Lenovo ThinkSystem 440-16i Manuel utilisateur

ThinkSystem 440-16i SAS/SATA PCIe Gen4

12Gb Internal HBA Installation and User

Guide

First Edition (May 2020)

LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant to a General Services

Administration (GSA) contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-

05925

Table of Contents

Chapter 1: Overview ...........................................................................................................................1

1.1 Operating System Support................................................................................................................................. 1

1.2 PCIe Host Interface ............................................................................................................................................. 1

1.3 LED Management ................................................................................................................................................ 2

1.4 Storage Interface Features................................................................................................................................. 2

1.5 Adapter Characteristics...................................................................................................................................... 3

Chapter 2: Adapter Installation Instructions ....................................................................................4

Chapter 3: Safety Characteristics .....................................................................................................6

Guide

Chapter 1: Overview

The ThinkSystem 440-16i SAS/SATA PCIe Gen4 12Gb internal HBA, based on the SAS3816 controller, is a high-

performance PCIe-to-SATA/SAS storage adapter. The SerDes technology enables operation of SAS and SATA storage

devices in a single drive bay. A single controller can operate in all two modes concurrently: SAS and SATA. The adapter

negotiates between the speeds and the protocols to recognize and concurrently interface with these two storage device

types:

SAS data transfer rates of 12Gb/s, 6Gb/s, and 3Gb/s per phy

SATA transfer rates at 6Gb/s and 3Gb/s per phy

The following table summarizes key adapter features.

Table 1 Adapter Features

Adapt

40-16i

Ports

16 internal

I/O Processor

SAS3816

Form Factor

Custom

Storage Interface Connectors

Four SFF-8654 x4

Host Interface

SFF-8654 x8

Storage Interface

SAS and SATA

1.1 Operating System Support

The adapter supports the operating systems in the following list.

Microsoft Windows

VMware vSphere/ESXi

Red Hat Enterprise Linux

SuSE Linux

Ubuntu Linux

Citrix XenServer

CentOS Linux

Debian Linux

Oracle Enterprise Linux

Fedora

FreeBSD

Visit http://support.lenovo.com, and download the latest firmware and driver for the adapter.

1.2 PCIe Host Interface

The adapter’s PCIe 4.0 host interface provides maximum transmission and reception rates of up to 128 GT/s (16 Gb/s per

lane). The controller uses a packet-based communication protocol to communicate over the serial interconnect. Other

PCIe host interface features include the following:

Eight-lane PCIe host interface

Guide

PCIe Hot Plug

Power management

– Supports the PCI Bus Power Management Interface Specification Revision 1.2

– Supports Active State Power Management, including the L0 states, by placing links in a power-saving mode

during times of no link activity

Error handling

High bandwidth per pin with low overhead and low latency

Lane reversal and polarity inversion

Single-phy (one-lane) link transfer rate of 16 GT/s, 8 GT/s, 5 GT/s, and 2.5 GT/s in each direction

Eight-lane aggregate bandwidth of up to 16 GB/s (16,000 MB/s)

Support of x8, x4, x2, and x1 link widths

1.3 LED Management

The adapter offers LED management support for SAS/SATA backplane.

1.4 Storage Interface Features

The adapter’s storage interface supports concurrent operation with SAS and SATAdevices to provide a fully functional

solution for any storage environment.

SAS features:

– SAS data transfers at 12Gb/s, 6Gb/s, and 3Gb/s

– DataBolt technology on all SAS phys to improve performance

– Serial, point-to-point, enterprise-level storage interface

– Wide ports that contain multiple phys

– Narrow ports that contain a single phy

– SAS phy power management

– Data transfer by using SCSI information units

– T10 data protection management

– Support for persistent connection capability

– Support for SPL-3 initiate close capability

– Configurable Rx and Tx polarity inversion

– Configurable phy-to-disk mapping

– Configurable SSC

SATA interface features:

– SATA and STP data transfers at 6Gb/s and 3Gb/s

– Addressing of multiple SATA targets through an expander

Guide

1.5 Adapter Characteristics

The adapter is a 6.02 in. × 2.67 in. (153 mm × 67.7 mm) board. The following figure shows the connectors and LED

locations on the adapter.

Figure 1 Card Layout for the Thinksystem 440-16i SAS/SATA PCIe Gen4 12Gb Internal HBA

The following table describes the headers and connectors on the adapter.

Table 2 Headers and Connectors

Con

nector

ription

andard edge card connector

he interface between the storage adapter and the host system.

Default serial boot ROM (SBR)

2-pin connector. Reserved.

n-board serial UART connector

-pin connector. Reserved.

(C3), J6 (C2),

7(C1), J18

(C0)

orage interface connectors

Four

SFF-8654 4-port internal connectors.

nnect the adapter by cable to the storage devices.

J25

Power

Power connector.

The following table describes the LEDs on the adapter.

Table 3 LED Designations

LED

ription

LED 2

ellow controller over temperature

Stays

on solid to indicate that the SAS3816 device temperature sensor is over the

temperature threshold. When the device is in the proper temperature range, this LED is off.

LED 3

Green system heartbeat

Indicates that the SAS3816 IoC ASIC is operating normally. This LED blinks at 1 Hz.

J17 (C1)

J18 (C0)

LED3

LED2

J5 (C3)

J6 (C2)

J25

Guide

Chapter 2: Adapter Installation Instructions

1. Unpack the adapter and inspect the adapter for damage.

Unpack the adapter in a static-free environment. Remove the adapter from the antistatic bag, and carefully inspect the

adapter for damage. If you notice any damage, contact Lenovo or your reseller support representative.

ATTENTION To avoid the risk of data loss, back up your data before you change your system configuration.

2. Review the adapter connectors.

3. Check whether the adapter is well-fixed on the mounting bracket.

The adapter ships preinstalled on a mounting bracket. Check that the adapter is fixed in place. If any loose screws

exist, tighten the screws using a No.1 Phillips torque screwdriver. The maximum torque is 4.8 ± 0.5 inch-pounds.

ATTENTION Exceeding this torque specification can damage the board, connectors, or screws, and can void

the warranty on the board. Damage caused to the board as a result of changing the bracket can

void the warranty on the board. Adapters returned without a bracket mounted on the board will be

returned without return merchandise authorization (RMA) processing.

4. Prepare the server.

Turn off the power to the server and disconnect all power cords.

5. Remove the top cover from the chassis.

6. Remove any components that might impede the adapter installation.

Refer to ThinkSystem Server Documentation Center, select your product, and review the Hardware replacement

procedures section for detailed instructions.

7. Install the adapter.

Align the notches on the mounting bracket with the four pins or three pins on the chassis, place down the adapter, and

slightly slide the adapter to secure it in place, as the following figure shows.

ATTENTION The shape, size, and locations of the components on your adapter and its bracket might vary

from the following illustration.

Figure 2 Installing the Adapter

Guide

8. Connect any cables to the adapter.

Refer to ThinkSystem Server Documentation Center, select your product, and review the internal cable routing section

for detailed instructions.

9. Reinstall any parts that have been previously removed and connect any internal cables.

Refer to ThinkSystem Server Documentation Center, select your product, and review the Hardware replacement

procedures section and the Internal cable routing section for detailed instructions.

10. Reinstall the top cover on the chassis.

Refer to ThinkSystem Server Documentation Center, select your product, and review the Hardware replacement

procedures for detailed instructions.

11. Reconnect any external cables and turn on the power to the system.

The hardware installation of your adapter is complete.

Guide

Chapter 3: Safety Characteristics

The adapter meets or exceeds the requirements of UL flammability rating 94 V0. Each bare board is also marked with the

supplier name or trademark, type, and UL flammability rating. For the boards installed in a PCIe bus slot, all voltages are

lower than the SELV 42.4 V limit.

Guide

Trademarks

LENOVO, LENOVO logo, and THINKSYSTEM are trademarks of Lenovo. All other trademarks are the property of their

Table des matières

Autres manuels Lenovo Adaptateur

Lenovo

Lenovo CH580 Manuel utilisateur

Lenovo

Lenovo ThinkSystem 1610-4P Manuel utilisateur

Lenovo

Lenovo ThinkPad WMTB-177N Manuel utilisateur

Lenovo

Lenovo 02K6699 Manuel utilisateur

Lenovo

Lenovo CH560 Manuel utilisateur

Lenovo

Lenovo QLogic 8Gb FC Single-port Manuel utilisateur

Lenovo

Lenovo 43N3412 Manuel utilisateur

Lenovo

Lenovo ThinkSystem RAID 940-16i Manuel utilisateur

Lenovo

Lenovo ThinkSystem RAID 930-16i Manuel utilisateur

Lenovo

Lenovo Flex System IB6132 Manuel utilisateur

Lenovo

Lenovo NETWORK CARD - WIRELESS ADAPTER MW600-B-LO Manuel utilisateur

Lenovo

Lenovo N2226 Manuel utilisateur

Lenovo

Lenovo N2225 Manuel utilisateur

Lenovo

Lenovo USB 3.0 to DVI/VGA Monitor Adapter Manuel utilisateur

Lenovo

Lenovo ThinkPad Series Manuel utilisateur

Lenovo

Lenovo 90W AC/DC Manuel utilisateur

Lenovo

Lenovo AL601 Manuel utilisateur

Lenovo

Lenovo 45K5296 Manuel utilisateur

Lenovo

Lenovo ThinkPad 72W Manuel utilisateur

Lenovo

Lenovo 65W USB-C AC Travel Adapter Manuel utilisateur

Lenovo

Lenovo 90W AC Adapter Manuel utilisateur

Lenovo

Lenovo ThinkSystem Intel XXV710-DA2 Manuel utilisateur

Lenovo

Lenovo Intel X520 Manuel utilisateur

Lenovo

Lenovo Brocade 16Gb FC Single-port Manuel utilisateur

Manuels Adaptateur populaires d'autres marques

PCB Piezotronics

PCB Piezotronics 090B274 Manuel utilisateur

Auvidea

Auvidea J20 Manuel du produit

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuel utilisateur

Akribis

Akribis ITF-21-BISS-MIT Manuel utilisateur

Tenda

Tenda W54U Manuel utilisateur

ROHO

ROHO AGILITY Manuel utilisateur

PROLiNK

PROLiNK WN2001 Manuel utilisateur

Hawking

Hawking HUF2 Manuel utilisateur

Airlink101

Airlink101 AWLC4030 Manuel utilisateur

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuel utilisateur

Philips

Philips SWA4554S/10 Manuel utilisateur

JVC

JVC TS-C9D2B Manuel d'instructions

NETGEAR

NETGEAR A6100 Manuel utilisateur

D-Link

D-Link DWA-121 Manuel utilisateur

Philips

Philips SWA2037 Manuel utilisateur

Basalte

Basalte 0610-20 Manuel utilisateur

Yealink

Yealink EHS40 Manuel utilisateur

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuel utilisateur