Lenovo ThinkSystem DM240N Manuel utilisateur

Hot-add a shelf - DM240N shelves

(support for DG5000 and DG7000)

DM240N

First Edition (July 2023)

LIMIT D AND R STRICT D RIGHTS NOTIC : If data or software is delivered pursuant to a General Services

Administration (GSA) contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-

05925.

Contents

1. Hot-add a shelf - DM240N shelves 1

1.1. Requirements for a hot-add . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê1

1.2. Considerations for a hot-add . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê1

1.3. Prepare for a hot-add. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê2

1.3.1. Prepare non-dedicated RoCE-capable ports for a hot-add. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê2

1.3.2. Prepare a DM7100F or DG7000 HA pair to hot-add a second shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê4

1.3.3. Prepare to manually assign drive ownership for a hot-add . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê5

1.4. Install a drive shelf for a hot-add . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê6

1.5. Cable a drive shelf for a hot-add . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê8

1.5.1. Considerations when cabling for a hot-add . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê8

1.5.2. Cable a hot-add shelf for a DM5100F or DG5000 HA pair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê8

1.5.3. Cable a hot-add shelf for a DM7100F HA pair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê10

1.5.4. Cable a hot-add shelf for a DG7000 HA pair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê12

1.6. Complete the hot-add . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê14

2. Appendix 16

2.1. Contacting support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê16

2.2. Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê16

2.3. Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê17

Chapter 1. Hot-add a shelf - DM240N shelves

You can hot-add a DM240N drive shelf after your HA pair meets certain

requirements, and after the preparation tasks applicable to your HA pair are

completed.

1.1. Requirements for a hot-add

Your HA pair must meet certain requirements before hot-adding a DM240N drive shelf.

•Your system and version of ONTAP must support the DM240N shelf and drives you are hot-

adding.

•You must have the correct number and type of cables to connect the shelf.

•Your HA pair must have enough available RoCE-capable ports to support the number of

shelves you are hot-adding.

For each shelf you are hot-adding, you need a minimum of two RoCE capable ports on each

controller. These ports can be on board the controllers, on RoCE-capable PCIe cards, a

combination of both, or on RoCE-capable I/O modules, as supported by your system.

If your HA pair does not have enough available RoCE-capable ports, and your system supports

the use of RoCE-capable PCIe cards or I/O modules, you must have installed the additional

cards or I/O modules into the correct controller slots, as supported by your system.



Non-dedicated RoCE-capable ports must be configured for storage use (not

networking use).

Prepare non-dedicated RoCE-capable ports for a hot-add

•Your HA pair must have less than the maximum number of shelves supported, by at least the

number of shelves you plan to hot-add.

You cannot have exceeded the maximum number of shelves supported by your HA pair after

hot-adding shelves.

•If you are hot-adding a shelf to an HA pair that already has a DM240N shelf, your HA pair

cannot have any storage cabling error messages, and it must be cabled as multipath HA.

•To change the DM240N shelf ID, you can use a paper clip or ballpoint pen to access the shelf

ID button behind the Operator Display Panel (ODP).

1.2. Considerations for a hot-add

You should familiarize yourself with best practices and aspects about this procedure before hot-

adding a DM240N drive shelf.

•Best practice: The best practice is to have the current version of ONTAP software installed

before hot-adding a shelf.

Having the most current version of ONTAP software also will install the latest Disk Qualification

Package (DQP) and NVMe shelf module (NSM) firmware. The DQP allows your system to

recognize and use newly qualified drives. This avoids system event messages about having

noncurrent drive information and prevention of drive partitioning because drives are not

recognized. The DQP also notifies you of noncurrent drive firmware.

Do not revert firmware to a version that does not support your shelf and its

components.

•After you have cabled a hot-added shelf, ONTAP recognizes the shelf:

◦Drive ownership is assigned if automatic drive assignment is enabled.

◦NSM shelf firmware and drive firmware should be updated automatically, if needed.

Firmware updates can take up to 30 minutes.

1.3. Prepare for a hot-add

You must complete the preparation tasks applicable to your HA pair before hot-adding a DM240N

drive shelf.

1.3.1. Prepare non-dedicated RoCE-capable ports for a hot-add

If your HA pair has non-dedicated RoCE-capable ports that you are using to hot-add a DM240N

drive shelf, you must make sure the ports are configured for storage use (not networking use).

Depending on your system, the RoCE-capable ports are on board the controllers, on RoCE-capable

PCIe cards, a combination of both, or on RoCE-capable I/O modules.

Before you begin

You must have met the system requirements.

Requirements for a hot-add

About this task

•For some systems, when a RoCE-capable PCIe card or I/O module is installed in a supported

slot on a controller, the ports automatically default to storage use (instead of networking);

however, it is recommended that you complete this procedure to verify the RoCE-capable ports

are configured for storage use.

•If you determine that the non-dedicated RoCE-capable ports in your HA pair are not configured

for storage use, it is a nondisruptive procedure to configure them.

If your HA pair is running a version of ONTAP 9.6, you need to reboot the

controllers, one at a time.

If your HA pair is running ONTAP 9.7 or later, you do not need to reboot the

controllers, unless one or both controllers are in maintenance mode. This

procedure assumes that neither controller is in maintenance mode.

Steps

1. Verify if the non-dedicated ports in the HA pair are configured for storage use: storage port

show

You can enter the command on either controller module.

If your HA pair is running ONTAP 9.8 or later, the non-dedicated ports display storage in the

Mode column.

If your HA pair is running ONTAP 9.7 or 9.6, the non-dedicated ports, which display false in the

Is Dedicated? column, also display enabled in the State column.

2. If the non-dedicated ports are configured for storage use, you are done with this procedure.

Otherwise, you need to configure the ports by completing steps 3 through 6.



When non-dedicated ports are not configured for storage use, the command

output displays the following:

If your HA pair is running ONTAP 9.8 or later, the non-dedicated ports display

network in the Mode column.

If your HA pair is running ONTAP 9.7 or 9.6, the non-dedicated ports, which

display false in the Is Dedicated?` column, also display disabled in the

State column.

3. Configure the non-dedicated ports for storage use, on one of the controller modules:

You must repeat the applicable command for each port you are configuring.

If your HA pair is

running…

Then…

ONTAP 9.8 or later storage port modify -node node name -port port name -mode

storage

ONTAP 9.7 or 9.6 storage port enable -node node name -port port name

4. If your HA pair is running ONTAP 9.6, reboot the controller module so that the port changes

take effect: system node reboot -node node name -reason reason for the reboot

Otherwise, go to the next step.

The reboot can take up to 15 minutes.

5. Repeat steps for the second controller module:

If your HA pair is

running…

Then…

ONTAP 9.7 or later a. Repeat step 3.

b. Go to step 6.

ONTAP 9.6 a. Repeat steps 3 and 4.

The first controller must have already completed

its reboot.

b. Go to step 6.

6. Verify that the non-dedicated ports on both controller modules are configured for storage use:

storage port show

You can enter the command on either controller module.

If your HA pair is running ONTAP 9.8 or later, the non-dedicated ports display storage in the

Mode column.

If your HA pair is running ONTAP 9.7 or 9.6, the non-dedicated ports, which display false in the

Is Dedicated? column, also display enabled in the State column.

1.3.2. Prepare a DM7100F or DG7000 HA pair to hot-add a second shelf

If you have a DM7100F or DG7000 HA pair with one DM240N drive shelf that is cabled to one set of

RoCE-capable ports on each controller, you must recable the shelf (after you have installed the

additional RoCE-capable PCIe cards or I/O modules) across both sets of ports on each controller,

before hot-adding the second shelf.

Before you begin

•You must have met the system requirements.

Requirements for a hot-add

•You must have enabled the ports on the RoCE-capable PCIe cards or I/O modules you

installed.

Prepare non-dedicated RoCE-capable ports for a hot-add

About this task

•Recabling port connections is a nondisruptive procedure when your shelf has multipath-HA

connectivity.

You recable the first shelf across both sets of ports on each controller so that when you hot-

add the second shelf, both shelves have more resilient connectivity.

•You move one cable at a time to maintain connectivity to the shelf at all times during this

procedure.

Steps

1. Recable the existing shelf’s connections across both sets of ports on each controller, as

applicable to your system.

Moving a cable does not require any wait time between unplugging the cable

from one port and plugging it into another port.

If you have an… Then…

DM7100F HA pair



If needed, you can reference cabling illustrations

showing an existing single shelf and the recabled

shelf, in a two shelf configuration.

Cable a hot-add shelf for a DM7100F HA pair

a. On controller A, move the cable from port e0d to slot 5 Port b

(e5b).

b. Repeat the same cable move on controller B.

DG7000 HA pair



If needed, you can reference cabling illustrations

showing an existing single shelf and the recabled

shelf, in a two shelf configuration.

Cable a hot-add shelf for a DG7000 HA pair

a. On controller A, move the cable from slot 4 port a (e4a) to slot 5

port b (e5b).

b. Repeat the same cable move on controller B.

2. Verify that the recabled shelf is cabled correctly.

1.3.3. Prepare to manually assign drive ownership for a hot-add

If you are manually assigning drive ownership for the DM240N drive shelf you are hot-adding, then

you need to disable automatic drive assignment if it is enabled.

Before you begin

You must have met the system requirements.

Requirements for a hot-add

About this task

You need to manually assign drive ownership if drives in the shelf will be owned by both controller

modules in the HA pair.

Steps

1. Verify whether automatic drive assignment is enabled: storage disk option show

You can enter the command on either controller module.

If automatic drive assignment is enabled, the output shows on in the Auto Assign column (for

each controller module).

2. If automatic drive assignment is enabled, disable it: storage disk option modify -node

node_name -autoassign off

You must disable automatic drive assignment on both controller modules.

1.4. Install a drive shelf for a hot-add

Installing a new DM240N drive shelf involves installing the shelf into a rack or cabinet, connecting

the power cords (which automatically powers on the shelf), and then setting the shelf ID.

Before you begin

•You must have met the system requirements.

Requirements for a hot-add

•You must have completed the applicable preparation procedures.

Prepare for a hot-add

Steps

1. Install the rail-mount kit that came with your shelf by using the installation flyer that came in the

kit box.

Do not flange-mount the shelf.

2. Install and secure the shelf onto the support brackets and rack or cabinet by using the

installation flyer.



A fully loaded DM240N shelf can weigh up to 66.78 lbs (30.29 kg) and

requires two people to lift or use of a hydraulic lift. Avoid removing shelf

components (from the front or rear of the shelf) to reduce the shelf weight,

because shelf weight will become unbalanced.

3. Connect the power cords to the shelf, secure them in place with the power cord retainer if they

are AC power supplies, or the two thumb screws if they are DC power supplies, and then

connect the power cords to different power sources for resiliency.

A shelf powers up when connected to a power source; it does not have power switches. When

functioning correctly, a power supply’s bicolored LED illuminates green.

4. Set the shelf ID to a number that is unique within the HA pair:

More detailed instructions are available:

Change a shelf ID - DM240N shelves

a. Remove the left end cap and locate the small hole to the right of the LEDs.

b. Insert the end of a paper clip or similar tool into the small hole to reach the shelf ID button.

c. Press and hold the button (for up to 15 seconds) until the first number on the digital display

blinks, and then release the button.

If the ID takes longer than 15 seconds to blink, press and hold the button

again, making sure to press it in all the way.

d. Press and release the button to advance the number until you reach the desired number

from 0 to 9.

e. Repeat substeps 4c and 4d to set the second number of the shelf ID.

It can take up to three seconds (instead of 15 seconds) for the number to blink.

f. Press and hold the button until the second number stops blinking.

After about five seconds, both numbers start blinking and the amber LED on the ODP

illuminates.

g. Power-cycle the shelf to make the shelf ID take effect.

You must unplug both power cords from the shelf, wait 10 seconds, and then plug them

back in.

When power is restored to the power supplies, their bicolored LEDs illuminate green.

Autres manuels pour ThinkSystem DM240N

Table des matières

Autres manuels Lenovo Serveur

Lenovo

Lenovo Neptune DWC RM100 Manuel d'utilisation

Lenovo

Lenovo ThinkServer RD210 Manuel

Lenovo

Lenovo ThinkSERVER TS130 Manuel utilisateur

Lenovo

Lenovo ThinkServer TD200x Mode d’emploi

Lenovo

Lenovo ThinkServer RD210 Feuille d'instructions

Lenovo

Lenovo System x3250 M5 Manuel utilisateur

Lenovo

Lenovo 7Z59 Manuel utilisateur

Lenovo

Lenovo ThinkSystem ST250 V3 Manuel utilisateur

Lenovo

Lenovo ThinkServer TS140 Manuel utilisateur

Lenovo

Lenovo ThinkServer RD210 Manuel utilisateur

Lenovo

Lenovo ThinkServer TD100 Manuel utilisateur

Lenovo

Lenovo ThinkServer RD530 Manuel de la liste des pièces

Lenovo

Lenovo ThinkServer TD200x Mode d’emploi

Lenovo

Lenovo ThinkServer TD230 Manuel utilisateur

Lenovo

Lenovo ThinkServer TS200v Manuel utilisateur

Lenovo

Lenovo ThinkServer TS200 Manuel utilisateur

Lenovo

Lenovo IdeaCentre D400 Manuel

Lenovo

Lenovo ThinkSystem HR350A Manuel du propriétaire

Lenovo

Lenovo ThinkServer RD330 Manuel utilisateur

Lenovo

Lenovo System x3850 X6 Instructions d'installation et d'entretien

Lenovo

Lenovo ThinkServer RD430 Manuel utilisateur

Lenovo

Lenovo ThinkSystem ST550 7X09 Manuel utilisateur

Lenovo

Lenovo THINKSERVER RS210 Manuel de service

Lenovo

Lenovo THINKSERVER RS210 Feuille d'instructions

Manuels Serveur populaires d'autres marques

HP AlphaServer ES47 Manuel utilisateur

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur