Lightmybricks 10256 Manuel utilisateur

Light My Bricks: Taj Mahal Lighting Kit

The following page is instructions for the Light My Bricks LEGO Taj Mahal

(10256) LED light kit. You purchase this kit on our official website.

To ensure a trouble-free installation of your light kit, please read and follow

each step carefully.

Package contents:

• 8x White 30cm Bit Lights

• 9x White Strip Lights

• 2x Multi Colour Strip Lights • 1x 8-Port Expansion Board

• 6x 6-Port Expansion Boards

• 7x 30cm Connecting Cables

• 10x 15cm Connecting Cables

• 1x USB Power Cable 30cm

• 6x Adhesive Squares

LEGO Pieces

• 9x LEGO Plate 1x6 (any colour)

• 4x Plate 1x2 (any colour)

. . .

Important things to note:

Laying cables in between and underneath bricks

Cables can t in between and underneath LEGO® bricks, plates, and tiles

providing they are laid correctly between the LEGO® studs. Do NOT

forcefully join LEGO® together around cables; instead ensure they are laying

comfortably in between each stud.

CAUTION: Forcing LEGO® to connect over a

cable can result in damaging the cable and

light.

Connecting cable connectors to Expansion Boards

Take extra care when inserting connectors to ports of Expansion Boards.

Connectors can be inserted only one way. With the expansion board facing

up, look for the soldered “=” symbol on the left side of the port. The

connector side with the wires exposed should be facing toward the

soldered “=” symbol as you insert into the port. If a plug won’t t easily into

a port connector, do not force it.

Incorrectly inserting the connector can can

result in bent pins inside the port or possible

overheating of the expansion board when

connected.

Connecting cable connectors to Strip Lights

Take extra care when inserting connectors to ports on the Strip Lights.

Connectors can be inserted only one way. With the Strip Light facing up,

ensure the side of the connector with the wires exposed is facing down. If a

plug won’t t easily into a port connector, don’t force it.

Doing so will damage the plug and the connector.

Installing Bit Lights under LEGO® bricks and plates.

When installing Bit Lights under LEGO® pieces, ensure they are placed the

correct way up (Yellow LED component exposed). You can either place

them directly on top of LEGO® studs or in between.

. . .

OK, Let’s Begin!

Instructions for this Kit

1.) Start by removing the center tower as well as the second level of theTaj

Mahal.

2.) Disconnect the four towers.

3.) Take one of the towers and disconnect the roof as per below:

Take a White 30cm Bit Light and stick it underneath the roof in the centre

using an Adhesive Square.

4.) Reconnect the roof ensuring the cable from the Bit Light is facingone of

the corners, then disconnect the bottom of the tower from the below

position:

5.) Take the top of the tower and then disconnect the following piecesfrom

the bottom:

Gently pull apart the two upper round wall sections and then slip the Bit

Light cable inside.

Lay the cable down the middle of the wall sections and then close them up.

Reconnect the two lower wall sections ensuring the Bit Light cable is laid

down the middle.

Thread the end of the Bit Light Cable down the top of the round plate below

and then thread the cable down the bottom of the white dish.

Ce manuel convient aux modèles suivants

1

Autres manuels Lightmybricks Équipement d'éclairage

Lightmybricks

Lightmybricks 21333 Manuel utilisateur

Lightmybricks

Lightmybricks LEGO BMW M 1000 RR 42130 Manuel utilisateur

Lightmybricks

Lightmybricks LEGO MINI DISNEY THE HAUNTED MANSION 40521 LIGHT... Manuel utilisateur

Lightmybricks

Lightmybricks 103035 Mode d’emploi

Lightmybricks

Lightmybricks LEGO UCS OBI-WAN's JEDI STARFIGHTER 10215 LIGHT... Manuel utilisateur

Lightmybricks

Lightmybricks FKP 37 Manuel utilisateur

Lightmybricks

Lightmybricks LEGO Winter Village Station Manuel utilisateur

Lightmybricks

Lightmybricks 75339 Manuel utilisateur

Lightmybricks

Lightmybricks 76423 Manuel utilisateur

Lightmybricks

Lightmybricks Downtown Diner Lighting Kit Manuel utilisateur

Lightmybricks

Lightmybricks LEGO ORCHID 10311 LIGHT KIT Manuel utilisateur

Lightmybricks

Lightmybricks Sydney Opera House Manuel utilisateur

Lightmybricks

Lightmybricks Lighting Kit LEGO 10276 RGB Remote Controller... Manuel utilisateur

Lightmybricks

Lightmybricks LEGO 1989 Batwing Manuel utilisateur

Lightmybricks

Lightmybricks 10265 Manuel utilisateur

Lightmybricks

Lightmybricks 42156 Manuel utilisateur

Lightmybricks

Lightmybricks LEGO THE INSECT COLLECTION 21342 Manuel utilisateur

Lightmybricks

Lightmybricks LEGO Winter Village Post Office 10222 Manuel utilisateur

Lightmybricks

Lightmybricks LEGO AT-TE WALKER 75337 LIGHT KIT Manuel utilisateur

Lightmybricks

Lightmybricks LEGO OPTIMUS PRIME Manuel utilisateur

Lightmybricks

Lightmybricks 75306 Manuel utilisateur

Lightmybricks

Lightmybricks 75969 Manuel utilisateur

Lightmybricks

Lightmybricks LEGO STAR WARS VENATOR-CLASS REPUBLIC ATTACK... Manuel utilisateur

Lightmybricks

Lightmybricks Blade Runner Spinner Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur