Lightware DVI-OPT-RX220-Pro Manuel utilisateur

www.lightware.eu Firmware version: 1.1.1

For technical support contact support@lightware.eu Document revision: 1.1

DVI-OPT-RX220-Pro

Quick Start Guide

Installation

1. Connect the DVI display devices to the DVI OUTPUT connectors.

2. Connect a compatible Lightware fiber transmitter unit with a multimode fiber cable to the

FIBER INPUT connector. Connect an LC optical cable to the “channel B” LC connector, or

use a Neutrik OpticalCON cable.

3. Power on the fiber transmitter, and the DVI source (computer).

4a. To use the built-in power supply: set the power selector switch to “I”, and connect the IEC

power cable. Now the unit is ready to be used.

4b.To power the unit remotely: works only if the receiver is connected to a

DVI-OPT-TX220-PRO with a Neutrik hybrid fiber cable. Set the power selector switch to “II”.

5. Power on the connected display devices. They will display the picture from the DVI source

(computer).

Power LED

Lights if the unit is powered on.

Laser LED

Green light indicates that the laser is properly detected on

the optical input. Red blinking light indicates low laser level,

or no incoming signal.

Signal LED

Indicates valid DVI clock signal reception.

Monitor LEDs

Each LED indicates if a display device is connected to the

corresponding DVI output.

AC connector

Standard IEC power connector.

Break-out conn.

The break-out LC connector is internally connected to output

A of the Neutrik connector.

Neutrik connector

Channel B carries the signal to this unit’s optical receiver,

and channel A carries any optical signal to the break-out LC

connector.

Serial port

The device is controllable by Lightware Matrix Control

software via RS-232 connection.

Power selector

In position “I” the receiver unit is powered by its own built-in

power supply. In position “II” the receiver unit is powered

through special hybrid fiber cable, type’Neutrik 2M-4S75’.

DVI outputs

Two display devices can be connected. The resolution and

pixel clock frequency are the same on both DVI connectors.

Alarm outputs

DVI signal detection and laser detection signals with ground

reference are available on a three-pole Phoenix connector.

Power LED

Laser LED

Signal LED

Monitor LEDs

Power selector

AC connector

Neutrik connector

Serial port

Break-out connector

Alarm outputs

DVI outputs

Autres manuels Lightware Extenseur

Lightware

Lightware FP-HDMI-TPS-RX97-GB3 Manuel utilisateur

Lightware

Lightware EDID MANAGER V4 Manuel utilisateur

Lightware

Lightware VINX-110-HDMI-DEC Manuel utilisateur

Lightware

Lightware DP-OPT-TX150 Manuel utilisateur

Lightware

Lightware DVI-OPT-TX220-ST-Pro Manuel utilisateur

Lightware

Lightware WP-HDMI-TPS-TX97-EU Manuel utilisateur

Lightware

Lightware HDMI-TPS-TX95 Manuel utilisateur

Lightware

Lightware UBEX-PRO20-HDMI-F100 Manuel utilisateur

Lightware

Lightware HDMI-TPS-TX210 Manuel utilisateur

Lightware

Lightware UBEX Series Manuel utilisateur

Lightware

Lightware DVI-TP-RX100 Manuel utilisateur

Lightware

Lightware HDMI20-OPTC series Manuel utilisateur

Lightware

Lightware OPTJ Power tray Series Manuel utilisateur

Lightware

Lightware UMX-TPS-TX100 Series Manuel utilisateur

Lightware

Lightware VINX-110-HDMI-DEC Manuel utilisateur

Lightware

Lightware UMX-TPS-TX120 Manuel utilisateur

Lightware

Lightware HDMI-3D-OPT-TX210RAK Manuel utilisateur

Lightware

Lightware HDBaseT HDMI-TPS-RX110AY-Plus Manuel utilisateur

Lightware

Lightware MODEX-F15-OPTS-TX Manuel utilisateur

Lightware

Lightware Modex-Tx Manuel utilisateur

Lightware

Lightware HDMI-TPS-TX226 Manuel utilisateur

Lightware

Lightware UBEX-MMU-X200 Manuel utilisateur

Lightware

Lightware UMX-OPT-TX150R Manuel utilisateur

Lightware

Lightware WP-HDMI-TPS-RX97-EU Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur