Leviton Opt-X 1000i Manuel utilisateur

Instructions for Use - Opt-X®1000i Enclosure

Leviton Network Solutions, a division of Leviton Mfg. Co., Inc.

Tech Support: 1.800.824.3005 E-mail: appeng@leviton.com Web: www.leviton.com

MTP®is a registered trademark of US Conec, Ltd.

Page 1 of 8

PK-93777-10-02-0C

5R1UM-F03, 5R1UM-S03, 5R2UM-F06,

5R2UM-S06, 5R3UM-F09, 5R3UM-F12,

5R4UM-F12, 5R4UM-F15

5R1UM-*03

5R2UM-*06 5R3UM-F**

5R4UM-F**

FIBER CONNECTOR SAFETY WARNINGS

SAFETY INFORMATION

• Always wear safety glasses.

• Isopropylalcoholisammableandmaycauseeyeirritation.Incaseofcontactwitheyes,ushwithwaterforatleast

15 minutes. When using isopropyl alcohol, always assure proper levels of ventilation. In case of ingestion, consult a

physician immediately.

• Never look directly into a laser light source, point source at a person’s eyes, or point sourceatreectivesurfaces.

• Whenworkingonaberlink,alwaysturnlasersourceoff,ordisconnectcompletely.

• Alwaysdisposeofberdebrisproperly,preferablyusingstickytabs.

• Do not place food or beverages in the vicinity of the work area.

• Thoroughlywashfaceandhandsafterterminatingber.

• Carefullyremoveanyberdebristhatmayhavebeenstucktoclothing,orleftinworkarea, and

dispose of properly.

TIPS AND RECOMMENDATIONS

• Usingisopropylalcohol,thoroughlycleanexposedberandbufferensuringbotharefreefrom dust, oil,

and debris.

• Do not lay ferrule dust covers on a dirty or dusty surface.

• Alwaysusepropertoolsand/oraccessoriestoterminatebersandcleanconnectortips.

QUICK START GUIDE

The following instructions will help you quickly install your Leviton Opt-X®1000i Enclosure for use in your equipment

cabinet or rack. For detailed information on each step, go to the page number listed below.

Safety and Installation Instructions Pg. 2

Quick Start Guide Pg. 2

Equipment Overview Pg. 3

Standard Accessories Pg. 4

Optional Part Numbers Pg. 4

Side View Pg. 4

Cover Removal, and Installation Pg. 5

Cable Installation - Preparation Pg. 5

Opt-X®1000i Fiber Management Ring Pg. 6

Opt-X®1000i Labeling Pg. 7

Cable Installation - Applications Pg. 8

Page 2 of 8 PK-93777-10-02-0C

Page 3 of 8

PK-93777-10-02-0C

1. Removable Covers

2. Removable Cable Grommet

3. Bend Radius Adapter

4. Adjustable Mounting Ears

1. Hook & Loop Lacing Points (For Splice Trays)

2. Cable Lace Points

3. Splice Tray Alignment Pin

4. 1/4 Fiber Cable Management Ring

5. Bulkhead Brackets (Opt-X®= Black, LGX = Gray)

6. Patch Cord Cable Managment Rings

7. Lock (optional)

8. Connector Removal Access Points

9. Ground Lug Mounting Hole

EQUIPMENT OVERVIEW - FIXED & SLIDING TRAY

INTERIOR

NOTE: Covers removed for clarity.

Fixed With Sliding Tray

EXTERIOR

Fixed With Sliding Tray

1. Removable Covers

2. Removable Cable Grommet

3. Bend Radius Adapter

4. Slide Out Termination Tray

5. Adjustable Mounting Ears

1. Hook & Loop Lacing Points (For Splice Trays)

2. Cable Lace Points

3. Splice Tray Alignment Pin

4. 1/4 Fiber Cable Management Ring

5. Bulkhead Brackets (Opt-X®= Black, LGX = Gray)

6. Patch Cord Cable Managment Rings

7. Lock (optional)

8. Connector Removal Access Points

9. Rear Tray Plunger (lift plunger to slide tray backward)

10.Front Tray Plunger (lift plunger to slide tray forward)

11.Ground Lug Mounting Hole

10.

4. 5.

11.

Page 4 of 8

PK-93777-10-02-0C

STANDARD ACCESSORIES (Included with Opt-X®1000i Enclosure)

Prior to installing your Leviton Opt-X®1000i Enclosure, please refer to the table below. This will help ensure that

you have all the items shipped with the unit, and/or any additional items that may be required for proper installation.

Description Image Quantity in

1RU Kit

Quantity in

2RU Kit

Quantity in

3RU Kit

Quantity in

4RU Kit

Self Adhesive Label 2 2 2 2

Spiral Loop, 18" 1 1 0 0

Cable Tie 4 4 6 6

Rack Mount Screw 4 4 4 4

Ground Lug 1 1 1 1

OPTIONAL PART NUMBERS

Description Part Number

Universal Opt-X® Clamp Kit for Enclosure Mounting 5RCMP-KIT

Universal Opt-X® Clamp Kit for Rack Mounting 5RCMR-KIT

Fiber Cable Management 1/4 Ring Kit (bag of four 1/4 rings) 5R100-14R

Splice Tray Mounting Hardware Kit SPLMT-HKT

1RU Mounting Ear for 23" Rack 5R1RU-023

Lock & Key 5L000-LOK

SIDE VIEW (1RU Shown)

1. Adjustable 19" rack mount brackets

2. Cable Clamp kit mounting points

3. Cut grommet as needed to accomodate cables.

NOTE: 2RU and 4RU brackets are reversible for mounting onto 23" racks. Optional 23" RM kit also available for 1RU.

See Optional Part Number list above.

2. 2. 3.

Page 5 of 8

PK-93777-10-02-0C

To open the door: Lift tabs as shown

To remove cover: Push tabs down, and

then slide the cover out.

COVER REMOVAL DOOR LATCH

CABLE INSTALLATION - PREPARATION (SLIDING TRAY)

Multi-Strand

Secure to Enclosure

Secure to Tray

Top View: Tray to Front

NOTE: Tray in forward position, covers

and center bar removed for clarity.

NOTE:

• Routecabletotraythroughgrommetontheopposite

side of cable entry.

• Planforcableroutingpriortotermination.

• Adjustberringkitbasedondesiredapplication(see

page 6 for detail).

• Assurecableslackfortraymovement.

• Foradditionalcableslackmanagement,useoptional

Fiber Management Ring Kit (5R100-14R).

To remove tray from enclosure, lift rear tray plunger, slide tray

fully rearward.

Pictured:Removabletraytofacilitateeld

termination and splicing

NOTE: Grounding lug can be used to secure

cable to enclosure.

Caution:

If grommet needs to

be cut, cut at an angle

towards the center

and on the inside of

the grommet only.

NOTE: Cutting beyond the pre-determined cutting

guides or through the grommet edge may cause

deformation of the grommet and decreased retention

capability.

CABLE GROMMET

Page 6 of 8 PK-93777-10-02-0C

Opt-X®1/4 FIBER CABLE MANAGEMENT RING (Removal, Installation and Assembly)

Opt-X® Fiber management ¼ rings are pre-installed at the factory. To remove, grip the ¼ ring, lift the Position-

Locking Tab, turn counter clockwise until unlocked, and then lift to remove. When removing a half or full

management ring group, simultaneously lift the 2 or 4 Position-Locking Tabs, turn counter clockwise until unlocked,

and then lift to remove.

RING STACKING

Position initial ring unit (¼, ½, or full) upside

downonaatsurface.Positionadditional

ring upside down above initial ring and

presstogetherusingsufcientforceto

engage stack locking device.

CAUTION – always perform stacking

before installing ring unit into tray.

HALF RING ASSEMBLY

Hold a ¼ ring unit in each hand, bring the units

together and engage by placing the tab of the left

unit into the slot of the right unit.

HALF RING INSTALLATION Position ½ ring unit

overouterringslotssothealignmenttabstinto

slots. Press down and turn the ½ ring unit clock-

wise to engage tabs and lock into position.

CAUTION – when installing into a tray that is in the

enclosure, provide adequate support under the tray

by placing a hand under the ring slot area.

FULL RING ASSEMBLY

Hold a ½ ring unit in each hand, bring units together

with tabs above slots, rotate to engage tabs.

FULL RING INSTALLATION Position full ring unit

overinnerandouterringslotssoalignmenttabst

into slots. Firmly press down and turn the full ring

unit clockwise to engage tabs and lock into position.

CAUTION – when installing into a tray that is in the

enclosure, provide adequate support under the tray

by placing a hand under the ring slot area.

HALF RING ASSEMBLY FULL RING ASSEMBLY RING STACKING

Tab

Stacking/Locking

Device (Upper)

Stacking/Locking

Device (Lower)

Slot

RING OVERVIEW RING SIDE PROFILE RING ALIGNMENT SLOTS

Position-Locking Tab

Turn

Push

Opt-X®1000i LABELING (forfront&rearidenticationonenclosure)

Label Printing Organization by Fiber Adapter Type

Horizontal Orientation

Adapter No. of Ports Number Scheme

Duplex SC

(3 pack) 6 1 2 3 4 5 6

Duplex SC

(6 pack) 12

3-4 7-8 11-12

1-2 5-6 9-10

Duplex LC

(6 pack) 12

2 4 6 8 10 12

1 3 5 7 9 11

Quad LC

(6 pack) 24

5-6 / 7-8 13-14 / 15-16 21-22 / 23-24

1-2 / 3-4 9-10 / 11-12 17-18 / 19-20

ST/FC (6 pack) 6 1 2 3 4 5 6

ST/FC (8 pack) 8 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8

Label Printing Organization by Fiber Adapter Type

Vertical Orientation

Adapter Duplex SC

(3 pack)

Duplex SC

(6 pack)

Duplex LC

(6 pack)

Quad LC

(6 pack)

ST/FC

(6 pack)

ST/FC

(8 pack)

No. of

Ports 6 12 12 24 6 8

Number Scheme

1-2 3-4

1-2

3-4

5-6

7-8

2 3-4 2

5-6 7-8

5-6

9-10

11-12

13-14

15-16

4 7-8 4

9-10 11-12

9-10 17-18

19-20

21-22

23-24

6 11-12 6

Page 7 of 8

PK-93777-10-02-0C

5R1UM-F03, 5R1UM-S03

5R3UM-F09

5R3UM-F12, 5R4UM-F12

5R2UM-F06, 5R2UM-S06

Horizontal orientation

•Use3/8”or3/4"labeltape,

depending on adapter plate

•Totallabellength=4"

•Panelsectionis3/4"Hx4"L

Vertical orientation

•Use3/8”or3/4"labeltape, 

depending on adapter plate

•Totallabellength=23/4"

•Panelsectionis3/4"Wx23/4"H

5R4UM-F15

NOTE: Ensure that the label surface area is clean of dirt, oil,

and debris. Recommend use of isopropyl alcohol or a simple

soap and water solution when wiping down surface area.

UNIVERSAL LABELING DEVICES

CABLE INSTALLATION - APPLICATIONS (Typicalinstallations-notspecictoenclosure)

Utilizing MTP® Cassettes

Utilizing Splice Trays Utilizing Fan-Out Kits

Utilizing Pre-Terminated Cables or Field

Termination of tight-buffered cable

Page 8 of 8

PK-93777-10-02-0C

Table des matières

Autres manuels Leviton Enceinte

Leviton

Leviton 5R1UH-S08 Manuel utilisateur

Leviton

Leviton LP3-MC Series Manuel utilisateur

Leviton

Leviton Opt-X 5WMED-04C Manuel utilisateur

Leviton

Leviton Opt-X 500i Manuel utilisateur

Leviton

Leviton 5R4UD-S48 Manuel utilisateur

Leviton

Leviton LP8 Series Manuel utilisateur

Leviton

Leviton Opt-X 5R1UD-S08 Manuel utilisateur

Leviton

Leviton 5R1UM-S08 Manuel utilisateur

Leviton

Leviton LP8 Series Manuel utilisateur

Leviton

Leviton Wetguard COVER-S Manuel utilisateur

Leviton

Leviton Opt-X 5WMNT-01C Manuel utilisateur

Leviton

Leviton Opt-X Ultra 5R1UH-S03 Manuel utilisateur

Leviton

Leviton 17A00 Manuel utilisateur

Leviton

Leviton Opt-X 5WMNT-1C Manuel utilisateur

Leviton

Leviton 49605-14P Manuel utilisateur

Leviton

Leviton 47617-REB Manuel utilisateur

Leviton

Leviton LP 3B Series Manuel utilisateur

Leviton

Leviton Rhino-hide 15 Series Manuel utilisateur

Leviton

Leviton Opt-X 5WSML-02C Manuel utilisateur

Leviton

Leviton 5R1UD-S12 Manuel utilisateur

Leviton

Leviton LP2 Series Manuel utilisateur

Manuels Enceinte populaires d'autres marques

SilentiumPC

SilentiumPC Armis AR5 Manuel

Pulsar

Pulsar 17/TRP80/DSPR Manuel utilisateur

Thermaltake

Thermaltake V150 TG Manuel utilisateur

MSI

MSI MPG SEKIRA 500X Manuel utilisateur

Antec

Antec Dark fleet DF-10 Manuel utilisateur

Nexans

Nexans WTC05 Manuel utilisateur

Peavey

Peavey DS 1502 Manuel utilisateur

D-Link

D-Link ShareCenter Pro DNS-1550-04 Manuel utilisateur

Rosewill

Rosewill RX82-U(JBOD) Manuel utilisateur

QNAP

QNAP SAS JBOD CLI 1.0 Manuel utilisateur

GAMDIAS

GAMDIAS Talos P1 Manuel utilisateur

Auvs

Auvs KR615 Manuel utilisateur

Digitus

Digitus DA-71114 Manuel utilisateur

CommScope

CommScope FDH 3000 Manuel utilisateur

FS FHD-FWME4 Manuel utilisateur

JBL

JBL CS1215T Manuel utilisateur

Pulsar

Pulsar ARAD-S4 Manuel utilisateur

Pulsar

Pulsar AWO454 Manuel utilisateur