Lantronix MSS4 Manuel utilisateur

Assign IP

Caution: The IP address you assign must be within

a valid range, be unique to your network, and be

in the same subnet as your PC.

Note: For the convenience of assigning an IP address

over your Ethernet network, refer to the “Using ARP

and Ping” section of the Installation Guide.

1) Connect a null modem cable between your computer

and the unit’s console port (#1).

2) Open a terminal emulator (e.g., Hyperterminal).

3) Confirm that the configuration parameters are set

as follows: 9600 Baud, 8/N/1, Xon/Xoff flow control.

4) Press the Enter key.

5) Enter any user name.

6) At the local prompt enter: set privileged

7) Enter system for the password.

8) At the local prompt enter:

change server ipadd [xxx.x.x.xx.]

Configure

1) Open a Web browser.

2) Enter the IP address you just assigned into the URL

address field.

3) Confirm that the following screen displays:

4) Click on the Port Properties heading.

The MSS4 network-enables Industrial Automation,

Medical Instruments, modems, and other serial devices.

Each of its four ports can accommodate RS232, RS422, or

RS485 communication.

The MSS4 delivers remote management and data accessi-

bility through its 10/100BASE-T Ethernet port or its

optional 100BASE-FX fiber link port. Its two optional PC

card slots provide flash storage or wireless Ethernet.

This Quick Start explains how to connect, configure, and

troubleshoot your unit. For more detailed information,

refer to the MSS Installation Guide and Reference Manual

on the CD ROM supplied with this product.

Connections

1) Place the MSS4 near your serial devices

2) Connect your Ethernet cable to the unit’s RJ45

Ethernet port.

3) Optionally, connect your full duplex fiber optic Ethernet

cables to the unit’s ST connectors.

Note: If you wish to use the optional Power Terminal

Block, refer to the Installation Guide.

4) Connect power (9 to 30 VDC, 3W maximum).

5) Wait about 30 seconds.

6) Confirm that the Link LED lights up.

7) Confirm that the OK LED is slowly blinking.

8) Note the pin assignments of the terminal blocks

and DB9 connectors:

Power, Serial, Ethernet Connections

MSS4

Quick Start

MSS4

serial 4

serial 3

serial 2

serial 1

pccard 1

pc card 2

link

10/100

100 BaseFX

TX RX

serial 1

reset

pc card

9-30vdc

Ethernet

Optional

Fiber

Computer

Serial Device

Reset

Button Mounting

Bracket

Optional

PC Card

Slots (2)

Power

Terminal

Block

RJ45

Jack

Console

Port

DTR

CTS

RTS

DSR

Grd.

TX+

RX+

TX-

RX-

7 1

DSR

CTS

Grd.

RTS

DTR

7 1

RX-

RX÷

Grd. TX÷

TX-

RS-485

RS-232

5) Enter System.

6) Click on the Login button.

7) Confirm that the following screen displays:

8) Select a port.

9) Confirm that your serial device(s) on that port match

the serial parameters listed on the screen.

10) Repeat the last two steps for the other ports.

11) Click the Update Port Settings button.

12) Power cycle the unit to reboot.

PC Card Slot Options

The two optional PC card slots accept Type I/II PC cards.

The bottom slot also accepts Type III cards. Neither sup-

ports hot-swapping; rather, you must reboot the unit any

time you insert a PC card. Refer to our web site to deter-

mine the most current PC card technologies we support:

http://www.lantronix.com/products/ds/mssvia/cards

Note: 802.11 wireless networking is enabled by

default. To customize its settings, refer to the

Installation Guide on your CD.

1) Disconnect power.

2) Insert your PC card into a PCMICA slot.

3) Connect power to the unit.

4) Wait about 30 seconds.

5) Confirm that the slot’s green LED is lit.

Install

1) Disconnect power.

2) Disconnect your computer from the unit.

3) Optionally, mount the unit.

4) Connect your serial devices to the unit.

5) Connect power to the unit.

Troubleshoot

All MSS4 Models contain eight LEDs. The two LEDs

labeled PC Card 1 and PC Card 2 are operative only on

PC card-equipped models. For all MSS4 models, refer

to the following table:

For PC card-equipped models, refer to the

following table:

Contact

Questions? Call Lantronix Technical Support

at 800-422-7044 or 949-453-3990.

15353 Barranca Parkway

Irvine, CA 92618, USA

Phone: (949) 453-3990

Fax: (949) 453-3995

www.lantronix.com

not lit not in slot

green ready

green, blinking negotiating 802.11 settings

or memory card not formatted

red failure

red, blinking not supported; can’t be read

yellow initializing in progress

yellow, blinking scanning for 802.11 access point

or initialization problem

PCC LED PC Card

900-232 Rev.A

Serial 1 green serial traffic when blinking

Serial 2 green serial traffic when blinking

Serial 3 green serial traffic when blinking

Serial 4 green serial traffic when blinking

OK yellow network activity

green normal runtime code

Link none no Ethernet connection

green 10BASE-T connection

yellow 100BASE-T or -FX connection

LED Color Meaning

Autres manuels pour MSS4

Autres manuels Lantronix Serveur

Lantronix

Lantronix XPress DR+ Mode d’emploi

Lantronix

Lantronix CoBox E2 01 Manuel utilisateur

Lantronix

Lantronix SCS100 Manuel utilisateur

Lantronix

Lantronix SecureBox SDS2100 Manuel utilisateur

Lantronix

Lantronix EDS8PS Manuel utilisateur

Lantronix

Lantronix xport pro Manuel utilisateur

Lantronix

Lantronix C 7/01 Manuel utilisateur

Lantronix

Lantronix xDirect Manuel utilisateur

Lantronix

Lantronix SDS1101 Manuel utilisateur

Lantronix

Lantronix MSS4-D Manuel utilisateur

Lantronix

Lantronix UDS2100 Manuel utilisateur

Lantronix

Lantronix ETS16PR Manuel utilisateur

Lantronix

Lantronix SLC8 Manuel utilisateur

Lantronix

Lantronix EDS4100 Manuel utilisateur

Lantronix

Lantronix CoBox-FL Manuel utilisateur

Lantronix

Lantronix xDirect Manuel utilisateur

Lantronix

Lantronix xSenso 2100 Manuel utilisateur

Lantronix

Lantronix XPort Manuel utilisateur

Lantronix

Lantronix MatchPort b/g Guide de configuration rapide

Lantronix

Lantronix Console Server 800 Manuel utilisateur

Lantronix

Lantronix WiPort NR Manuel utilisateur

Lantronix

Lantronix SLC 8000 Manuel utilisateur

Lantronix

Lantronix UBox UBX4100 Manuel utilisateur

Lantronix

Lantronix xSenso 2100 Manuel utilisateur

Manuels Serveur populaires d'autres marques

HP AlphaServer ES47 Manuel utilisateur

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur