Lassco Spinnit EBM-2.1 Manuel utilisateur
Provided By
http://www.MyBinding.com
http://www.MyBindingBlog.com
Lassco Spinnit
EBM-2.1 Paper Drill
User's Manual
Before operating this equipment, please read these
instructions completely and keep these operating
instructions for future reference.
Serial Number:
Date of Purchase:
Dealer:
Address:
Telephone Number:
485 Hague Street, Rochester, NY 14606 U.S.A.
Tel: 585-436-1934 Fax: 585-464-8665
www.lasscowizer.com info@lasscowizer.com
Table Of Contents
Introduction
Operating Instructions
Maintenance
Trouble Shooting Guide
Introduction.......................................................................
Shipping Damage Inspection............................................
Page 02
Page 02
Safety Information
Safety Instructions.............................................................
Warning Labels..................................................................
Page 03
Page 03
Setting Up Your Machine
Loose Materials Inventory.................................................
Table Assembly.................................................................
Backgauge Assembly.......................................................
Paper Side Stops..............................................................
Chip Bag...........................................................................
Pattern Bars......................................................................
Electrical Start Up.............................................................
Page 04
Page 05
Page 06
Page 06
Page 07
Page 07
Page 07
Drill Bit Removal and Installation......................................
Leveling The Drill Bits.......................................................
Drillilng..............................................................................
Traversing the EZ-Glide Table..........................................
Clearing the Chips............................................................
Tips On Drilling.................................................................
Page 08
Page 09
Page 09
Page 09
Page 10
Page 10
Parts Diagrams
Front, Side, and Back View...............................................
Interior Front and Back......................................................
Parts List...........................................................................
Page 13
Page 14
Page 15
Every 6 Months................................................................. Page 11
Problem, Cause and Correction........................................
Page 12
Page 01
Introduction
Shipping Damage Inspection
Page 02
Thank you for your purchase of the Spinnit EBM-2.1 Paper Drill. Lassco-Wizer
has been designing and manufacturing proven performance equipment for the
graphic arts, office, screen printing, sign, awards and engraving industries for
over 60 years.
We ask that you take a moment to fill in the serial number and other information
on the front cover of this manual. Please keep this manual as a reference for
future use.
For parts and service please contact the Lassco-Wizer Dealer from whom you
purchased the machine. If you require assistance in locating a Lassco-Wizer
Dealer nearest you, please contact our customer service department at
585-436-1934. Please have the model of your machine and the serial number
when you call.
If you wish to write to us please contact us at:
Lassco-Wizer
485 Hague Street
Rochester, NY 14606
Remove the machine from the carton and inspect for any shipping damage. If any
damage is present, report the damage to the carrier immediately. Failure to do so
may void any warranties.
Introduction
Safety Information
Page 03
All operators must read and understand the Users Manual and all other safety instruc-
tions before using this equipment. If after reading the manual you are still uncertain
about use, please contact a Service Technician for assistance. If you need contact
information for a Service Technician nearest you please call 585-436-1934. Failure to
fully understand the safety instructions can result in personal injury.
This machine is designed for one person operation. Never operate the machine with
more than one person.
Safety of this equipment is the responsibility of the users.
Keep hands, hair, and loose clothing away from the drills.
Please read and follow all warning labels on your machine.
Always turn the machine off and wait for the drills to stop spinning before installing or
removing drill bits. Keep hands away from drills when operating. PLEASE NOTE THAT
THE DRILL BITS MAY BE HOT AFTER USE. PROCEDE WITH CAUTION WHEN
CHANGING THE DRILL BITS.
ONLY A SERVICING TECHNICIAN IS TO SERVICE THIS MACHINE.
Warning Labels
Safety Instructions
The following labels appear on your EBM-2.1 paper drill. Make
sure all operators understand and follow the safety instructions.
Please read and make sure that all operators understand the operators
manual and all other safety instructions before using this equipment.
Keep hair, jewelry, loose clothing and any other items that could become
entangled pulled back away from the machine when drilling.
Setting Up Your Machine
Loose Materials Inventory
Page 04
Remove and inspect the following items:
2-3/4
3-1/2
2-3/4
4-1/4
items are not to scale
EZ-114A: Table Assembly (1)
EZ-115A: Backgauge (1) EZ-1016 Pattern Bars (set of 5)
FM4-4007: Side Stop Screws (4)FM4-4006: Paper Side Stops (2)
EBM2-1048: Chip Bag (1)
This item comes installed
Hollow Drill BIt (1)
Spin-Eze:
Drill Bit Lubricant (1)
CC-2: Chip Clearer (1) EBM-32:
Chuck Release Key (1)
EBM2-1034: Drill Strip (1)
(This item comes installed
on the table as shown)
HEX-332:
Hex Wrench 3/32” (1)
HEX-18:
Hex Wrench 1/8” (1)
One of these items
comes installed
EZ-1014: Table Stop (2)
1/4” Lock Washers (2)
10-32 Elastic Stop Nuts (2)
EBM-76:
Black F ber Washer (1)
50-35: 5/16”-18
Elastic Stop Nut (1)
EZ-1028: Clamp Bracket (1) &
FM7-7005: 1/4” Knob (1)
Setting Up Your Machine
Table Assembly Installation
Page 05
Grasping the Table and depressing the Release
Handles to unlock the Table Pin, slide the V-Bars
located on the underside of the Table into the
V-Rollers on the Base of the machine as shown.
Step #1
Attach the second Table Stop (EZ-1014) to the
underside of the table using two 1/4” lock washers
and two 10-32 Elastic Stop Nuts as shown. Tighten
with a wrench until secure.
Step #2
Note: Please note that one of the Table Stops (EZ-1014) comes
installed. Make sure when installing the Table onto the
Base you are sliding it from right to left (while facing the
machine) to avoid obstruction from the pre-installed Table
Stop.
Note: Please note that, although they are factory set, you may have to adjust the cams on the
V-Rollers if the Table is too tight or too loose after installation. If so, remove the Table.
With an open-end wrench and holding the screw head in place with a screwdriver, adjust
the cam spacers under the V-Rollers. If the Table is too tight, adjust the V-Rollers out
towards the edge of the Fork Plate (EZ-1000). If the Table is too loose, adjust the
V-Rollers in toward the center of the Fork Plate.
V-Bars
Release
Handles
Underside of Table
Table Pin
Table Slide Stop
1/4” Lock Washers
10-32 Elastic Stop Nuts
V-Rollers
Cam Spacers
Fork Plate
Setting Up Your Machine
Backgauge Assembly
Page 06
Step #4
Step #3
Paper Side Stops
Attach the Paper Side Stops (FM4-4006) using two
Side Stop Screws (FM4-4007) each. Position the
Paper Side Stop as desired and tighten down with
light pressure.
Step #5
Attach the Backguage to the Table by hooking the left
end over the Side Iron (FM4-4003) on the side as shown
in the accompanying picture. Align both ends of the
Backgauge using the Table Scales (3S-14) so that it is
squared correctly. When it is positioned as desired
tighten down the Clamp Bracket Knob as shown.
Assemble the Backgauge by placing the Black Fiber Washer (EBM-76) over the Threaded
Stud. Place the Clamp Bracket (EZ-1028) on the Threaded Stud with the knob end
toward the center of the assembly. Tighten the Elastic Stop Nut on the Threaded Stud
with a wrench until it is snug, allowing the Clamp Bracket to move with slight resistance.
Note: Do not position the Backgauge too close to the hollow drill bit
so that it touches. This can cause serious damage to the
hollow drill bit causing it to break or shatter. The Backgauge
must be at least 1/8” from the circumference of the hollow drill
bit.
Clamp Bracket & 1/4” Knob
Black Fiber Washer
5/16”-18 Elastic Stop Nut
Threaded Stud
Setting Up Your Machine
Chip Bag
Pattern Bars
Page 07
Your EBM-2.1 comes with five pattern bars
included. Four common patterns and one blank
pattern as shown.
Insert a Pattern Bar by loosening the Pattern Bar
Stop (EZ-1022) and inserting the desired pattern
into the slot on the Pattern Bar Guide as shown in
the diagram. Insert the angled end into the slot as
far as it will go so that the slot at the end of the
Pattern Bar lines up with the Pattern Bar Stop.
When you have the pattern correctly inserted,
tighten down the Pattern Bar Stop through the slot
on the Pattern Bar locking it in place.
Step #7
Electrical Start Up
Making sure nothing is interfering with the drill bit,
plug the cord set into a grounded 115V outlet. To
turn the machine on, press the Rocker Switch on the
upper left hand side of the shroud.
Step #8
2-3/4
3-1/2
2-3/4
4-1/4
Blank (Customizable)
3 holes 2-3/4” apart center to center
3 holes 3-1/2” apart center to center
2 holes 2-3/4” apart center to center
3 holes 4-1/4” apart center to center
(standard three ring binder)
Your Spinnit Paper Drill is now ready for use. With proper operation and
maintenance, it will give you trouble free operation for years.
Attach the chip bag as shown by stretching the
open end over the top hook of the chip chute.
Continue fitting it around the entire edge of the chip
chute making sure it is snug.
Step #6
Note: Be sure to empty the chip bag regularly as needed. Failure
to empty the chip bag can result in clogging of the chip
chute.
Power Cord
Rocker Switch
Operating Instructions
Drill bit Removal and Installation
Page 08
Remove the hole guard which is attached to the chuck. This
is done by grasping the bent end and sliding the guard off.
Step #1
Using the Chuck Release Key (EBM-32), insert the tapered
end facing down into the chuck hole. With a clockwise motion
turn the Chuck Release Key 45 degrees. The drill bit will slide
out of the chuck. It is recommended that you hold onto the
drill bit so that it does not drop out of the chuck damaging the
tip.
Step #2
To install a drill bit, grasp the drill bit, and being careful to keep
it straight, press it up into the chuck.
Step #3
Seat the drill bit by using a stack of scrap paper or a phone
book. Set the scrap on the table as shown and pull lightly
down on the handle to raise the table toward the drill bit. Put
light pressure on the hollow drill bit seating it firmly in place.
Remove the scrap paper and turn the machine on to check the
concentricity of the bit. If the bit is not concentric, remove it
and repeat steps 3 and 4 until it is concentric. When the drill
bit is correctly installed replace the hole guard back onto the
chuck to protect debris from clogging the chuck.
Step #4
Note: Please note that drill bits may be hot after drilling. Please wait to
change drill bits until they have cooled down.
Autres manuels pour Spinnit EBM-2.1
1
Table des matières
