Lanner FX-3230 Manuel utilisateur

Network Appliance

Platform

FX-3230

User Manual

Version: 1.0

Date of Release:2019-02-14

FX-3230 User Manual

The icons are used in the manual to serve as an indication of interest topics or important messages. Below

is a description of these icons:

Note: This mark indicates that there is a note of interest and is something that you should pay

special attention to while using the product.

Warning: This exclamation point indicates that there is a caution or warning and it is something

that could damage your property or product.

The listed websites are links to the on-line product information and technical support.

Resources

URL

Lanner

http://www.lannerinc.com

Product Resource

http://www.lannerinc.com/download-center

RMA

http://eRMA.lannerinc.com

manufacturer reserves the right to make improvements to the products described in this manual at any

time without notice.

No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means

without the prior written permission of the original manufacturer. Information provided in this manual is

intended to be accurate and reliable. However, the original manufacturer assumes no responsibility for its

use, nor for any infringements upon the rights of third parties that may result from such use.

Intel® and Intel® Xeon® are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other

countries.

Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.

All other product names or trademarks are properties of their respective owners.

FX-3230 User Manual

This product has passed the CE test for environmental specifications. Test conditions for passing included

the equipment being operated within an industrial enclosure. In order to protect the product from being

damaged by ESD (Electrostatic Discharge) and EMI leakage, we strongly recommend the use of CE-

compliant industrial enclosure products.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. The operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be required

to correct the interference at his own expense.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. The operation of this

equipment in a residential area is likely to cause harmful interference in which case users will be required to

correct the interference at their own expense.

Follow these guidelines to ensure general safety:

Keep the chassis area clear and dust-free during and after installation.

Do not wear loose clothing or jewelry that could get caught in the chassis. Fasten your tie or scarf and

roll up your sleeves.

Wear safety glasses if you are working under any conditions that might be hazardous to your eyes.

Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.

Disconnect all power by turning off the power and unplugging the power cord before installing or

removing a chassis or working near power supplies

Do not work alone if potentially hazardous conditions exist.

Never assume that power is disconnected from a circuit; always check the circuit.

FX-3230 User Manual

In order not to result in potential electric shock or fire, please avoid improper use narrated below:

Replacing a battery with an incorrect type (e.g. in the case of certain lithium battery types), which can

defeat a safety guard.

Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, which can

result in an explosion.

Leaving a battery in an extremely high temperature surrounding environment, which can result in an

explosion or the leakage of flammable liquid or gas.

A battery subjected to extremely low air pressure that may result in an explosion or the leakage of

flammable liquid or gas.

Lithium Battery Caution:

Risk of Explosion if Battery is replaced by an incorrect type. Dispose of used batteries according to the

instructions.

Installation only by a trained electrician or only by an electrically trained person who knows all English

Installation and Device Specifications which are to be applied.

Do not carry the handle of power supplies when moving to another place.

Electrical equipment generates heat. Ambient air temperature may not be adequate to cool equipment

to acceptable operating temperatures without adequate circulation. Be sure that the room in which you

choose to operate your system has adequate air circulation.

Ensure that the chassis cover is secure. The chassis design allows cooling air to circulate effectively. An

open chassis permits air leaks, which may interrupt and redirect the flow of cooling air from internal

components.

Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD damage occurs

when electronic components are improperly handled and can result in complete or intermittent failures.

Be sure to follow ESD-prevention procedures when removing and replacing components to avoid these

problems.

Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. If no wrist strap is

available, ground yourself by touching the metal part of the chassis.

Periodically check the resistance value of the antistatic strap, which should be between 1 and 10

megohms (Mohms).

Environment:

Do not install and/or operate this unit in any place that flammable objects are stored or used in.

If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack

environment may be greater than room ambient. Therefore, consideration should be given to installing

the equipment in an environment compatible with the maximum ambient temperature (Tma) specified

FX-3230 User Manual

by the manufacturer.

Installation of the equipment (especially in a rack) should consider the ventilation of the system’s intake

(for taking chilled air) and exhaust (for emitting hot air) openings so that the amount of air flow required

for safe operation of the equipment is not compromised.

To avoid a hazardous load condition, be sure the mechanical loading is even when mounting.

Consideration should be given to the connection of the equipment to the supply circuit and the effect

that overloading of the circuits might have on over-current protection and supply wiring. Appropriate

consideration of equipment nameplate ratings should be used when addressing this concern.

Reliable earthing should be maintained. Particular attention should be given to supply connections

other than direct connections to the branch circuit (e.g. use of power strips).

Installation & Operation:

The installation of this product must be performed by trained specialists; otherwise, a non-specialist

might create the risk of the system’s falling to the ground or other damages.

Lanner Electronics Inc. shall not be held liable for any losses resulting from insufficient strength for

supporting the system or use of inappropriate installation components.

Suivez ces consignes pour assurer la sécurité générale :

Laissez la zone du châssis propre et sans poussière pendant et après l’installation.

Ne portez pas de vêtements amples ou de bijoux qui pourraient être pris dans le châssis. Attachez votre

cravate ou écharpe et remontez vos manches.

Portez des lunettes de sécurité pour protéger vos yeux.

N’effectuez aucune action qui pourrait créer un danger pour d’autres ou rendre l’équipement

dangereux.

Coupez complètement l’alimentation en éteignant l’alimentation et en débranchant le cordon

d’alimentation avant d’installer ou de retirer un châssis ou de travailler à proximité de sources

d’alimentation.

Ne travaillez pas seul si des conditions dangereuses sont présentes.

Ne considérez jamais que l’alimentation est coupée d’un circuit, vérifiez toujours le circuit. Cet appareil

génère, utilise et émet une énergie radiofréquence et, s’il n’est pas installé et utilisé conformément aux

instructions des fournisseurs de composants sans fil, il risque de provoquer des interférences dans les

communications radio.

Risque d’explosion si la pile est remplacée par une autre d’un mauvais type.

Jetez les piles usagées conformément aux instructions.

FX-3230 User Manual

L’installation doit être effectuée par un électricien formé ou une personne formée à l’électricité

connaissant toutes les spécifications d’installation et d’appareil du produit.

Ne transportez pas l’unité en la tenant par le câble d’alimentation lorsque vous déplacez l’appareil.

La machine ne peut être utilisée qu’à un lieu fixe comme en laboratoire, salle d’ordinateurs ou salle de

classe.

L’équipement électrique génère de la chaleur. La température ambiante peut ne pas être adéquate pour

refroidir l’équipement à une température de fonctionnement acceptable sans circulation adaptée. Vérifiez

que votre site propose une circulation d’air adéquate.

Vérifiez que le couvercle du châssis est bien fixé. La conception du châssis permet à l’air de

refroidissement de bien circuler. Un châssis ouvert laisse l’air s’échapper, ce qui peut interrompre et

rediriger le flux d’air frais destiné aux composants internes.

Les décharges électrostatiques (ESD) peuvent endommager l’équipement et gêner les circuits

électriques. Des dégâts d’ESD surviennent lorsque des composants électroniques sont mal manipulés et

peuvent causer des pannes totales ou intermittentes. Suivez les procédures de prévention d’ESD lors du

retrait et du remplacement de composants.

Portez un bracelet anti-ESD et veillez à ce qu’il soit bien au contact de la peau. Si aucun bracelet n’est

disponible, reliez votre corps à la terre en touchant la partie métallique du châssis.

Vérifiez régulièrement la valeur de résistance du bracelet antistatique, qui doit être comprise entre 1 et

10 mégohms (Mohms).

Avant d’allumer l’appareil, reliez le câble de mise à la terre de l’équipement à la terre.

Une bonne mise à la terre (connexion à la terre) est très importante pour protéger l’équipement contre

les effets néfastes du bruit externe et réduire les risques d’électrocution en cas de foudre.

Pour désinstaller l’équipement, débranchez le câble de mise à la terre après avoir éteint l’appareil.

Un câble de mise à la terre est requis et la zone reliant les sections du conducteur doit faire plus de 4

mm2 ou 10 AWG.

FX-3230 User Manual

Desserrez la vis du terminal de mise à la terre.

Branchez le câble de mise à la terre à la terre.

L’appareil de protection pour la source d’alimentation CC

doit fournir 30 A de courant.

Cet appareil de protection doit être branché à la source

d’alimentation avant l’alimentation CC.

Lithium Battery Caution: There is danger of explosion if battery is incorrectly replaced. Replace only with

the same or equivalent type. Dispose batteries according to manufacturer's instructions.

Disposal of a BATTERY into fire or a hot oven, or mechanically crushing or cutting of a BATTERY can

result in an EXPLOSION.

Leaving a BATTERY in an extremely high temperature surrounding environment can result in an

EXPLOSION or the leakage of flammable liquid or gas.

A BATTERY subjected to extremely low air pressure may result in an EXPLOSION or the leakage of

flammable liquid or gas.

Suitable for installation in Information Technology Rooms in accordance with Article 645 of the National

Electrical Code and NFPA 75.

Peut être installé dans des salles de matériel de traitement de l'information conformément à l'article 645 du

National Electrical Code et à la NFPA 75.

The machine can only be used in a restricted access location, such as labs or computer facilities with the

proper authorization.

This equipment must be grounded. The power cord for product should be

connected to a socket-outlet with earthing connection.

FX-3230 User Manual

Package Content......................................................................................................................... 11

Ordering Information ................................................................................................................. 11

Optional Accessories .................................................................................................................. 11

System Specifications ................................................................................................................. 12

Front Panel ................................................................................................................................. 13

Rear Panel................................................................................................................................... 15

Block Diagram............................................................................................................................. 16

Motherboard Layout .................................................................................................................. 17

Internal Jumper & Connectors ................................................................................................... 18

Opening the Chassis ................................................................................................................... 24

Installing the CPU ....................................................................................................................... 25

Installing the Disk Drive(s) .......................................................................................................... 31

Installing the NIC Modules ......................................................................................................... 32

Replacing the Cooling Fans......................................................................................................... 34

Replacing the Power Supply Units.............................................................................................. 36

Installing mSATA......................................................................................................................... 37

Installing the System Memory.................................................................................................... 38

Mounting the System ................................................................................................................. 39

Main Setup ................................................................................................................................. 46

FX-3230 User Manual

Advanced Setup.......................................................................................................................... 48

Platform Setup............................................................................................................................ 71

Socket Setup............................................................................................................................... 75

Server Mgmt............................................................................................................................... 85

Security....................................................................................................................................... 90

Boot Setup .................................................................................................................................. 93

Save and Exit Setup .................................................................................................................... 94

Why Dual BIOS?.......................................................................................................................... 97

How Dual BIOS Works ................................................................................................................ 98

Warranty Policy ........................................................................................................................ 102

RMA Service.............................................................................................................................. 102

RMA Service Request Form ...................................................................................................... 103

Table des matières

Autres manuels Lanner Matériel réseau

Lanner

Lanner FW-7551 Manuel utilisateur

Lanner

Lanner NCA-4025 Manuel utilisateur

Lanner

Lanner NCA-2512 Manuel utilisateur

Lanner

Lanner NCA-5540 Manuel utilisateur

Lanner

Lanner ECA-4025 Manuel utilisateur

Lanner

Lanner NCA-5210 Manuel utilisateur

Lanner

Lanner FW-8771 Manuel utilisateur

Lanner

Lanner ICS-P570 Manuel utilisateur

Lanner

Lanner LWR-X8460 Manuel utilisateur

Lanner

Lanner ICS-I372 Manuel utilisateur

Lanner

Lanner FX-3420 Manuel utilisateur

Lanner

Lanner NCA-2522 Manuel utilisateur

Lanner

Lanner HLM-1101 Manuel utilisateur

Lanner

Lanner NCA-1525 Manuel utilisateur

Lanner

Lanner NCA-4035 Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Lanner

Lanner NCA-1040 Manuel utilisateur

Lanner

Lanner NCA-6530 Manuel utilisateur

Lanner

Lanner FW-8760 Manuel utilisateur

Lanner

Lanner NCA-5230 Manuel utilisateur

Lanner

Lanner NCA-4112A Manuel utilisateur

Lanner

Lanner NCA-1040SE Manuel utilisateur

Lanner

Lanner NCA-6520 Manuel utilisateur

Lanner

Lanner NCA-5710 Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur

Cantek

Cantek NR310-4 Manuel utilisateur