 . tp@linddana.com . www.linddana.com

5.2 Mounting instruction

The machine is designed to be mounted on the tractor’s three-point-suspension or trailer

mounted with its own engine.

Machines for mounting on the tractor’s three-point-suspension is delivered with a PTO axle with

either 1 3/8" - 6 splines or 1 3/8" - 21 splines.

At 1000 rpm, certain types of tractors a PTO axle with 1 3/8" - 21 splines must be used.

The PTO axle must be mounted with free running on the machine side.

Linddana uses Walterscheid 2400 with free running which comes with the machine.

The length of the PTO axle has to be adapted to the tractor following instructions from the

supplier of the PTO axle. See the attached manual for the PTO axle.

The machine must stand on a plane, horizontal surface during use and the tractor mounted

machines must be attached to the tractor’s three-point-suspension (see fig. 7). The tractor’s

brakes must be properly activated. Trailer mounted machines must also have their brakes

activated (see fig. 8).

When starting the machine: Engagement must be done with the motor running at idle speed or at

as few revolutions as possible in order to avoid overloading of the PTO axle, gear box, tractor and

wood chipper.

Figure 7 TP 250 PTO three-point-suspension Figure 8 TP 250 MOBILE hand brake

Hand brake

Three-point-

suspension

Linddana A/S . Ølholm Bygade 70 . DK-7160 Tørring . T +45 75 80 52 00 . tp@linddana.com . www.linddana.com

6Safety instructions

6.1 Safety regulations

·Use hearing protectors, safety goggles or a similar eye protection, close fitting safety

clothing and safety shoes.

·When working near roads it can be prudent to wear a west whish reflects the light to be

more visible to the other road-users. The displaying of signs must be in accordance with

the Road Traffic Act.

·Minimum age for users of the machine is 18, for training and under surveillance from an

adult the age is 16.

·During operation, all body parts must be kept away from the feeding hopper and any

moveable parts of the machine.

·Always stand next to the feeding hopper during feeding of the machine. Always observe

the terrain conditions around the machine. It can be dangerous to fall near the machine!

·Before starting the machine check that the safety devices are working properly. Especially

the stop and return functions on the operation bow.

·The machine must not be started without the ejector tube mounted to the machine.

·Never use the machine in closed or poorly ventilated spaces, because of the danger of

carbon monoxide poisoning.

·The top part of the machine as well as all other shielding must not be opened/removed

before the rotor disc is completely immovable and the tractor’s motor is stopped.

·Always stop the machine and the tractor during inspections, service or repairs. The

machine must be uncoupled from the tractor’s PTO.

·Tractor mounted machines have to be on the ground before service or repairs are done.

·Always remove the keys from the machine and/or the tractor before leaving it.

·After maintenance and repairs, the machine must not be started before all bolts are

tightened and all safety devices are mounted.

·Three-point mounted machines must be coupled to the tractor’s three-point- suspension

before use.

·The maximum rpm for the machine (1000 rpm) must not be superseded.

·The transmission axle’s tube shielding and covering must always be intact. Safety chains on

the transmission axle have to be properly mounted.

·The length of the PTO axle has to be adapted to the tractor according to the

recommendations from the supplier of the PTO axle.

·The ejector tube must not point towards people or areas where there are people. There is

a safety distance of 20 m. in the direction where the chips are thrown.

·AT DANGER: PUT THE OPERATION BOW IN NEUTRAL (See fig. 10)

Linddana A/S . Ølholm Bygade 70 . DK-7160 Tørring . T +45 75 80 52 00 . tp@linddana.com . www.linddana.com

·During operation the machine’s height may not supersede 600 mm over the terrain (see

fig. 9). If this height is not maintained the operation/safety handle will not work as it

should, and

that may lead to risks of severe personal injury due to retraction.

Figure 9 Maximum height over the terrain

·During transport or when the machine is dismantled, the PTO axle has to be placed in the

machine’s carrier bow.

·In case of transport on roads the ejector tube is turned so it is placed appropriately within the

width of the machine and then it is fixed securely.

·During transport on public roads, the provisions of the authorities must be respected.

·During cleaning of the hopper, THE RETRACT ROLLERS MUST BE STOPPED.

·For cleaning a broom or similar must be used. Never touch the inside of the hopper when the

machine is running.

SPECIAL: TP 250 PTO K

·The machine must not be fed by hand since it has been designed for feeding by a crane.

·There is a security zone of 20 m around the tractor and the wood chipper. During operation no one

except the driver of the tractor is allowed in this area.

·If people should come inside the security zone by accident, the emergency stop which stops all

movement by the crane and feeding into the wood chipper must be pressed immediately. The

emergency stop should always be activated when the driver leaves the driver’s cab.

·AT DANGER: AKTIVATE THE EMERGENCY STOP IN THE TRACTOR

Table des matières

Manuels Autre populaires d'autres marques

GO Industries

GO Industries 38017 Manuel utilisateur

Cissell

Cissell 30LBCMAN2 Manuel utilisateur

RIDGID

RIDGID K-60SP Manuel utilisateur

Gage Bilt

Gage Bilt GB751SH-5 Manuel utilisateur

OVE

OVE SIERRA 60 Manuel utilisateur

ReelCraft

ReelCraft 7800 OLB21 Manuel utilisateur

Body Armor 4x4

Body Armor 4x4 ECO-SERIES Manuel utilisateur

ROBLIN

ROBLIN DROP Guide de l'utilisateur

EMG

EMG EMG-ACB BARREL Manuel de service

MiniSolar

MiniSolar MT-150 Manuel utilisateur

Parkside

Parkside PSZ 250 B2 Manuel utilisateur

ABB

ABB REM 610 Manuel du produit

Parkside

Parkside 55992 Manuel du propriétaire

Skyjacker

Skyjacker F250 Manuel utilisateur

IBM

IBM IBM SYSTEM Z Guide d'installation

Grech Motors

Grech Motors G28 Manuel utilisateur

NOVAK

NOVAK BATTERY CARE SHEET Mode d’emploi

Telemotive

Telemotive blue PiraT Mini Guide de l'utilisateur