Larson Electronics EPL-BS-25WRE Manuel

EPL-BS-25WRE

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 2

EPL-BS-25WRE Instruction Guide

25 Watt Portable Explosion Proof LED Light

Thank you for your purchase of the Larson Electronics EPL-BS-25WRE series light. This light is completely assembled,

tested and ready for use when shipped from the factory. Please follow the steps below in order to operate and maintain

this product.

IMPORTANT

READ CAREFULLY BEFORE OPERATING THIS LIGHT. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. IF UNSURE

ABOUT ANY PART OF THESE INSTRUCTIONS, CONSULT A QUALIFIED ELECTRICAL PROFESSIONAL. THE EPL-BS-25WRE

MUST BE OPERATED IN ACCORDANCE WITH NATIONAL ELECTRICAL CODE AND ALL APPLICABLE LOCAL CODES. PROPER

GROUNDING IS REQUIRED FOR SAFETY.

FOR PERSONAL SAFETY, ALWAYS CONFIRM THE RATING OF ANY KNOWN HAZARDOUS OR POTENTIALLY HAZARDOUS

LOCATION WHERE THE LIGHT IS TO BE USED.

WARNING: OPERATE ONLY AT THE VOLTAGE LISTED ON THE PRODUCT LABEL.

WARNING: TO PREVENT IGNITION OF A HAZARDOUS ATMOSPHERE, THE SUPPLY CIRCUIT SHOULD BE DISCONNECTED

WHEN INSTALLING OR PERFORMING ANY MAINTENANCE ON THIS UNIT.

WARNING: WHEN INSTALLING THIS LIGHT IN HAZARDOUS LOCATIONS, CHECK THE OPERATING TEMPERATURE LIMITS

PRIOR TO INSTALLATION TO BE SURE IT CONFIRMS TO THE ENVIRONMENTAL TEMPERATURE RESTRICTIONS AND NEC

CLASSIFICATIONS. CHECK THE FIXTURE’S METAL NAMEPLATE FOR TEMPERATURE (T) RATINGS.

WARNING: DO NOT SCRATCH OR CHIP THE FRONT LENS. TURN THE POWER OFF BEFORE STARTING INSTALLATION OR

REPAIR.

WARNING: OPERATE THIS FIXTURE ONLY AT THE VOLTAGE OF YOUR SPECIFIC SUPPLY CIRCUIT. FAILURE TO DO SO

WILL RESULT IN DAMAGE TO THE FIXTURE.

WARNING: SUBSTITUTE COMPONENTS MAY IMPAIR EXPLOSION PROOF SAFETY.

INSTALLATION

Before operation, confirm that the power source will provide the correct voltage

indicated on the product nameplate. Ensure the receptacle will accept the cord cap

attached to the light.

Check product nameplate for Ratings and Approvals.

Place the light in the desired location and run its power cord to a power source.

Ensure all safety requirements are followed for the hazardous area.

This light is instant-on and will illuminate once energized.

Multi-voltage capability allows this light to be powered via

Voltage: 120-277V AC, 50/60Hz

Aluminum base stand mount contains thru-holes for permanently or temporarily securing to surface with appropriate

screws.

ADJUSTMENT

Loosen the hand screw on side of the light to make vertical adjustments. Tighten hand screw once desired angle is

achieved.

The light can be mounted in any direction to a sturdy metallic surface. Ensure the mounting surface can withstand the

weight.

When removing, pull light straight off. Do not drag the magnets as this could scratch the surface light is mounted to.

Use the handle on top for easy maneuverability.

EPL-BS-25WRE

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 2

MAINTENANCE

1. Perform visual, electrical, and mechanical inspections on a regular basis. The environment and frequency of use

should determine this. However, it is recommended that checks be made at least once a year. We recommend an

Electrical Preventive Maintenance Program as described in the National Fire

2. Protection Association Bulletin NFPA No. 70B: Recommended Practice For Electrical Equipment Maintenance

(www.nfpa.org).

3. The lens should be cleaned periodically to ensure continued lighting performance. To clean, wipe the lens with a

clean, damp cloth. If this is not sufficient, use a mild soap or a liquid cleaner such as Collinite NCF or Duco #7. Do

not use an abrasive, strong alkaline, or acid cleaner. Damage may result.

4. Visually check for undue heating evidenced by discoloration of wires or other components, damaged parts, or

leakage evidenced by water or corrosion in the interior. Replace all worn, damaged, or malfunctioning components,

and clean gasket seals before putting the luminaire back into service.

5. Electrically check to make sure that all connections are clean and tight.

6. Mechanically check that all parts are properly assembled.

TROUBLESHOOTING

Refer to the guide below or contact the manufacturer if the fixture does not function properly.

Is the correct line voltage being supplied to the fixture?

Is the fixture properly grounded?

These instructions may not cover all details or variations of this product for your equipment or installation

requirements. Should further information not covered by these instructions be required, please contact Larson

Electronics at 1-800-369-6671 for further assistance.

Please visit LarsonElectronics.com for Warranty and Return information.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Larson Electronics Lampe de travail

Larson Electronics

Larson Electronics WAL-WBC-500LTL-LED-100 Manuel utilisateur

Larson Electronics

Larson Electronics L810 Manuel utilisateur

Larson Electronics

Larson Electronics EPL-FL-26 Manuel utilisateur

Larson Electronics

Larson Electronics EPL-QC-16C-2X50LED-RT-X24V-C1D1-12.3-100-EPP Manuel utilisateur

Larson Electronics

Larson Electronics WAL-QP-2X500LTL-LED-100 Manuel utilisateur

Larson Electronics

Larson Electronics EPLC2-MB-100LED-100 Manuel utilisateur

Larson Electronics

Larson Electronics WAL-TP-2X50E-1224 Manuel utilisateur

Larson Electronics

Larson Electronics RSLED Manuel utilisateur

Larson Electronics

Larson Electronics EPL-PM-150LED-X24I-100 Manuel

Larson Electronics

Larson Electronics WAL-TP.S-2XRL16-LED Manuel utilisateur

Larson Electronics

Larson Electronics EPL-BS-150HPS Series Manuel

Larson Electronics

Larson Electronics LED10W-1X2LT Manuel utilisateur

Larson Electronics

Larson Electronics LEDWP-600E-OS Manuel

Larson Electronics

Larson Electronics EPL-BS-70LED-6XMB-150X12 Manuel

Larson Electronics

Larson Electronics EHL-LED-120X12V-XGFI Series Manuel utilisateur

Larson Electronics

Larson Electronics WAL-TP.S-RL16-LED Manuel utilisateur

Larson Electronics

Larson Electronics WL-LED-12-M Manuel utilisateur

Larson Electronics

Larson Electronics EPL-16C-1MLED Manuel utilisateur

Larson Electronics

Larson Electronics EXPRL-98 Manuel utilisateur

Larson Electronics

Larson Electronics GL-9900 Manuel

Larson Electronics

Larson Electronics WDL-12-IPS-LED-1227 Manuel utilisateur

Larson Electronics

Larson Electronics GNM-LEDWL-25W Manuel

Larson Electronics

Larson Electronics WAL-BP-3XLED-CPR Manuel utilisateur

Larson Electronics

Larson Electronics EHL-LED-240X12V-50 Manuel utilisateur

Manuels Lampe de travail populaires d'autres marques

ANSMANN

ANSMANN POWERLIGHT 5.1 Manuel utilisateur

RTRMAX

RTRMAX RTX1868 Manuel utilisateur

FeinTech

FeinTech LAL00220 Manuel utilisateur

Bunker Hill Security

Bunker Hill Security 64735 Manuel utilisateur

Goobay

Goobay 30450 Manuel utilisateur

REV Ritter

REV Ritter SPOT Manuel utilisateur

Ignition

Ignition Stagepix Line 100 IP Manuel utilisateur

SCANGRIP

SCANGRIP DUO CONNECT Manuel utilisateur

Bosch

Bosch GLI 18 V Manuel utilisateur

Bayco

Bayco SL-1514 Manuel utilisateur

EUFAB

EUFAB SMD LED 8+1 Manuel utilisateur

DeWalt

DeWalt DCL510 Manuel utilisateur

PowerSmith

PowerSmith PWLD080T Manuel utilisateur

MaxLite

MaxLite 73683 Manuel utilisateur

Heitronic

Heitronic Trend 27867 Manuel utilisateur

Monzana

Monzana Gore MZCL10 Manuel utilisateur

EINHELL

EINHELL TE-CL 18/2000 LiAC Manuel utilisateur

Bayco

Bayco NIGHTSTICK Dual-Light Xtreme Lumens... Manuel utilisateur