Lightware DVI-OPT-TX220-ST-Pro Manuel utilisateur

www.lightware.eu Firmware version: 1.1.3

For technical support contact [email protected] Document revision: 1.1

DVI-OPT-TX220-ST-Pro

Quick Start Guide

Installation

1. Connect the DVI source (e.g. computer) to the DVI INPUT connector.

2. Connect a compatible Lightware fiber receiver unit to the FIBER OUTPUT by using an ST

connector equipped multimode fiber cable.

3. Optionally connect a display device to the LOCAL MONITOR OUTPUT connector.

4. Connect the IEC power cable to the transmitter.

5. Select the EDID to emulate depending on the desired display resolution.

6. Power on the DVI source (e.g. computer). It will read the EDID from the transmitter,

thereafter it will output the video signal according to the set resolution.

7. Power on the fiber receiver and the connected display devices. They will display the picture

from the DVI source (e.g. computer).

Checking emulated EDID

1. Use the left (◄) and right (►) buttons to select the Emulated EDID menu.

2. In the lower line, three messages toggle automatically showing the preferred resolution, the

name of the display and a three letter abbreviation assigned to the manufacturer.

Selecting an EDID

1. Use the left (◄) and right (►) buttons to select the Switch EDID menu.

2. Use the up (▲) and down (▼) buttons to select the desired memory slot. Hold down the

buttons to scroll faster.

3. Press ENTER to emulate selected EDID.

4. The EDID change is confirmed with a following message: „EDID switched!”

Learning EDID

1. Use the left (◄) and right (►) buttons to select the Learn EDID menu.

2. Use the up (▲) and down (▼) buttons to select a memory slot (it will be overwritten). Hold

down the buttons to scroll faster.

3. Press ENTER to learn EDID to the selected memory slot from the last attached monitor on

the LOCAL MONITOR OUTPUT.

4. The EDID learn is confirmed with a following message: „EDID learned!”

EDID Memory #00: Transparent EDID operation, the last attached monitor's EDID is repeated at

the DVI INPUT.

Factory Preset EDID list

Memory

Resolution

Memory

Resolution

#01

640 x 480 @ 60.0 Hz

#26

1600 x 1200 @ 50.0 Hz

#02

640 x 480 @ 75.0 Hz

#27

1600 x 1200 @ 60.0 Hz

#03

848 x 480 @ 60.0 Hz

#28

1920 x 1200 @ 59.55 Hz

#04

800 x 600 @ 50.0 Hz

#29

1920 x 1200 @ 50.0 Hz

#05

800 x 600 @ 60.30 Hz

#30

1440 x 480i @ 60.3 Hz

#06

800 x 600 @ 74.99 Hz

#31

640 x 480 @ 59.94 Hz

#07

1024 x 768 @ 49.98 Hz

#32

720 x 480 @ 59.92 Hz

#08

1024 x 768 @ 60.0 Hz

#33

1440 x 576i @ 50.6 Hz

#09

1024 x 768 @ 75.2 Hz

#34

720 x 576 @ 50.0 Hz

#10

1152 x 864 @ 75.0 Hz

#35

1280 x 720 @ 50.0 Hz

#11

1280 x 768 @ 50.0 Hz

#36

1280 x 720 @ 60.0 Hz

#12

1280 x 768 @ 59.92 Hz

#37

1920 x 1080i @ 50.3 Hz

#13

1280 x 768 @ 75.0 Hz

#38

1920 x 1080i @ 50.0 Hz

#14

1360 x 768 @ 60.1 Hz

#39

1920 x 1080i @ 60.5 Hz

#15

1364 x 768 @ 50.0 Hz

#40

1920 x 1080 @ 24.0 Hz

#16

1364 x 768 @ 59.93 Hz

#41

1920 x 1080 @ 24.99 Hz

#17

1364 x 768 @ 74.98 Hz

#42

1920 x 1080 @ 30.0 Hz

#18

1280 x 1024 @ 50.0 Hz

#43

1920 x 1080 @ 50.0 Hz

#19

1280 x 1024 @ 60.1 Hz

#44

1920 x 1080 @ 49.99 Hz

#20

1280 x 1024 @ 75.1 Hz

#45

1920 x 1080 @ 60.0 Hz

#21

1366 x 1024 @ 59.99 Hz

#46

2048 x 1080 @ 49.99 Hz

#22

1400 x 1050 @ 49.99 Hz

#47

2048 x 1080 @ 50.0 Hz

#23

1400 x 1050 @ 59.99 Hz

#48

2048 x 1080 @ 59.99 Hz

#24

1400 x 1050 @ 75.0 Hz

#49

Universal EDID*

#25

1680 x 1050 @ 59.99 Hz

#50

Reserved

* Universal EDID (address #49) allows multiple resolutions including all common VESA

defined resolutions. In addition, it also features audio support.

User Memory EDIDs

EDIDs can be learned or uploaded to memory slots #51 .. #99 (referred as U1 .. U49 in

Matrix Controller software)

www.lightware.eu Firmware version: 1.1.3

For technical support contact [email protected] Document revision: 1.1

DVI-OPT-TX220-ST-Pro

Quick Start Guide

Power LED

Lights green when the unit is powered on.

Menu display

Displays status information and menu operation.

Menu navigation

Up (▲), down (▼), left (◄), right (►) and ENTER buttons.

Laser LED

Indicates when the laser driver is enabled.

Signal LED

Indicates when a valid DVI signal is detected on the DVI

INPUT connector.

Source LED

Indicates that a powered-on DVI source is connected to the

unit (detects +5V signal on Pin 14 of the input DVI

connector).

AC connector

Standard IEC-320 C14 power connector.

Serial port

D-SUB connector. The device is controllable via RS-232

connection.

ST connector

Connect a compatible Lightware fiber receiver unit by using

an ST connector equipped multimode fiber cable.

DVI input

Connect single link DVI source.

Monitor output

A local display device can be connected to monitor the

outgoing signal.

Laser LED

Green LED indicates enabled laser driver to help to avoid

accidental look into the laser beam.

Power LED

Menu display

Menu navigation

Laser LED

Signal LED

Source LED

DVI input

AC connector

ST connector

Serial port

Monitor output

Laser LED

Autres manuels Lightware Extenseur

Lightware

Lightware DVI-OPT-RX220-Pro Manuel utilisateur

Lightware

Lightware WP-HDMI-TPS-TX97-EU Manuel utilisateur

Lightware

Lightware OPTJ Power tray Series Manuel utilisateur

Lightware

Lightware Modex-Tx Manuel utilisateur

Lightware

Lightware DP-OPT-TX150 Manuel utilisateur

Lightware

Lightware HDMI-TPS-TX95 Manuel utilisateur

Lightware

Lightware FP-HDMI-TPS-RX97-GB3 Manuel utilisateur

Lightware

Lightware WP-UMX-TPS-TX120-US Black Manuel utilisateur

Lightware

Lightware VINX-120-HDMI-ENC Manuel utilisateur

Lightware

Lightware DVIDL-OPT-TX200 Manuel utilisateur

Lightware

Lightware HDMI-TPS-TX210 Manuel utilisateur

Lightware

Lightware DVI-TP-RX100 Manuel utilisateur

Lightware

Lightware VINX-120-HDMI-ENC Manuel utilisateur

Lightware

Lightware UMX-OPT-TX150R Manuel utilisateur

Lightware

Lightware UMX-TP-TX100R Manuel utilisateur

Lightware

Lightware MODEX Manuel utilisateur

Lightware

Lightware HDBaseT HDMI-TPS-RX110AY-Plus Manuel utilisateur

Lightware

Lightware HDMI-TPS-TX97 Manuel utilisateur

Lightware

Lightware UMX-TPS-TX120 Manuel utilisateur

Lightware

Lightware HDMI20-OPTC series Manuel utilisateur

Lightware

Lightware UBEX-PRO20-HDMI-F100 Manuel utilisateur

Lightware

Lightware UBEX Series Manuel utilisateur

Lightware

Lightware EDID MANAGER V4 Manuel utilisateur

Lightware

Lightware HDMI-TPS-TX210 Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur