Lincoln G Series Manuel utilisateur
DESCRIPTION
Model 1810
MANUAL CENTRO-LUBER,
GREASE PUMP
Series "G"
The 1810 Centro-Luber is a manually operated multiple stroke grease pump for use on machines where periodic manual
lubrication is acceptable. It is used as the pumping unit for a centrali ed lubrication system having a single line circuit of
Series SL-1, SL-32, or SL-33 Injectors. Injectors can be used in combination where bearing si es or lubricant requirements
indicate such a combination advantageous and most efficient.
Pump dispenses grease up through NLGI #1 and discharges an established amount (*.160 cu. in.) into the circuit for each
full stroke of the pump handle. A built-in cycle indicator in the pump shows completion of the lubrication cycle.
*Based on lubricants that are free of entrapped air. Lubricants that are specifically aerated will reduce output of pump.
Model 1810 has a spring loaded follower in the reservoir and is filled with a filler pump through a filler fitting.
SPECIFICATIONS
LUBRICANT
OUPUT RESERVOIR
CAPACITY LUBRICANT
OUTLET
LUBRICANT OPERATING PRESSURE (PSI)
INJECTOR
SYSTEM MINIUM MAXIMUM RECOMMENDED
* .160 cu in.
per stroke 5 lb.
(150 cu. in.) 1/4" NPTF
Female
SL-1 1,850 3,500 2,500**
SL-32
SL-33 1,200 3,500 2,500**
SUPPLY LINE SPECIFICATIONS
1810
CENTRO-LUBER CENTRALLY
LOCATED ON MACHINE
FOR CONVENIENCE
OF FILLING AND
OPERATION
Section
Page
- C8
- 62K
APR - 96
TO FILL MODEL 1810 WITH FILLER PUMP
1) Use a manual filler pump to fill reservoir through the filler fitting in the
pump body. Attach coupler on delivery hose to filler fitting. Stroke filler
pump handle until lubricant weepage is noted at air vent hole in the
reservoir (lower portion of follower must rise beyond air vent hole to expel
entrapped air from lubricant).
NOTE: When filling the reservoir, caution should be used, as extreme
pressure can cause damage to reservoir and follower assembly.
) A strainer is behind the filler fitting to prevent foreign material from
entering the reservoir. Remove filler fitting to inspect and clean strainer
periodically.
**Pressure i dicator of pump set at factory.
One Lincoln Way
St. Louis, Missouri 63120-1578
(314 679-4200
Copyright 1996
Printed in U.S.A.
SEAMLESS STEEL
TUBE SIZE
MAXIMUM LENGTH OF
SUPPLY LINE GREASE
NLGI #0 NLGI #1
3/8" O.D. x .028" Wall 50 Ft. 25 Ft.
AIR VENT
HOLE
RESERVOIR
FILLER
FITTING
COUPLER
FILLER PUMP
DELIVERY
HOSE
A+B+C+D+E+F must not exceed maximum supply line
length shown above.
FORM 402621
Form 402621 Page 2
Assembly Note:
Loosely install 16650 and 31128
onto 91613. Then install 91613 into
40434 and tighten to 75 ft-lbs.
Tighten 16650 to 60 ft-lbs.
© Indicates change
TO PRIME SYSTEM
S PPLY LINES
After pump reservoir has been filled with recommended lubricant, turn vent plug counterclockwise one complete turn
and operate pump until lubricant flows freely from opening in vent plug to expel air pockets trapped between the pump
and the supply line connection. Tighten vent plug. Remove all plugs in dead ends of the injector manifolds and supply
lines. Operate pump until lubricant flows from any plug opening. Close opening with plug. Continue operating pump
until lubricant flows from another plug opening. Repeat this procedure until all supply lines are primed and plug openings
closed.
FEEDER LINES
Fill each feed line with lubricant before connecting lines to outlet of injectors and bearings. This will prevent having
to cycle each injector for every inch of feed line between injector and bearing.
INJECTORS
Check each individual injector for proper operation. Injector stem moves when injector discharges lubricant to bearing.
This may require cycling system several times. After checking injectors for operation adjust injectors for the volume
required for each individual bearing.
Form 402621 Page 3
SECTION A - A
PART QTY. DESCRIPTION
10127 1Vent plug
12511 1Pipe plug
12635 1 Pin
12637 1Indicator extension
12638 1Packing retainer
12639 1Spring housing
12640 1 Indicator pin
13068 1Toggle
13069 1Eccentric cam
13310 1 Pin
13348 3Tie rod
14359 1Bushing
16395 1Handle
16650* 1Check stop
31104* 1Gasket
31128* 1Gasket
34122* 1Packing (Nitrile)
34230* 1O-ring (Nitrile)
34231* 1Packing (Nitrile)
34274* 1Gasket (Neoprene)
35117* 1Packing (Nitrile)
40408 1Handle casting
40434 1Pump body casting
40435 1 Cover
45939 2Follower guide
50044 2Screw
50531 1Set screw
51003 1Jam nut
51015 1Jam nut
51022 3 Nut
55305* 2Spring
57055 1Spring
57057 1Snap ring
66765 4Retaining ring
66924 2Retaining ring
69217 1 Cotter pin
70397 1Knob
70485* 1Ball
91142 1Indicator assembly
91613 1Bushing &plunger assembly
242260* 1O-ring (Nitrile)
247210 1Reservoir assembly (Acrylic)
SERVICE PARTS
* Recommended service
parts inventory
Form 402621 Page 4
RESERVOIR
HANDLE
INDICATOR
SUPPLY LINE
TO INJECTORS
1st OPERATION
2nd OPERATION
OPERATION
The Centro-Luber System lubrication cycle consists of two
operations:
1st OPERATION
The outward stroke of the handle forces lubricant into
the supply line. As handle is operated, lubricant pressure
is built up until it reaches ,500 PSI. When this pressure
is reached, the indicator will move out to its extended
position exposing a red ring on the indicator stem. This
indicates that the necessary pressure needed to operate
the system has been reached and operation of pump
handle is no longer required.
Lubricant pressure built up in the supply line operates the
injectors which dispense a measured amount of lubricant
into the bearing.
2nd OPERATION
Release handle and return it to its normal position
against the reservoir. When handle is in this position
lubricant pressure in the system vents back into the
reservoir. handle must be released for pump to vent.
Operators hand, gripping the handle, prevents the pump
from venting between strokes. Injectors re-charge for
next lubrication cycle.
PUMPING
RANGE
VENTING
POSITION
HANDLE
50531
SET SCREW
13069
ECCENTRIC
CAM
51003
NUT
CENTRO-LUBER IS ALWAYS VENTED EXCEPT DURING PUMPING PERIOD
To adjust Vent Position of Handle loosen the 50531 Set Screw. Then unthread the 51003 Nut
approximately one full turn. The 13069 Eccentric Cam can then be moved to the desired vent
postion. Re-tighten nut and set screw.
NOTE: t may be necessary to try several positions of eccentric cam before desired venting
adjustment is obtained.
RETAIN THIS INFORMATION FOR FUTURE REFERENCE
When ordering replacement parts list: Part Number Description Model Number and Series Letter.
LINCOLN provides a Distributor Network that stocks equipment and replacement parts.
VENT PLUG
SUPPLY LINE
TO INJECTORS
RESERVOIR
HANDLE
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Lincoln Pompe à eau
Lincoln
Lincoln 84951-BK Manuel utilisateur
Lincoln
Lincoln 84852 Guide de dépannage
Lincoln
Lincoln PMA-1 Manuel utilisateur
Lincoln
Lincoln B Series Manuel utilisateur
Lincoln
Lincoln 84050 Manuel utilisateur
Lincoln
Lincoln Pile Driver III D Series Manuel utilisateur
Lincoln
Lincoln P 203 Manuel utilisateur
Lincoln
Lincoln 2385 Manuel utilisateur
Lincoln
Lincoln 85622 Manuel de la liste des pièces
Lincoln
Lincoln A Series Manuel utilisateur
Lincoln
Lincoln 83668 Manuel utilisateur
Lincoln
Lincoln POWERMASTER III Manuel utilisateur
Lincoln
Lincoln 282050 Manuel du propriétaire
Lincoln
Lincoln A Series Manuel utilisateur
Lincoln
Lincoln D Series Manuel utilisateur
Lincoln
Lincoln ZPU 08 Manuel utilisateur
Lincoln
Lincoln J Series Manuel du propriétaire
Lincoln
Lincoln FlowMaster C Series Manuel du produit
Lincoln
Lincoln QUICKLUB 203 Manuel utilisateur
Lincoln
Lincoln SKF FlowMaster II A Series Mode d’emploi
Manuels Pompe à eau populaires d'autres marques
Sykes AmeriPumps
Sykes AmeriPumps GP100M Guide de dépannage
DUROMAX
DUROMAX XP WX Series Manuel utilisateur
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 Manuel utilisateur
Franklin Electric
Franklin Electric IPS Manuel utilisateur
Xylem
Xylem e-1532 Series Manuel utilisateur
Milton Roy
Milton Roy PRIMEROYAL Manuel utilisateur