Larson Electronics HAL-MB-185LED-CPR-100 Manuel utilisateur

HAL-MB-185LED-CPR-100

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 2

185 Watt Hazardous Location LED Light - Magnetic

Mount - C1D2 - ATEX - 100 foot Cord w/ EXP Plug

Instruction Manual

This explosion proof light is designed for illumination of industrial locations. It uses the latest in solid state

lighting technology for long life, low maintenance and high efficiency.

The unique design focuses the light where it is needed, giving improved efficiency over a conventional

HIDluminaire.

An internal, universal input, power-factor-corrected switch-mode supply allows it to be used from any

nominal 90-305V AC, 50/60Hz supply without any variation in light output.

WARNING

To avoid the risk of fire, explosion or electric shock, this product should be installed, inspected and

maintained by a qualified electrician only, in accordance with all applicable electrical codes.

To avoid electric shock:

Be certain electrical power is OFF before and during installation and maintenance.

Luminaire must be connected to a wiring system withan equipment-grounding conductor.

To avoidexplosion:

Make sure the supply voltage is within the luminaires’ voltage rating.

Ensure the marked T rating is less than the ignition temperature of the Hazardous Atmosphere.

Do not operate in ambient temperatures abovethose indicated on the luminaire nameplate.

Do not operate if the lens is cracked or damaged. All fasteners shouldbe properly seated.

MOUNTING

This explosion proof LED light fixture is comprised of a 16x14 inch LED light head mounted atop a legged

base stand fabricated from non sparking aluminum, with a separate shelf type magnetic mounting

bracket that allows mounting to ferrous metallic surfaces. The lamp can be easily adjusted up or

down 90 degrees and locked into position by simply loosening the two T-handle adjustment screws

located on either side of the light head and retightening them once the desired angle is found. The

magnetic mounting bracket for this unit includes six 200 lbs. grip magnetic bases which provide a total of

1,200 lbs. of grip and allows operators to mount the unit to walls and flat metallic surfaces. Users simply

attach the magnetic mounting bracket to the desired surface, then hang the lamp assembly from the

bracket.

WARNING: If there is moisture present, or chance of it, in the conduit system then necessary

precautions should be taken by the installer to prevent the moisture from entering through the cable or

conduit and entering the fixture. Failure to comply with the above could void the warranty.

HAL-MB-185LED-CPR-100

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 2

WIRING (see attached wiring diagram)

This unit comes preconfigured with selected cord cap. The is outfitted with 100` of 16/3 chemical and

abrasion resistant SOOW cord that is fitted with an explosion proof cord cap for easy connection to

explosion proof outlets. Plug options include a 5-15 15 amp straight blade plug for use with 120V

explosion proof outlets, a 5-20 20 amp straight blade plug for use with 120V explosion proof outlets,

or a 6-20 20 amp straight blade plug for use with 220-240V explosion proof outlets. **PLEASE

NOTE** voltage ratings on plugs and outlets are MAXIMUM voltage. For low voltage applications,

proper voltage must be applied to the outlet or damage to the light fixture will occur.

MAINTENANCE

Caution: To avoidpersonal injury, disconnect power to the light and allow the unit to cool down before

performing maintenance.

Warning:No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens will

voidthe warranty.

1. Perform visual,mechanical and electrical inspections on a regular basis. We recommend routine

checks to be made on a yearly basis. Frequency of use and environment should determine this. It

is recommendedto follow an Electrical Preventive Maintenance Program as described in NFPA

70B: Recommendedpractice for Electrical Equipment.

2. The lens should be cleaned periodically as neededto ensure continued photometric performance.

Clean the lens with a damp, non-abrasive,lint-free cloth. If not sufficient, use mild soapor a liquid

cleaner.

3. Inspect the cooking fins on the luminaire to ensure that they are free of any obstructions or

contamination (i.e.excessive dust build-up). Clean with a non-abrasive cloth if

needed.

4. Do not operate if the lens is cracked or damaged. All fasteners shouldbe properly seated.

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS. SHOULD FURTHER

INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT [email protected] OR BY PHONE AT

1-800-369-6671 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

Table des matières

Autres manuels Larson Electronics Équipement d'éclairage

Larson Electronics

Larson Electronics EPL-HB-100LED-RT-CM Manuel utilisateur

Larson Electronics

Larson Electronics HALPRM-PS-1000WMH Manuel utilisateur

Larson Electronics

Larson Electronics EPL-48-2L-LED-BLC Manuel utilisateur

Larson Electronics

Larson Electronics EPL-LB-50LED-RT-180B Manuel utilisateur

Larson Electronics

Larson Electronics EPL-HB-150LED-RT-IBSC Manuel utilisateur

Larson Electronics

Larson Electronics EPL-HB-150LED-RT Manuel utilisateur

Larson Electronics

Larson Electronics ATX-EXPCMR-BP-HH-QXGA Manuel utilisateur

Larson Electronics

Larson Electronics GAU-ID-36-1L-UVC-SPF Manuel utilisateur

Larson Electronics

Larson Electronics EPL-QP-2X150RT Manuel utilisateur

Larson Electronics

Larson Electronics EXHL-TRN-LE4-FKWL Series Manuel utilisateur

Larson Electronics

Larson Electronics LM Multi Stage Series Manuel utilisateur

Larson Electronics

Larson Electronics EPLC2-QP-1X70LED-100 Manuel utilisateur

Larson Electronics

Larson Electronics VFD-1P-220.240-1HP-7A-DCM Manuel utilisateur

Larson Electronics

Larson Electronics EPLC2-48-100LED-AMB Manuel utilisateur

Larson Electronics

Larson Electronics VPLHL-7WLED-PC-GR30 Manuel utilisateur

Larson Electronics

Larson Electronics LEDLB-4-IR Manuel utilisateur

Larson Electronics

Larson Electronics EPL-150LED-RT-SP0010-200C Series Manuel utilisateur

Larson Electronics

Larson Electronics HAL-16C-185LED-CPR-100 Manuel utilisateur

Larson Electronics

Larson Electronics EPLC2-PT-2X150LED-RT Manuel utilisateur

Larson Electronics

Larson Electronics HAL-LED-SOL12-STCHN.25 Manuel utilisateur

Larson Electronics

Larson Electronics FRL-EMX-18-90W-FUVC-KT Manuel utilisateur

Larson Electronics

Larson Electronics LEDLB-12ET-IR-M Manuel utilisateur

Larson Electronics

Larson Electronics EPL-HB-150LED-RT-480V-IBSC Manuel utilisateur

Larson Electronics

Larson Electronics IND-LP-SS-24-2X2-2L-UVC Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur