LG GM730f Manuel utilisateur

This document is the user guide for the GM730f

Windows Mobile Pocket PC. All rights for this document are reserved by

LG Electronics. Copying, modifying and distributing this document without

the consent of LG Electronics are prohibited.

GM 730f User Guide

- English

This device is not intended for sale in the USA.

Part 15.21 statement

" Change or Modifications that are not expressly approved by the manufacturer could void

the user's authority to operate the equipment. “

Part 15.105 statement

This equipment has been tested and found to comply with the limits for a class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful interference or

television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Part 15 Class B Compliance

This device and its accessories comply with part15 of FCC rules.

Operation is subject to the following two conditions:

(1) This device & its accessories may not cause harmful interference.

(2) This device & its accessories must accept any interference received,

including interference that may cause undesired operation.

Body-worn Operation

This device has been tested for typical body-worn operations

with the distance of 0.79inches (2.0cm) from the user’s body.

To comply with FCC RF exposure requirements, a minimum separation distance

of 0.79inches(2.0cm) must be maintained from the user's body.

Additionally, Belt clips, holsters & other body-worn accessories may not contain

metallic components.

Getting Started

Installing the SIM Card and Battery

1. Installing the SIM card.

Your SIM card contains your phone number, service details and contacts and must be inserted into your

handset. If your SIM card is removed then your handset becomes unusable (except for emergency calls

depending on which Country you are in at the time) until a valid one is inserted. Always disconnect the

charger and other accessories from your handset before inserting and removing your SIM card. Slide the

SIM card into the SIM card holder. Make sure that the SIM card is properly inserted and the gold contact

area on the card is facing downwards. To remove the SIM card, press down lightly and pull it in the

reverse direction.

Note

vThe metal contact of the SIM card can easily be damaged by scratches. Pay special attention to the SIM

card while handling. Follow the instructions supplied with the SIM card.

Installing the battery.

Insert the Battery into the battery compartment as the metal contacts meet in the middle of the phone.

Push down the top of the battery until it snaps into place. Place the battery cover to the phone as shown.

Charging the Battery

Before connecting the charger to the phone you must first check the battery is installed.

Getting Started

When you recharge your phone after device switch off, the phone displays a charging animation.

When the phone is fully charged, the animation displays “Battery Charging Complete”.

When the battery is fully discharged, animation is not displayed.

During the animation displays “ Battery is too low”, you cannot power on the phone to get sufficient

power for booting.

As soon as charged power reach 1% (need 1 or 2 minutes), charging animation is displayed. And you

can power on the phone.

If you press and hold the power button for approx. 2 seconds in charging mode, the phone is turned on.

CAUTION!

• When you charge a fully discharged battery, it may take over a minute for the display to respond.

This is not a malfunction but completely normal.

(If using a USB cable, it may take over 10 minutes.)

• Do not force the connector as this may damage the phone and/or the charger.

• If you use the charger out of your own country, use an attachment plug adaptor for the proper

configuration.

• Do not remove your battery or the SIM card while charging.

• There is risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries

according to the maker's instructions.

WARNNING

• Unplug the charger from the mains and phone during lightning storms to avoid electric shock or fire.

• Make sure that no sharp-edged items such as animal teeth or nails come into contact with the

battery. There is a risk of this causing a fire.

Getting Started

Disconnecting the Charger

Disconnect the travel adapter from the phone as shown in the diagram. Make sure you pull by the plug,

not the cord.

How to Use a MicroSD Memory Card (Optional)

Lift the plastic cover which protects the microSD slot.

Insert the memory card into the slot with the metal contacts facing down. Do not force the memory

card into the slot, if the card does not slide in easily, please check that the card is being inserted the

correct way or if there is a foreign object in the slot.

Once inserted, push the memory card until you hear a

Click

, meaning that the microSD has been

correctly engaged.

Close the plastic slot protection.

Do not remove the memory card when reading/writing the memory card.

Attention:

vAvoid using the microSD memory card when the battery is low.

vWhen writing to the card, wait for the operation to complete before

removing the card.

vThe card is designed to fit easily into the system one way only.

vDo not bend the card or force it into the slot.

vDo not insert any memory cards other than microSD.

Supports up to 32GB microSD. For more information on the microSD, please

refer to the memory card instruction manual.

Memory Card Formatting

Before you start to use the memory card you have to format it. A message will pop up after you insert the

memory card notifying you to format the memory card.

Note

vUsually the microSD has already been formatted.

Turn the Device On and Off

To turn on the device, press the button. When you turn on the device for the first time, you are

asked to complete a calibration process. For more information, see “Calibrate the device” on next page.

To turn off the device, press again.

Getting Started

Reset the Device

Occasionally you may need to reset your device. A normal (or soft) reset of your device clears all active

program memory and shuts down all active programs. This can be useful when the device is running

slower than normal, or a program is not performing properly. A soft reset is also necessary after the

installation of some programs. If a soft reset is performed when programs are running, unsaved work will

be lost.

You can also perform a hard reset (also known as a full reset). A hard reset should be performed only if

a normal reset does not solve a system problem. After a hard reset, the device is restored to its default

settings—the way it was when you first purchased it and turned it on. Any programs you installed, data

you entered, and settings you customized on the device will be lost.

To perform a soft reset

• Find out Soft reset key which is small hole at the left side of your device shown enclosed by circles in

the picture below.

Use the stylus to press the reset key and hold it for a while. Your device may shut down. Press the

POWER button, the device restarts and displays the Today screen.

A soft reset of your device clears all active program memory and shuts down all active programs. This

can be useful when your device is running slower than normal, or a program is not performing properly.

A soft reset is also necessary after the installation of some programs. If a soft reset is performed when

programs are running, unsaved work will be lost.

To perform a hard reset

• A Hard Reset should only be performed after all other trouble shooting options have been exhausted.

After a hard reset, the device is restored to its default settings - the way it was when you first

purchased it and turned it on. Any programs you installed, data you entered, and settings you

customized on your device will be lost.

Power the device ON

Tap

Start

Settings

System

tab >

Clear Storage

Enter 1234 for the password twice.

Press Enter.

Select what to reset.

You have to enter your password and confirm again for hard reset. However when you forget your

password, the only way to hard reset the device is via the hard key sequence.

Power the device OFF.

Press and hold the following hard keys in sequence.

+ +

Keep pressing keys until your LCD screen turns on.

Align screen will appear if you success hard key reset.

Calibrate the Device

Calibrating the device screen involves tapping with the stylus the center of a cross as it moves around the

screen. This process ensures that when you tap the screen with your stylus, the tapped item is activated.

If your device does not accurately respond to screen taps, follow these steps to re-calibrate it:

Tap

Start

Settings

System

tab >

Screen

On the

Genera

l tab, tap

Align Screen

, and follow the instructions on the screen. After calibration is

completed, Align screen reappears. Click OK on upper right corner to return to setting mode.

Getting Started

Manage Screen Settings

The device touch screen has three orientation modes: Portrait, Landscape (right-handed), and Landscape

(left-handed). Portrait mode allows you to get a better view or a better operation of certain programs on

your device, while Landscape mode may be optimal for viewing longer text files.

vTo change the orientation, tap

Start

Settings

System

tab >

Screen

General

tab, and select the

orientation you want.

If Accelerometer Sensor is turned on (check (

LG Menu

) >

Settings

Sensor

Accelerometer

Sensor

), rotation sensor automatically perceive the orientation of your device and decide to direction

of screen display when the orientation for device is changed.

vTo smooth the edges of screen fonts for many programs, on the

ClearType

tab(tap

Start

Settings

System

tab >

Screen

), select the

Enable ClearType

check box.

vTo increase the readability or to see more content on the screen, on the

Text Size

tab

(tap

Start

Settings

System

tab >

Screen

), adjust the text size by moving the slider.

Table des matières

Manuels Téléphone portable populaires d'autres marques

Zte

Zte BLADE A520 Manuel utilisateur

Nokia

Nokia Lumia 620 Manuel utilisateur

Blackbe;rry

Blackbe;rry KEYone Manuel utilisateur

Bea-fon

Bea-fon X5 Premium Manuel utilisateur

Blackbe;rry

Blackbe;rry 8707 Series Manuel utilisateur

Blackbe;rry

Blackbe;rry Storm Mode d'emploi

LifeWatch

LifeWatch V Manuel utilisateur

Bea-fon

Bea-fon SILVER LINE SL860 Manuel utilisateur

IKI Mobile

IKI Mobile KF4.5i Manuel utilisateur

Hitech

Hitech HT-850 Manuel utilisateur

Yezz

Yezz Fashion F10 Manuel utilisateur

Point Mobile

Point Mobile PM60 Manuel utilisateur

Blackbe;rry

Blackbe;rry Q10 Manuel utilisateur

Blackbe;rry

Blackbe;rry Bold 9900 Manuel utilisateur

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Manuel utilisateur

ISAFE MOBILE

ISAFE MOBILE IS655.2 Manuel utilisateur

Blackbe;rry

Blackbe;rry CURVE 8300 - SMARTPHONE Manuel utilisateur

Blackbe;rry

Blackbe;rry 8707 - VERSION 4.1 Manuel utilisateur