Lightolier Lytespan ATTACHMENT Manuel utilisateur

(

INSTRUCTIONS FOR LYTESPAN ATTACHMENT FITTING

INSTRUCTION SHEET NO

lS:7589AZ

ROW

/- SILVERED CONTACT

CORD PENDANT MOUNTING

(supports up to 10 Ibs.)

I. Unscrew LEVER. Remove PLUG ASSEMBLY, HOUSING

INSERT from attachment HOUSING. See Fig. 1.

2. See “WIRING PROCEDURE” below.

STEM MOUNTING USING 1/2” O.D. TUBING

(supports up to 25 Ibs.)

I. Unscrew LEVER, STRAIN RELIEF CAP and KNURLED

RING Remove PLUG ASSEMBLY, HOUSING INSERT

from attachment HOUSING.

2. Use STEM TUBING with M-18 pipe thread

3A” long (not supplied). Screw KNURLED RING onto

STEM TUBING. See Fig. 1A.

3. Insert STEM TUBING into attachment

HOUSING and screw on LOCKNUT until secure.

Tighten KNURLED RING to lock in place.

4. See “WIRING PROCEDURE’’ below.

CHAIN MOUNTING

(supports up to 25 Ibs..)

1. Unscrew LEVER and STRAIN RELIEF CAP.

Remove PLUG ASSEMBLY, HOUSING INSERT from

attachment HOUSING.

2. Replace STRAIN RELIEF CAP with %-18 CHAIN LOOP

(not supplied). See Fig. lB.

3. See “WIRING PROCEDURE” below.

WIRING PROCEDURE

Remove 2“ of outer insulation from FIXTURE CORD

(when required) and strip conductor ends 3A”. See Fig. 1.

Insert FIXTURE CORD through attachment housing.

Fasten BLACK WIRE to LONGER (BRASS) CONTACT and

WHITE WIRE to SHORTER (SILVERED) contact. For

3conductor cord, splice GROUND LEADS with wire

connector. (If the GROUND LEAD from the attachment

HOUSING is not used, leave wire connector on.) See Fig. t

CAUTION: OBSERVE POLARITY WHEN

FASTENING WIRES. BEND WIRES AROUND

SCREW IN CLOCKWISE DIRECTION.

Pull FIXTURE CORD back through attachment HOUSING and

push HOUSING INSERT and PLUG ASSEMBLY into

HOUSING (silvered contact in PLUG ASSEMBLY facing

grooved side of attachment HOUSING). Push ground leads

into area between SPRING section. Fig. 2.

Allow fixture cord to extend into attachment HOUSING by

1/6” and tighten PLASTIC SET SCREW, Fig. 2.

CAUTION: TIGHTEN ENOUGH TO SUPPORT

ASSEMBLY.

Screw LEVER into PLUG ASSEMBLY.

‘RASSCoNTACT----kc <

‘“~ :::~;

,SJQ/

GREEN GROUND !

“~F’=

LEAD

>;, PLUG ASSEMBLY

$3 “~i

w,,,-’”

CONNECTOR

‘REEN ‘ROuND --=&

LEAD

KNURLED RING

STRAIN RELIEF

CAP

$3W27 /’-LEvER

—

SET SCREW

~~,xTuRE

CORD

FIG. 1

KNURLED

RING

CHAIN s<

LOOP

KNURLED

(by others)

~sT~~

TUBING

STEM

MOUNTING CHAIN

MOUNTING

GROOVE

LEVER

TIC SET

FIXTURE

CORD --’4 l\ SCREW

~ ~ > STRAIN RELIEF

CAP

FIG. 2

‘@ SECAUCUS, NEW JERSEY, 07096 ”0508

[m[<>[=[~<>[ml[~l~ MONTREAL, QUEBEC, CANAD~

~$js~RucT[~Ns FOR ATTACHING LyTEspA/IJ

ATTACHMENT FITTING

1. Align BEAD on LYTESPAN TRACK and GROOVE

in attachment FITTING before inserting into

LYTESPAN TRACK. See Fig.1 (If BEAD is NOT

aligned, apotential hazard may result.)

2. Unscrew the TURN KNOB partially and

position LEVER as shown in Fig. 1.

3. To attach attachment FITTING:

squeeze BUTTON and TURN KNOB,

insert into LYTESPAN TRACK, and

release. Tighten TURN KNOB. This

holds attachment FITTING to LYTESPAN

TRACK mechanically. Turn LEVER to make

electrical connection. See Fig. 2.

4. To shift fixture location on the LYTESPAN

TRACK loosen TURN KNOB slightly, release

LEVER and slide to new position.

5. To remove fixture reverse the procedure in (3),

push TURN KNOB in and allow attachment

FITTING to disengage.

6. Fixture can be left on LYTESPAN TRACK

when not in use by turning LEVER to

disconnect electrically.

INSTRUCTIONS FOR CONVERTING LYTESPAN

ATTACHMENT FITTING TO OPERATE ON (2 CIRCUIT)

LYTESPAN TRACK.

NOTE: To insure proper operation of Lytespots on Two Circuit

Lytespan Track, the BLACK SPACER

(supplied) must be used at all times on the PIU9

assembly.

The BLACK SPACER is not used when operating

Lytespots on Single Circuit Track.

LOWER CIRCUIT, FIG. 3:

Illustrates contacts in low position with spacer

in place for lower circuit.

UPPER CIRCUIT, FIG. 4 and 5:

To convert attachment fitting for upper circuit,

raise BRASS CONTACT to high position (as

indicated by dotted line) by pulling CONTACT

as high as stop permits and slipping on BLACK

SPACER as shown in Fig. 4 and 5.

_LYTESPAN TRACK

BEAO ER

BUTTON

GROOVE NG

FIG. 1

(

BUTTON ~

FIG. 2

BLACK SPACER

MOVABLE BRASS

CONTACT

FIG. 3

MOVABLE BRASS

CONTACT

STATIONARY SILVEREO

BLACK CONTACT (COMMGN)

SPACER PLUG

.ASSEMBLY

-5”” \

BLACK

SPACER

FIG. 4FIG. 5

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Lightolier Accessoires

Lightolier

Lightolier LYTESPAN CONVENIENCE OUTLET Instructions d'utilisation

Lightolier

Lightolier Lytespan 8610E Manuel utilisateur

Lightolier

Lightolier ZYLINDER GLAS Mode d’emploi

Lightolier

Lightolier LAS56 AIRSEAL GASKET KIT Manuel utilisateur

Lightolier

Lightolier Calculite C6P38A Manuel utilisateur

Lightolier

Lightolier Calculite AL4CC Manuel utilisateur

Lightolier

Lightolier C6TCAD Instructions d'utilisation

Lightolier

Lightolier 1101HLIE Manuel utilisateur

Lightolier

Lightolier 1004F26ESR Manuel utilisateur

Lightolier

Lightolier POWER EXTENSION CONNECTOR Manuel utilisateur

Lightolier

Lightolier ProSpec 26075 Manuel utilisateur

Lightolier

Lightolier Lytecaster 1001FEM Series Manuel utilisateur

Lightolier

Lightolier Lytecaster 1920LV Manuel utilisateur

Lightolier

Lightolier Lytespan 8102 Manuel utilisateur

Lightolier

Lightolier 1101HCB Manuel utilisateur

Lightolier

Lightolier 1102TH1R Manuel utilisateur

Lightolier

Lightolier ProSpec 37000 Manuel utilisateur

Lightolier

Lightolier Lytespan 8676B Manuel utilisateur

Lightolier

Lightolier Lytecaster 2095 Manuel utilisateur

Lightolier

Lightolier CL-2 Manuel utilisateur

Lightolier

Lightolier IS_CD7-STEM Mode d’emploi

Lightolier

Lightolier Lytespan 8603WH Manuel utilisateur

Lightolier

Lightolier Calculite FA-EM Manuel utilisateur

Lightolier

Lightolier Lytecaster 1178T Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur