Land Pride FD2548 Manuel utilisateur

1/29/04

FD2548

2-Spindle Grooming Mower

10817

310-156M

Operator’s Manual

1/29/04

Cover photo may show optional

equipment not supplied with

standard unit.

Read the Operator’s manual entirely.

When you see this symbol, the

subsequent instructions and

warnings are serious - follow without

exception. Your life and the lives of

others depend on it!

1/29/04

This manual has been prepared to instruct you in the

safe and efficient operation of your 25 Series Grooming

Mower. Read and follow all instructions and safety pre-

cautions carefully.

The parts on your 25 Series Grooming Mower have

been specially designed and should only be replaced

with genuine Land Pride parts. Therefore, should your

Grooming Mower require replacement parts go to your

Land Pride Dealer.

The SAFETY ALERT SYMBOL indicates that

there is a potential hazard to personal safety involved

and extra safety precautions must be taken. When you

see this symbol on your machine or in your manual, be

alert and carefully read the message that follows it.

Record your model number and serial number in the

space provided below. Be sure to bring this information

with you to your dealer when ordering parts or attach-

ments for your Grooming Mower.

SERIAL NUMBER ____________________________

MODEL NUMBER ____________________________

DATE PURCHASED __________________________

TABLE OF CONTENTS

Introduction .............................................................................. 1

Table Of Contents .................................................................... 1

Safety Rules ............................................................................. 2

Safety Decals ........................................................................... 3

Nut & Bolt Torquing Chart ....................................................... 4

Tractor Requirements .............................................................. 4

Gearbox Gear Lube ................................................................. 4

Assembly Instructions .............................................................. 4

Tractor Hook-Up ....................................................................... 5

Powershaft Installation ............................................................. 5

Floating & Front To Back Hitch Adjustments ............................ 5

Leveling The Mower

Three And Four Gauge Wheels ......................................... 6

Two Rear Gauge Wheels & Support Chains ..................... 6

Cutting Height Adjustment ....................................................... 7

Transporting ............................................................................. 7

Mowing Instructions & Adjustments ........................................ 7

Operating Instructions .............................................................. 8

Operating Check List ................................................................ 8

Specifications ........................................................................... 8

Maintenance ............................................................................. 9

Lubrication ................................................................................ 9

Storage ..................................................................................... 10

Options

Anti-Scalping Roller Assembly Instructions ....................... 10

Chain Kit Assembly Instructions ........................................ 11

Trouble Shooting ...................................................................... 12

Warranty ................................................................................... 13

PARTS DRAWINGS

48" Flat Deck Mower Deck ....................................................... 14

Flat Deck Mower Belt Drive ..................................................... 16

Comer Gearbox Assembly ....................................................... 18

IEG Gearbox Assembly............................................................. 20

Gauge Wheel Assembly ........................................................... 22

Power Take-Off ........................................................................ 24

Options

Front Anti-Scalping Roller .................................................. 25

Chain Kit ............................................................................ 26

Safety Decal Placement ........................................................... 27

Mower Decal Placement .......................................................... 28

INTRODUCTION

310-156M

Effective

1/29/04

SAFETY RULES

Most accidents are the result of negligence and carelessness, usually caused by failure of the

operator to follow simple but necessary safety precautions. The following safety precautions are

suggested to help prevent such accidents. The safe operation of any machinery is a big concern

to consumers and manufacturers. Your 48" Grooming Mower has been designed with many

built-in safety features. However, no one should operate this machine before carefully reading

this Owner’s Manual.

1. DO NOT allow anyone to operate this machine who has not been properly trained in its safe

operation.

2. Keep all guards and shields in place and secure.

3. Always use proper PTO speed or machine damage may result. This mower is designed to

be used with a tractor having a 540 rear PTO.

4. DO NOT let children operate the mower.

5. NEVER allow passengers.

6. DO NOT allow anyone but the operator near the mower when operating.

7. Before performing maintenance or making adjustments on the mower, shut off the tractor,

disengage PTO, remove key from ignition, wait for all moving parts to stop and lock brakes

before dismounting tractor. Be sure mower is securely blocked on safe supporting stands

or set completely on the ground.

8. After striking an object, disengage PTO, shut off tractor and inspect for damage before con-

tinuing.

9. DO NOT operate mower too close to ditches. Be alert for holes and gullies. Travel slowly

over rough terrain.

10. Transport mower only in a raised position.

11. Stop engine before leaving tractor.

12. Becertain the tractoris in neutral or parkposition and thePTO is disengagedbefore starting

engine.

13. Check periodically for loose hardware and tighten if necessary.

14. Keep hands, feet and clothing away from moving parts. Wear proper eye protection to pre-

vent injury from flying objects.

15. Mower should be lowered to the ground before engaging PTO and be sure that no one is

near the machine. When traveling on public roads, use accessory lights and devices for ad-

equate warning to operators of other vehicles. Comply with all Federal, State and Local

Laws.

16. Before mowing, clear the area of objects and debris that could become entangled in the

blades or thrown from the mower.

17. NEVER operate the mower while in raised transport position. Disengage the PTO when

raised for transport or backing up.

18. In order to maintain steering control, ballast may need to be added to tractor. To determine

the amount of ballast required refer to your tractor operator’s manual.

1/29/04

SAFETY RULES (CON’T.)

SAFETY DECALS

--IMPORTANT--

* Your Grooming Mower comes equipped with all safety decals in place.

* Always keep safety decals clean and legible.

* Replace all damaged or missing safety decals. To order new safety decals go to your

Land Pride Dealer and reference part numbers as shown on page 27.

* To install new safety decals:

A) Clean the area the decal is to be placed. (Refer to page 27.)

B) Peel backing from decal and press firmly onto surface.

! !

ROTATING CUTTING BLADE

*Do not put hands or feet under or into any part of this mower deck

or discharge chute

*OBJECTS MAY BE THROWN FROM MOWER

* Clear lawn of debris and objects

* Do Not mow with by standards in area

*DO NOT OPERATE MOWER WITHOUT DISCHARGE CHUTE

818-140C

ROTATING CUTTING BLADE

* Do not put hands or feet under or into any part of this mower

deck or discharge chute

818-143C

OPERATE ONLY WITH

540 RPM PTO

818-130C

1. AVOID BODILY INJURY

Objects may be thrown great distances by cutting blades

rotating under deck.

2. BEFORE WORKING ON MOWER:

Disengage power, shut off engine, and make sure blades

have stopped rotating. 818-141C

!CAUTION

DANGER

19. When used in certain sandy soil conditions, there can be severe erosive wearing of the

blade at the lift or wing area. This can cause pieces of the blade to separate and be dis-

charged from the mower. These particles can cause injury or damage and may create the

blade to become unbalanced and dangerous to operate.

ROTATING DRIVELINE

KEEP AWAY!

1/29/04

NUT & BOLT TORQUING CHART

This chart is based on torque requirements in foot pounds for grade 5 bolts.

BOLT DIAMETER MINIMUM TORQUE MAXIMUM TORQUE BOLT DIAMETER MINIMUM TORQUE MAXIMUM TORQUE

1/4" 9 11 3/4" 270 324

5/16" 17 20 7/8" 400 480

3/8" 35 42 1" 580 696

7/16" 54 64 1 1/8" 800 880

1/2" 80 96 1 1/4" 1120 1240

9/16" 110 132 1 3/8" 1460 1680

5/8" 150 180 1 1/2" 1940 2200

NOTE: Torque requirements listed above do not apply to self-locking nuts. For self-locking nuts increase torque

requirements listed above by 15%.

This mower is designed with a 3-Point category I

hitch. Horsepowerratingoftractorshouldnotexceed

26 PTO horse power.

NOTE: In order to maintain steering control, ballast may

have to be added to your tractor. To determine whether

or not to add ballast, refer to your tractor operator’s man-

ual.

ASSEMBLY INSTRUCTIONS

Your 25 Series Grooming Mower is shipped to you almost completely assembled. Remove the protective plastic

wrap from the mower deck. Using a safe lifting device, set the mower deck on a safe supporting stand. Remove

loose components - gauge wheels, gauge wheel arms and miscellaneous hardware from the top of deck. Carefully

follow the instructions below for final assembly.

CAUTION! DO NOT OVER SPEED PTO OR MACHINE DAMAGE MAY RESULT.

THIS MOWER IS DESIGNED TO BE USED WITH A TRACTOR USING A 540 RPM REAR

PTO.

UPPER HITCH ARMS -

Refer to the parts illustration on page 14:

1. Loosen 5/8" x 1 1/2" long bolts (#18) and swing up-

per hitch (#21) up to a vertical position. Remove 5/8" x

5" long bolt (#25) and install upper hitch brace (#22) up-

per pivoting hitch (#23) and hitch spacer (#24) with 5/8"

x 5" longbolt (#25)as shown inparts illustration. Refer

to Fig. 1 on page 5, for bolting location of upper hitch

brace (#22) and tighten hardware to listed torque

above.

GAUGE WHEEL ASSEMBLY - 2 FRONT GAUGE

WHEELS & 4 GAUGE WHEEL ASSEMBLY

Refer to the parts illustration on page 22:

1. Bolt the gauge wheel arms (#1)-front gauge wheel

(#17)-rear gauge wheel, to the mounting channels on

the mower frame using 3/8" x 3" long bolt (#13).

2. Insert the 1" diameter shaft of the gauge wheel yoke

(#6) into the bushings on the gauge wheel arm, noting

the amount of spacers added to top or bottom depend-

ing on cutting height (see "Cutting Height Adjustments"

onpage 7). Secureshaftto wheelarmwith 1/4"lock pin

(#5). Be sure all the spacers are arranged the same on

each wheel assembly. Tighten all hardware to listed

torque.

GAUGE WHEEL ASSEMBLY - 3 GAUGE WHEEL AS-

SEMBLY

Refer to the parts illustration on page 22:

1. Bolt the gauge wheel arms (#1) to the mounting

channels on the mower frame using 3/8" x 3" long bolt

(#13).

2. Rear Single Gauge Wheel: Bolt the gauge wheel

arm (#18) to the mounting channels of the mower frame

using 3/8" x 1 1/4" Long Bolts (#19).

3. Insert the 1" diameter shaft of the gauge wheel yoke

(#6) into the bushings on the gauge wheel arm, noting

the amount of spacers added to top or bottom depend-

ing on cutting height (see "Cutting Height Adjustments"

onpage 7). Secureshaftto wheelarmwith 1/4"lock pin

(#5). Be sure all the spacers are arranged the same on

each wheel assembly. Tighten all hardware to listed

torque.

TRACTOR REQUIREMENTS

GEAR BOX GEAR LUBE

Before operating this unit, 80-90 EP Gear Lube must be added to the gearbox(s) as indicated in the maintenance

lubrication section (Page 9) of this manual. See your Land Pride Dealer for part number 821-012C Gear Lube.

1/29/04

1. Be certain that tractor draw bar will not interfere.

Move draw bar ahead or remove if required. Draw bar

shouldalso be checkedforclearance whenunitis being

raised for the first time.

2. Align lower link arms of tractor to hitch clevises on

mower. Insert lower hitch pins into lower ball swivels

and attach lynch pins.

3. Referring to fig. 1, attach tractor top link to upper

floating hitch on mower with pin supplied. Secure with

lock pin.

4. Adjust thetractor top link in or out to place the upper

hitch pin vertically above the lower hitch pins as shown

in fig. 1(below) to allow mower flotation.

1. Slide powershaft end with extended safety cone

over splined shaft of the gearbox and secure with at-

taching device.

2. Slidepowershaftoverthetractor’ssplinedPTOshaft

and secure with locking device of powershaft.

3. Powershaft should now be moved back and forth to

insure that it is secure on the PTO shaft of the tractor

and mower gearbox.

4. Should the powershaft require shortening:

a. Hold the half-shafts next to each other in the

shortest working position and mark them.

b. Shorten inner and outer guard tubes equally.

c. Shorten inner and outer sliding profiles by the

same length as the guard tubes.

d. Proper overlap is a minimum of one-half the

length of each tube, with both tubes being of

equal length.

e. Round off all sharp edges and remove burrs.

Grease sliding profiles.

CAUTION! TRACTOR PTO SHIELD AND ALL MOWER GUARDS MUST BE IN

PLACE AT ALL TIMES DURING OPERATION!

The 3-point hitch system on this mower has been de-

signed for front to back flotation when mowing on un-

even terrain. The lower 3-point hitch blocks also are

adjustablefromfrontto backforadditionalfieldfloatand

tractor clearance. The lower hitch blocks have a large

pivot pin and a smaller locking pin, page 14 (#4) & (#5).

When operating a mower equipped with four gauge

wheels do not use lock pin (#4) unless desired for trans-

port.

The mower can be operated with hitch blocks in either

position. Depending upon the use of front gauge

wheels, the lower hitch blocks can be used without the

locking pin. If mower is not equipped with front gauge

wheels and leveling chains are used, the locking pin

should be installed. The lower hitch blocks and top link

rear braces can be adjusted front to back as shown in

fig. 1. Fig. 1

GRASS CHUTE ASSEMBLY -

Refer to the parts illustration on page 14:

1. Loosen upper pivot bolt (#9) and remove lower

thumb screw (#17).

2. Hinge chute down and install thumb screw and flat

washer (#13) and (#17). When set at position desired,

tighten down upper pivot bolt and lock nut (#9) and

(#10). DO NOT tighten completely. Allow chute to

hinge. Lock down lower thumb screw with flat washer

(#13) and (#17).

DO NOT in any condition operate mower with chute

removed from this position.

10479

POWERSHAFT INSTALLATION

TRACTOR HOOK-UP

FLOATING AND FRONT TO BACK HITCH ADJUSTMENTS

ASSEMBLY INSTRUCTIONS (CON’T.)

1/29/04

LEVELING THE MOWER

THREE AND FOUR GAUGE WHEELS

FRONT TO REAR:

NOTE: Tractor and mower should be on level ground.

1. Set the lower hitches and upper floating hitch as

shown in fig. 1 on page 5.

2. Start tractor and raise mower, watching that tractor

draw bar (if not removed) does not interfere with mower.

3. Slowly lower mower until gauge wheels touch the

ground and with mower deck close to level.

4. Setpartbrake andturn off tractor. Removekey from

ignition.

5. Rotate mower blades parallel to direction of travel.

Measurecutting edgetoground clearanceon each side

of the mower.

6. Measure the clearance from the cutting edge to the

ground at front and rear of the blade. This measure-

ment should be equal or have the blade at the front of

the mower not more than 1/2" lower than the blade at

the rear of the mower.

7. Use tractor 3-point top link to level the blade front to

back. Set tractor control when level.

8. Adjust lift chains to be tight by placing chains into

slots on lower chain brackets. Be sure to connect the

same link on both sides. Install plastic plugs. Secure

excess chain links together with the two tie straps in-

cluded.

SIDE TO SIDE:

1. Set lower hitches and upper floating hitch at desired

setting as shown in fig. 1 on page 5.

2. Start tractor and raise mower, watching that tractor

draw bar (if not removed) does not interfere with mower.

3. Slowlylowerthemoweruntilgaugewheelstouchthe

ground.

4. Set park brake and turn off tractor.

5. With discharge chute hinged out of the way, rotate

blade 90 degrees to direction of travel. If unequal, ad-

just one lower lift link of tractor 3-point hitch to level

mower.

6. Adjust lift chains to be tight by placing chains into

slots on lower chain brackets. Be sure to connect the

same link on both sides. Install chain connector. Se-

cure excess chain links together with the two tie straps

included.

NOTE: Tractor and mower should be on level ground.

1. Set lower hitches and upper floating hitch, as shown

in fig. 1 on page 5.

2. Start tractor and raise mower, watching that tractor

draw bar (if not removed) does not interfere with mower.

3. Slowlylowerthemoweruntilgaugewheelstouchthe

ground and the lower mower 3-point hitch bars are par-

allel to the ground in floating position. Set tractor 3-

point stop.

4. Set park brake and turn off tractor. Remove key

from ignition.

5. Adjust thetractor top link in or out to place the upper

hitchpin verticallyabove thelower hitchpin as shownin

fig. 1 on page 5, to allow mower flotation.

6. Rotate blades parallel to direction of travel.

7. Measure the clearance from the cutting edge to the

ground at front and rear of the blade. This measure-

ment should be equal or have the blade at the front of

the mower not more than 1/2" lower than the blade at

the rear of the mower.

TWO REAR GAUGE WHEELS IN REAR AND SUPPORT CHAINS

1/29/04

1. Usingthetractor, raisethemower off thegroundand

support under it with secure blocking so not to let the

mower drift down during maintenance.

2. Holding wheel and yokeassembly up, remove quick-

lock pin from top of gauge wheel spindle. Position full

length spacers and half spacer as required. All spacers

on top of spindle tube allows for approximately 1" cut-

ting height. Adjustments range from 1" to a maximum of

5 1/2" in 1/2" increments. Refer to "Leveling Mower" on

page 6.

NOTE: If equipped with only rear gage wheels, the

mower must be leveled front to rear each time this ad-

justment is made.

CAUTION! ENGAGE PARKING BRAKE, SHUT OFF TRACTOR, REMOVE KEY

AND DISENGAGE PTO BEFORE MAKING ANY HEIGHT ADJUSTMENTS!

IMPORTANT: Always disengage PTO before rais-

ing the mower to transport position.

1. When raising the mower to the transport position, be

surethat powershaft doesnotcontact tractorormower.

Adjust the tractor’s 3-point hitch lift height so that the

PTO shaft does not contact mower deck.

2. Be sure to reduce tractor ground speed when turn-

ing; and, leave enough clearance so the mower does

not contact obstacles such as buildings, trees or fences.

3. Select a safe ground travel speed when transporting

fromone areato another. Whentravelingon roadways,

transport in such a way that faster moving vehicles may

pass you safely.

4. When traveling over rough or hilly terrain, shift trac-

tor to a lower gear.

1. Clear the area to be mowed of objects and debris

that might be picked up and thrown by the mower

blades.

2. Grass is best cut when it is dry. Mowing wet grass

cancausepluggingresultingingrassclumpsbehindthe

mower.

3. Grass should be mowed frequently as shorter clip-

pings deteriorate faster.

4. If mowing extremely tall grass, it is best to raise

5. cutting height and mow the area, then lower cutting

height and mow a second time at the desired height.

6. Thismower isequipped withan adjustablegrass dis-

charge chute. Adjustments can be made by loosening

the bolts on the front and rear of mower chute. With the

mower chute in the raised operating position, grass is

expelled away from the mower for a more even distribu-

tion of grass clippings. Lowering the mower chute will

decrease the distance the grass is discharged from the

mower.

CAUTION! WHEN MOWING IN SANDY SOIL AREAS, WEAR MAY OCCUR TO

YOUR MOWER BLADES CAUSED FROM SAND EROSION. FREQUENT INSPECTION

SHOULD BE MADE AND BLADES REPLACED IF DAMAGED.

CAUTION! WHEN TRAVELING ON PUBLIC ROADS, WHETHER AT NIGHT OR

DURING THE DAY, USE ACCESSORY LIGHTS AND DEVICES FOR ADEQUATE WARNING

TO OPERATORS OF OTHER VEHICLES. COMPLY WITH ALL FEDERAL, STATE, AND

LOCAL LAWS.

CUTTING HEIGHT ADJUSTMENT

TRANSPORTING

MOWING INSTRUCTIONS AND ADJUSTMENTS

1/29/04

OPERATING INSTRUCTIONS

BEFORE beginning to mow, the following inspection should be performed:

Proper servicing and adjustments is the key to the long

life of any machine. With careful and systematic inspec-

tion of the mower, you can avoid costly maintenance,

time and repair.

For Safety reasons, each maintenance opera-

tion must be performed with the tractor’s PTO dis-

engaged, the mower lowered completely, tractor

engine shut off and ignition key removed.

SERVICE DAILY:

1. Grease the PTO u-joint.

2. Check that all bolts are tight.

LUBRICATE EVERY 50 HOURS OF OPERATION:

1. With the mower on level ground, check the oil level

in the gearbox by removing the plug in the side of the

box. The oil should reach the plug hole. Fill if neces-

sary with SAE 90 oil and retighten both plugs. DO NOT

OVERFILL! Should your gearbox require service, take

it to your LAND PRIDE dealer.

IMPORTANT: Mower should be level when check-

ing or adding oil to the gearbox!

BLADE SPINDLES........................................Greasable

HITCH....................................................Cat. 1 Floating

Clevis

GAUGE WHEELS:..........................................Castered

1 REAR 2 FRONT 10 1/4 x 3 1/4

Solid Tire

GAUGE WHEELS:..........................................Castered

2 REAR 2 FRONT 10 1/4 x 3 1/4

OPTIONAL Solid Tire

CASTER WHEEL...............................1" Diameter With

SPINDLE Greasable Bushing

DRIVE TRAIN ........................................540 RPM PTO

Gearbox

2.5:1 Ratio

Beveled Gears

Cast Iron Housing

Single V-Belt

GRASS CHUTE...............................Hinged-Adjustable

CUTTING WIDTH ....................................................48"

OVERALL WIDTH..............................................58 1/2"

HEIGHT ...................................................................36"

LENGTH (4 WHEEL) ...............................................56"

WEIGHT................................................................ 399#

CUTTING HEIGHT...........................................1"-5 1/2"

1/2" Increments

DECK MATERIAL..........................................10 Gauge

THICKNESS

BLADES - 2................................1/4" X 2 1/2" X 24 7/8"

Heat Treated

Alloy Steel

BLADE OVERLAP ...............................................1 1/2"

BLADE TIP SPEED ....................................15,745FPM

1. Check oil level in gearbox. Refer to "Maintenance"

& "Lubrication" on page 9 of this manual.

2. Check that all plugs in gearbox have been replaced

and tightened properly.

3. Be sure all mower blades, bolts and nuts are tight.

4. Be certain all guards and shieldsare in place and se-

cure.

5. Grease PTO shaft and all other grease fittings.

6. Clear the area to be mowed of rocks, branches and

other foreign objects.

7. Lower mower to ground. Set tractor throttle at ap-

proximately 1/4 open. Engage PTO to start blades ro-

tating.

8. Operate with 540 rpm PTO tractor.

9. At first begin mowing at a slow forward speed and

shiftupuntilthe desiredspeed is achieved- maintaining

540 PTO rpm.

10. Mower blades will cut better at a faster blade speed

than at reduced throttle.

11. Mowing should not be done in wet conditions as

grass will stick to blades and the under side of mower

deck.

12. Aftermowing thefirst 50feet,stop andcheck to see

that the mower is adjusted properly.

13. DO NOT make sharp turns or attempt to back up

while mower is on the ground.

14. DO NOT engagePTO withmowerin thefully raised

position. DO NOT engage PTO at full throttle.

OPERATING CHECK LIST

SPECIFICATIONS

1/29/04

V-BELT INSTALLATION -

1. Remove belt covers.

2. Move belt take-up handle in a clockwise direction to

relieve tension on belt.

3. With tension relieved from belt remove old belt from

pulleys.

4. Install new belt referring to the figure below (also re-

fer to the decal on top of mower deck). Be sure belt is

positioned in all the pulley grooves. Release belt take-

up handle to apply tension to new belt.

5. Reinstall all belt covers and secure in place with

hardware.

Proper servicing and adjustments is the key to the long life of any machine. With careful and systematic inspection

of the Grooming Mower, you can avoid costly maintenance, time and repair.

BLADE REPLACEMENT -

IMPORTANT: ALWAYS install blade with cutting edge

facing direction of rotor shaft rotation.

1. Remove cap screw and blade washer from blade to

be replaced. Remove blade.

2. Install blade washer into center hole on blade.

3. Replace cap screw and lock washer and tighten

bolts to proper torque. See "Nut & Bolt Torquing Chart"

on page 4.

IMPORTANT: Replace blades with genuine Land

Pride blades only.

BLADE SHARPENING -

1. Blades should be sharpened at each end to the

same angle as the original cutting edge.

NOTE: Care should be taken in order not to remove

any more material than necessary to sharpen blade.

2. Balance each blade after sharpening.

SERVICE DAILY:

1. Grease the PTO u-joints.

2. Wheel support bushings.

3. Wheel bushing.

4. Bearing in blade spindle hubs.

NOTE: There is a small relief hole on each spindle hub

casting on the underside of the deck. The relief hole re-

leases pressure from inside the spindle hub casting

when being greased. Spindle hubs should be greased

until grease purges from relief hole.

SERVICE EVERY 50 HOURS OF OPERATION:

1. With the mower on level ground, check the oil level

in the gearbox by removing the plug in the side of the

box. The oil should reach the plug hole. If oil level is

low, remove the top plug in the gearcase and fill with

SAE 90 oil until oil flows from side port of the gearbox.

Reinstall plugs and retighten. DO NOT OVERFILL!

Should your gearbox require service, take it to your

LAND PRIDE dealer.

IMPORTANT: Mower should be level when check-

ing oil in gearbox!

2. Disconnect PTO shaft from the tractor and slide

apart. Clean and coat the inner tube of the PTO shaft

with a light film of grease and then reassemble.

LUBRICATION

CAUTION! BELT DRIVE SYSTEM

UNDER SPRING TENSION; USE CARE TO

AVOID BODILY HARM!

MAINTENANCE

For SAFETY REASONS, each maintenance operation must be performed with the tractor’s PTO dis-

engaged, the Mower lowered completely to the ground or on safely supported blocking, tractor engine shut

off and ignition key removed.

Table des matières

Autres manuels Land Pride Tondeuse à gazon

Land Pride

Land Pride RC50 Series Manuel utilisateur

Land Pride

Land Pride Rotary Cutter RCR2684 Manuel utilisateur

Land Pride

Land Pride ZXT54 Series Manuel utilisateur

Land Pride

Land Pride RCM5020 Series Manuel utilisateur

Land Pride

Land Pride DM3705 Series Manuel utilisateur

Land Pride

Land Pride 357-398M Manuel utilisateur

Land Pride

Land Pride AFM40200 Manuel utilisateur

Land Pride

Land Pride RCP2660 Manuel utilisateur

Land Pride

Land Pride AFM4016 Manuel utilisateur

Land Pride

Land Pride FDR1648 Series Manuel utilisateur

Land Pride

Land Pride ACCU-Z ZT60i Manuel utilisateur

Land Pride

Land Pride AFM4522 Manuel utilisateur

Land Pride

Land Pride 357-044M Manuel utilisateur

Land Pride

Land Pride FM2548 Manuel utilisateur

Land Pride

Land Pride ZT60 Manuel utilisateur

Land Pride

Land Pride AFM4214 Series Manuel utilisateur

Land Pride

Land Pride ACCU-Z ZT60i Manuel utilisateur

Land Pride

Land Pride AFM4014 Manuel utilisateur

Land Pride

Land Pride Accu-Z Razor ZSR54 Manuel utilisateur

Land Pride

Land Pride FM3188 Manuel utilisateur

Land Pride

Land Pride FDR2572 Manuel utilisateur

Land Pride

Land Pride at 2560 Manuel utilisateur

Land Pride

Land Pride ZXT60 Manuel utilisateur

Land Pride

Land Pride Accu Z ZT60 Series Manuel utilisateur

Manuels Tondeuse à gazon populaires d'autres marques

RHINO

RHINO 1958 Manuel utilisateur

Wolf Garten

Wolf Garten Compact plus 40 B Manuel utilisateur

Cub Cadet

Cub Cadet LTX 1045 Manuel utilisateur

Craftsman

Craftsman 917.378461 Manuel utilisateur

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manuel utilisateur

Challenge

Challenge CH18V2 Instructions de fonctionnement

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manuel utilisateur

DEWEZE

DEWEZE ATM-725 Manuel d'utilisation

Weed Eater

Weed Eater 180083 Manuel utilisateur

Husqvarna

Husqvarna Poulan Pro PP185A42 Manuel utilisateur

Better Outdoor Products

Better Outdoor Products Quick Series Manuel utilisateur

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manuel d'utilisation

MTD

MTD 795, 792, 791, 790 Manuel utilisateur

Toro

Toro Groundsmaster 3505-D Manuel utilisateur

Dennis

Dennis FT 610 Manuel utilisateur

AIRFORCE

AIRFORCE F-15 Gen 3 Manuel utilisateur

MTD

MTD 126-220-000 Manuel utilisateur

Toro

Toro 74806 Manuel utilisateur