Leister TAPEMAT Manuel utilisateur

TAPEMAT

Leister Process Technologies

Galileo-Strasse 10

CH-6056 Kaegiswil/Switzerland

Tel. +41 41 662 74 74

Fax +41 41 662 74 16

www.leister.com

sales@leister.com

Leister TAPEMAT

Hot-Air welding machine

TAPEMAT: Manually guided automatic hot-air welding machine for welding PVC straps from 45 mm to max.

50 mm wide – as the reinforcement for tarpaulins – on horizontal and level surfaces.

TAPEMAT Spriegel: : Manually guided automatic hot-air welding machine for welding PVC straps (reinforcement

strips) 100 mm and 125 mm wide – as the reinforcement for tarpaulins – on horizontal and level surfaces.

Application

Please read operating instructions carefully before use

and keep for future reference.

Operating Instructions (Translation of the original operating instructions)

Danger to life if you open the equipment, since this reveals

current-conducting

components and connections.

Remove the mains plug from the plug socket before opening the equipment.

Incorrect use of the hot air tool can present a fire and explosion hazard

especially near combustable materials and explosive gases.

Do not touch the element housing and nozzle when hot as they can cause burns.

Allow the tool to cool down. Do not point the hot air flow at people or animals.

Warning

Connect tool to a receptacle with protective earth terminal. Any interruption of

the protective conductor inside or outside the tool is dangerous!

Use only extension cables/cords with protective conductor!

Conductor cross-section: 4 x 2.5mm2

The tool must be operated under supervision.

Heat can ignite flammable materials which are not in view.

The machine may only be used by qualified specialists or under their supervision.

Children are not authorized to use this machine.

For personal protection, we strongly recommend the tool be connected to an

RCCB (Residual Current Circuit Breaker) before using it on construction sites.

The mains voltage, that is quoted on the equipment must agree with the mains

voltage.

IEC/EN 61000-3-11; Zmax = 0.039

Ω

+ j 0.024

Ω

. If necessary, consultate supply

authority.

You must always use a residual current circuit breaker for protection to

persons when working on building sites.

Protect the tool from damp and wet.

230

400

Caution

The equipment must not be lifted using the additional weight.

TAPEMAT TAPEMAT Spriegel

Voltage V~ 3 ×400 3 ×400

Power consumption kW 10 10

Frequency Hz 50 / 60 50 / 60

Temperature °C ca. 650 ca. 650

Speed m/min. 4 – 20 4 – 20

Noise level LpA (dB) 83 83

Weld seam width max. mm 50 2 × 20

Tape width mm 50 100 / 125

Dimensions L×W×Hmm 555 ×435 ×370 555 ×435 ×370

Weight kg 35 40

without power supply cord

Mark of conformity 22

Approval mark 33

Certification scheme CCA CCA

Protection class I 11

Technical data and specifications are subject to change without prior notice.

Leister Process Technologies, Galileo-Strasse 10, CH-6056 Kaegiswil/Switzerland

confirms that this

product,

in the version as brought into circulation through us, fulfils the requirements

of the following EC directives.

Directives

98/37, 2004/108, 2006/95

Harmonised standards: E

N 12100-1, EN 12100-2, EN 60204-1, EN 55014-1, EN 55014-2,

EN 61000-6-2, EN 61000-3-2, EN 61000-3-11 (Zmax),

EN 50366, EN 62233, EN 60335-2-45

Kaegiswil, 25.08.2008

Bruno von Wyl Christiane Leister

Technical Director Owner

Power tools, accessories and packaging should be sorted for environmental-friendly recycling. Only for EC

countries: Do not dispose of power tools into household waste! According to the European Directive

2002/96/ on waste electrical and electronic equipment and its incorporation into national law, power tools

that are no longer suitable for use must be separately collected and sent for recovery in an environmental-

friendly manner.

Disposal

Conformity

Technical data

Tool description

1. Mains connection cable

2. Cabinet

3. Main switch

4. Release switch

5. Motor On/Off

6. Speed variation knob

7. Temperature variation knob

8. Welding nozzle

9. Hot air blower

10. Equipment holder

11. Transporting wheel

12. Drive roller / Pressure roller

13. Welding nozzle adjustment screw

14. Welding nozzle adjustment nut

15. Welding nozzle adjustment screws

16. Guiding handle, lower section

17. Guiding handle, upper section

18. Clamping lever, guiding handle joint

19. Clamping lever, height adjustment

20. Retainer (for mains connection cable)

21. Guide roller

22. Additional weight

23. Retaining pin

24. Stop ring

25. Diverting roller

26. Separating wall

27. Strap retaining rollers

28. Sensor

29. Stop screw

30. Contact generator

31. Guide trolley

32. Strap unrolling device

33. Tensioning brake disc

34. Locator (strap unrolling device)

35. Threaded pin

13 15

2423

Before putting into operation, check the mains connection cable (1)

and the plug for electrical and mechanical damage.

• Fit the guiding handle (16/17).

• Hook mains connection cable (1) into retainer (20).

•

Adjust the guiding handle to the desired height using the clamping lever (19).

• Insert the strap unrolling device (32) into the locator (34).

• Check the default setting of the welding nozzle (8).

– The welding nozzle (8) must be aligned and set parallel and centrically to

the drive roller/pressure roller (12).

– The distance to the tarpaulin must be approx. 4 mm.

• Carry out the adjustment of the welding nozzle (8):

– Height with adjustment screw (13)

– Vertical with adjustment nut (14)

– Other settings with adjustment screws (15).

• Check the guide roller (21)

– the guide roller (21) must be aligned centrally to the

Drive roller / Pressure roller (12).

Readiness for operation

4 mm

13 15

Adjusting the TAPEMAT welding nozzle

Welding nozzles

Welding nozzle TAPEMAT

50 mm width

Welding nozzle TAPEMAT«Spriegel»

100 mm oder 125 mm width

Trapaulins

Straps 50 mmWeld seam

50 mm

Plane

PVC-Spriegel 100 oder 125 mm

Weld seam

20 mm

Weld seam

20 mm

• Swing the guide roller (21) upwards.

• Move the hot air blower (9) outwards with the guide

trolley (31), swing upwards and position using the

stop ring (24) to the retaining pin (23).

23 21 9

• Check the basic setting of the welding nozzle (8).

– The welding nozzle (8) must be aligned parallel and centrally to the Drive

roller / Pressure roller (12) and set in position.

– Clamp and stretch welding tape.

– Nozzle outlet approx. 0.5 – 1 mm gap to the stretched welding tape

(figure D).

• Carry out the precise adjustment of the welding nozzle (8) as follows:

– Remove strap unrolling device (32) and additional weight (22).

– Tilt the TAPEMAT Tarpaulin Bow (figure A).

– Loosen adjustment screws (15) and push the welding nozzle (8)

upwards parallel to the pressure roller (12), then tighten the adjustment

screws (15) again (figure B).

– Position the outlets of the welding nozzle (8) horizontally with the

adjustment nut (14), symmetrically to the pressure roller (12) (figure C).

– Set the vertical height of the welding nozzle (8) to the welding tape with

the adjustment screw (13) (approx 0.5 – 1 mm gap). The height depends

on the material (figure D).

812

13 15

Adjusting the TAPEMAT Tarpaulin Bow welding nozzle

Figure A Figure B Figure C Figure D

Transport position

• Loosen the hexagon socket screw and adjust the welding tape offset

on the side so that the tape material lies by the side of the diverting

roller (25), then tighten the hexagon socket screw again (figure E).

Adjusting the TAPEMAT Tarpaulin Bow diverting roller

Figure E

Threading the strap

• Remove the strap unrolling device (32) from the locator (34).

• Insert the strap into the strap unrolling device (32) and rotate the tensioning brake disc (33) to the stop (left

hand thread).

• Insert the strap unrolling device (32) into the locator (34).

• Adjusting the tensioning brake disc (33)

– The braking force for the various strap widths is adjusted via the

threaded pin (35) at the tensioning brake disc (33).

–

The position groove at the brass part of the tensioning brake disc (33) is

used as an adjustment aid. The mean braking force for tensioning is

achieved when the position groove is flush with the reference edge.

•Note: When the strap is not welded linear on the tarpaulin, although

the guide roller is led alongside the mark, then the braking force of the tensioning brake disc (33) must be

increased.

• Thread the strap as follows:

– Remove additional weight (22) (Figure 1), lift the unit up and position the additional weight (22) under

the unit (Figure 2).

– Stand on the side opposite the hot air blower (9) (Figure 3).

– Insert the strap into the diverting rollers (25) (Figure 4), pull under the Drive Roller / Pressure

Roller (12) and then insert into the strap retaining rollers (27) (Figure 5). The strap retaining

rollers (27) are adjustable.

– Lift the unit, remove the additional weight (22) and hang back on the TAPEMAT.

35 Reference edge

Position groove

Figure

25 12 27

Before the welding

Connect the equipment to the mains. The mains voltage must agree with the equip-

ment voltage.

• Swing the guide roller (21) downwards.

• Set the welding parameters (see page 9).

welding temperature must be reached (heating time approx. 5 minutes).

During the welding procedure, the operator must always be on the guiding handle side and guide the

welding machine.

• Lower the hot air blower (9) and insert between the tarpaulin and the strap up to the stop.

The drive motor starts automatically by the sensor (28).

If automatic starting does not take place adjust the sensor (see page 10).

The machine can also be started manually using the switch Motor On/Off (5)

(1st push «Motor ON» / 2nd push «Motor OFF»).

• The automatic welding machine is guided by the guide roller (21). Any variations can be corrected by the

guiding handle (17). Do not apply any pressure to the guiding handle (17) since this could cause welding

faults.

• Carry out a welding test in accordance with the welding instructions from the material manufacturer and the

national standards or directives.

• Check the test weld.

2423

17 4

1FI

120

230

Performing a test weld

Welding

After the welding

•Setmain switch (3) to I. Push the release switch (4) (hot air blower running).

• Welding temperature

Set the temperature variation knob (7) to the desired value.

Heating up time approx. 5 minutes.

• Welding speed

– Set the welding speed determined for the particular tarpaulins and straps using the speed variation knob (6).

• Joining force

– The joining force is transmitted to the Drive roller / Pressure roller (12).

– If necessary, the additional weight (22) can be removed.

•Drive out the hot air blower (9) with guide trolley (31), pivot up and lock in position with the stop ring (24)

at retaining pin (23).

•

Set the temperature variation knob (7) to zero; this allows the welding nozzle (8) to cool off (approx. 10 minutes).

• After the welding nozzle (8) has cooled off, set the main switch (3) to 0.

3 7 6

Caution

The machine must not be lifted on the additional weight (22).

The additional weight (22) is not fixed in position.

Bei Netzausfall Heissluftgebläse (9) ausfahren und Hauptschalter (3) auf 0stellen. Ist die Netz-

spannung wieder vorhanden, muss der Hauptschalter (3) auf Igestellt und Taster Freischaltung (4)

gedrückt werden.

Setting the welding parameters

• Fault

– The drive motor does not start automatically when inserting the nozzle.

•Cause

–Sensor (28) set incorrectly.

• Action

Allow the welding nozzle (8) to cool off (approx. 10 minutes).

– Set the main switch (3) to 0.

– Lower hot air blower (9) and move into the welding position up to the stop.

– Release stop screw (29) for sensor (28).

– Slide sensor (28) to contact generator (30) (switching distance 0.5 mm).

– Tighten the stop screw (29) for sensor (28).

– Move the hot air blower (9) out with guide trolley (31), swing up and position with stop ring (24) and

retaining pin (23).

• If the causes of the fault still remain contact the service facility.

Fault – Cause – Action

0.5 mm

Top view

Autres manuels pour TAPEMAT

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Leister Système de soudage

Leister

Leister BITUMAT B2 Manuel utilisateur

Leister

Leister WELDPLAST S1 Manuel utilisateur

Leister

Leister Twinny T Manuel utilisateur

Leister

Leister Astro Manuel utilisateur

Leister

Leister DRIVE Manuel utilisateur

Leister

Leister VARIANT T1 Manuel utilisateur

Leister

Leister Twinny S Manuel utilisateur

Leister

Leister NOVOLAS Basic AT Guide de l'utilisateur

Leister

Leister WELDPLAST S2 Manuel utilisateur

Leister

Leister GEOSTAR G5 LQS Manuel utilisateur

Leister

Leister TWINNY T7 Manuel utilisateur

Leister

Leister WELDPLAST S6 Manuel utilisateur

Leister

Leister WELDPLAST S2 Manuel utilisateur

Leister

Leister VARIMAT V2 Series Manuel utilisateur

Leister

Leister Unifloor E Manuel utilisateur

Leister

Leister TWINNY T7 Guide de configuration

Leister

Leister HEMTEK ST Manuel utilisateur

Leister

Leister Comet 700 Manuel utilisateur

Leister

Leister WELDPLAST S4 Manuel utilisateur

Leister

Leister BITUMAT B2 Manuel utilisateur

Leister

Leister FUSION 1 Manuel utilisateur

Leister

Leister VARIANT T1 Manuel utilisateur

Leister

Leister Uniplan E Manuel utilisateur

Leister

Leister VARIANT T1 Manuel utilisateur

Manuels Système de soudage populaires d'autres marques

Berner

Berner PLASMACUT 54 Manuel utilisateur

Pro Spot

Pro Spot PR-155 Manuel utilisateur

Forney

Forney 210 Manuel utilisateur

Thermal Arc

Thermal Arc 400S Manuel utilisateur

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuel utilisateur

GYS

GYS PROTIG 201 AC/DC Manuel utilisateur

TAFA

TAFA 30*8B35 Manuel utilisateur

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuel utilisateur

ESAB

ESAB Buddy Arc 145 Manuel utilisateur

CIGWELD

CIGWELD 636804 Guide rapide

Red-D-Arc

Red-D-Arc DC-400 Manuel utilisateur

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuel utilisateur

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuel utilisateur

WIA

WIA Weldmatic 270 CP132-2 Manuel utilisateur

Sonics

Sonics H520T Manuel utilisateur

Miller

Miller Big Blue 400D Manuel utilisateur

NewArc

NewArc RT2000 Guide de démarrage rapide

Hypertherm

Hypertherm powermax1000 Manuel utilisateur