Larson Electronics EPL-HB-150LED-RT-NSF Manuel utilisateur

EPL-HB-150LED-RT-NSF

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 2

150W Explosion Proof Food Safe LED Light Fixture

C1D1/C2D1 - 17500 Lumens - No Exposed Glass

Instruction Manual

This explosion proof light is designed for illumination of industrial locations. It uses the latest in

solid state lighting technology for long life, low maintenance and high efficiency.

The unique design focuses the light where it is needed, giving improved efficiency over a

conventional HID luminaire.

This light fixture is shipped preconfigured to work in the selected voltage range. This includes 100-

277V AC 50/60hz or 11-25V AC/DC depending on model selected. An internal, universal input power-

factor-corrected switch allows it to be used from any voltage within range without variation in light

output. Check product label for correct input voltage!

WARNING

To avoid the risk of fire, explosion or electric shock, this product should be installed, inspected

and maintained by a qualified electrician only, in accordance with all applicable electrical codes.

To avoid electric shock:

•Be certain electrical power is OFF before and during installation and maintenance.

•Luminaire must be connected to a wiring system with an equipment-grounding conductor.

To avoid explosion:

•Make sure the supply voltage is within the luminaires’ voltage rating.

•Ensure the marked T rating is less than the ignition temperature of the Hazardous

Atmosphere.

•Do not operate in ambient temperatures above those indicated on the luminaire nameplate.

•Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.

For supply connections, use wire rated for at least 110°C

Recommended mounting height is 25-40 feet.

MOUNTING

This fixture offers an adjustable mounting system that allows it to be mounted to any flat surface

including walls and ceilings. A single ½-13 bolt is used to mount the fixture to the surface.

Check to ensure that all mounting hardware is included.

•2 Small Brackets

•1 Large Trunnion Bracket

•8 Bolts

•8 Lock-Washers

•4 Nuts

When pendant mounting,

thread cable through

approved condui

t and

thread conduit to back of

fixture. Tighten set bolt

after at least 5 full threads.

EPL-HB-150LED-RT-NSF

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 2

1. Using four bolts, washers and the four nuts provided, attach brackets “A” to both sides of bracket

“B”.

2. The LED fixture has 9 holes for a versatile mount option. Select the holes that you would like to

use.

3. Brackets “A” will then be bolted to the LED fixture with the remaining bolts and washers.

4. The fixture is now ready for installation.

5. A safety cable and eye bolt are included for additional safety.

WIRING (see attached wiring diagram)

This unit comes preconfigured in the selected voltage, beam angle, and color temperature. Wire light

to the correct voltage. Follow all applicable local, state, and National Electrical Code for the

hazardous area!

POLYCARBONATE LENS

There are 8 clips holding the lens in place. Each clip snaps in place on the fixture holding the lens.

The lens can be removed if necessary for replacement. Refer to EPL-HB-150LED-RT-188 instructions.

MAINTENANCE

Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool

down before performing maintenance.

Warning: No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens

will void the warranty.

1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend

routine checks to be made on a yearly basis. Frequency of use and environment should

determine this. It is recommended to follow an Electrical Preventive Maintenance Program

as described in NFPA 70B: Recommended practice for Electrical Equipment.

2. The lens should be cleaned periodically as needed to ensure continued photometric

performance. Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use

mild soap or a liquid cleaner.

3. Inspect the cooking fins on the luminaire to ensure that they are free of any obstructions

or contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if

needed.

4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS. SHOULD FURTHER

INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT SALES@LARSONELECTRONICS.COM OR BY PHONE AT

1-800-369-6671 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

WARNING: CHECK NAMEPLATE

FOR PROPER VOLTAGE. DAMAGE

FROM IMPROPER VOLTAGE WILL

VOID WARRANTY.

Brackets “A”

Bracket “B”

Trunnion Bracket

Table des matières

Autres manuels Larson Electronics Équipement d'éclairage

Larson Electronics

Larson Electronics XLE-UVC-XX-SGKT-2X Manuel utilisateur

Larson Electronics

Larson Electronics GL-2051-F-M Manuel utilisateur

Larson Electronics

Larson Electronics LED18W-PAR36 Manuel utilisateur

Larson Electronics

Larson Electronics WCDE-11-6HPS-MR Manuel utilisateur

Larson Electronics

Larson Electronics IIND-DBL-36-1L-R1-120V Manuel utilisateur

Larson Electronics

Larson Electronics EPL-HB-2X150LED-RT Manuel utilisateur

Larson Electronics

Larson Electronics EPL-FL1524-LED-100 Manuel utilisateur

Larson Electronics

Larson Electronics EPLC2-LED-50W-RT-JB5 Manuel utilisateur

Larson Electronics

Larson Electronics EPL-HB-150LED-RT-140DB-JB3 Manuel utilisateur

Larson Electronics

Larson Electronics EPL-TP-2XRUL10 Manuel utilisateur

Larson Electronics

Larson Electronics EPLC2-LED-150W-RT-DNS Manuel utilisateur

Larson Electronics

Larson Electronics EPL-LB-50LED-RT-180B Manuel utilisateur

Larson Electronics

Larson Electronics HL-85-LED-CPR-30-TRP Manuel utilisateur

Larson Electronics

Larson Electronics WAL-HL-2000W-240V Manuel utilisateur

Larson Electronics

Larson Electronics GL-2051-M Manuel utilisateur

Larson Electronics

Larson Electronics PTB-1-75FT Manuel utilisateur

Larson Electronics

Larson Electronics C1D2 Manuel utilisateur

Larson Electronics

Larson Electronics EPLX-SL-PT-3X80W.RD2-TRC-20X-100C Manuel utilisateur

Larson Electronics

Larson Electronics LED10W-1X4LT Manuel utilisateur

Larson Electronics

Larson Electronics TPM-GL20004-12C-1227-10C Manuel utilisateur

Larson Electronics

Larson Electronics EPL-TL-2X10W-C-PA Series Manuel utilisateur

Larson Electronics

Larson Electronics EPL-EMG-CM-42W Mode d’emploi

Larson Electronics

Larson Electronics EPL-PM-1X30LED-6XMB-10 Manuel utilisateur

Larson Electronics

Larson Electronics EPL-PM-50LED-100 Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur