Laguna Tools PRO SERIES Manuel utilisateur

THRIVING ON INNOVATION

Pro Series 4, 6 & 9 Panelsaw Manual

17101 Murphy Avenue, Irvine, CA 92614 www.lagunatools.com 800.234.1976

Dear Woodworker:

Thank you for your purchase and welcome to the Laguna Tools group of

discriminating woodworkers. I understand that you have a choice of

where to purchase your machines and appreciate the confidence you

have in our products.

Every machine sold by Laguna Tools has been carefully designed and

well thought through from a woodworker’s perspective. I cut on our

bandsaws, lathes, table saws and combination machines. Through my

hands-on experience, I work hard to make our machines better. I

strive to give you machines that inspire you to create works of art.

Machines that are a joy to run and work on. Machines that encourage

your performance.

Today, we offer high-performance machines with innovative solutions

that meet the needs of woodworkers and their ever-evolving craft.

I started Laguna Tools as a woodworker; I still am.

Thank you again for becoming a Laguna Tools customer.

Torben Helshoj

President and Founder - Laguna Tools

Thriving on Innovation

Table of contents

Page number

Safety Rules 4

Limited warranty 5

Noise emission 6

Specification sheet 7

Receiving your machine 8

Introduction to Table Saws 8

Parts of the Table Saw 9

Where to locate your machine 11

Unpacking your machine 11

Assembly and setup 14

Using and adjusting the machine 31

Maintenance and troubleshooting 34

Electrical drawing 43

Exploded view drawings and parts lists 46

Safety Rules

As with all machinery there are certain hazards involved with the

operation and use. Using it with caution will considerably lessen the

possibility of personal injury. However, if normal safety precautions are

overlooked or ignored, personal injury to the operator may result. If you

have any questions relative to the installation and operation, do not use the

equipment until you have contacted your supplying distributor.

Read the following carefully before operating the machine:

1. Keep the working area clean and be sure adequate lighting is

available.

2. Do not wear loose clothing, gloves, bracelets, necklaces or

ornaments. Wear face, eye, respiratory and body protection devices

as indicated for the operation or environment.

3. Be sure that the power is disconnected from the machine before tools

are serviced or an attachment is to be fitted or removed.

4. Never leave the machine with the power on.

5. Do not use dull, gummy or cracked cutting tools.

6. Be sure that the keys and adjusting wrenches have been removed

and all the nuts and bolts are secured.

Limited Warranty

New woodworking machines sold by Laguna Tools carry a one-year warranty

from the date of shipping. Laguna Tools guarantees all new machines sold to be

free of manufacturers’ defective workmanship, parts, and materials.

We will repair or replace, without charge, any parts determined by Laguna

Tools, Inc. to be a manufacturer's defect. We require the defective item/part to

be returned to Laguna Tools. In the event the item/part is determined to be

damaged due to lack of maintenance, cleaning or misuse/abuse, the customer

will be responsible for the cost to replace the item/part, plus all related shipping

charges.

This limited warranty does not apply to natural disasters, acts of

terrorism, normal wear and tear, product failure due to lack of maintenance or

cleaning, damage caused by accident, neglect, lack of or inadequate dust

collection, or misuse/abuse or damage caused when repair or alterations have

been made or attempted by others.

Laguna Tools, Inc. is not responsible for additional tools or modifications sold

or performed (other than from/by Laguna Tools, Inc.) on any Laguna Tools,

Inc. woodworking machine. Warranty may be voided upon the addition of such

noted tools and/or modifications, determined on a case-by-case basis.

Normal user alignment, adjustment, tuning and machine settings are not

covered by this warranty. It is the responsibility of the user to understand

basic woodworking machinery settings and procedures and to properly

maintain the equipment in accordance with the standards provided by the

manufacturer.

Parts, under warranty, are shipped at Laguna Tools, Inc's cost either by

common carrier, FedEx Ground service or a similar method.

Technical support to install replacement parts is primarily provided by phone,

fax, or e-mail. The labor required to install replacement parts is the

responsibility of the user.

Laguna Tools is not responsible for damage or loss caused by a freight

company or other circumstances not in our control.

Only new machines sold to the original owner are covered by this warranty.

For warranty repair information, call 1-800-332-4094.

Noise emission.

Notes concerning noise emission:

Given that there exists a relationship between noise level and exposure times, it

is not precise enough to determine the need for supplementary precautions. The

factors affecting the true level of exposure to operators are clearly the amount

of time exposed, the characteristics of the working environment, other sources

of dust and noise, etc. For example, adjacent machines, in other words, the level

of ambient noise. It is possible that exposure level limits will vary from country

to country.

Note:- When using a scoring blade, the

machine will only accept a 10” main blade

Specification sheet.

Note:- The first part of this manual covers the Pro Sliding

Tablesaw [4 foot]. The Pro Series 6ft & 9ft Sliding are covered at

the end of the manual.

Machine Sliding table saw 6’ sliding panel

saw 9’ sliding panel

saw

Blade 10” or 12” 10” or 12” 10” or 12”

Dado capacity 13/16” 13/16” 13/16”

Main motor 3 hp220V single

phase 4hp220V single

phase

Electrical cable Yes Yes Yes

Cast-iron [ground]

table size 32” X 20” 32” X 20” 32” X 20”

Table height 34” 34” 34”

Weight Shipping/

Net 1250 / 1100lb 1350 / 1200 lb 1600 / 1400 lb

Dust port 4” 4” 4”

Blade guard Yes Yes Yes

Scoring blade

diameter 120mm X 22mm 120mm X 22mm 120mm X 22mm

Scoring motor ¾ hp ¾ hp ¾ hp

Main blade speed 4500 rpm 4500 rpm 4500 rpm

Scoring blade speed 6500 rpm 6500 rpm 6500 rpm

Rip capacity 50” 50” 50”

Sliding table

dimensions 47” X 14” 63” X 14” 106” X 142

Cross-cut capacity 51” 73” 116”

Cutting height 90/45

deg with scoring 3 ½” / 2 1/8” 3 ½” / 2 1/8” 3 ½” / 2 1/8”

Cutting height 90/45

deg. with out scoring 4” / 2 ¾” 4” / 2 ¾” 4” / 2 ¾”

Receiving your machine.

Note: It is probable that your machine will be delivered by a third party. Before

you unpack your new machine, you will need to first inspect the packing,

invoice and shipping documents supplied by the driver.

Insure that there is no visible damage to the packing or the machine. You need

to do this prior to the driver leaving. All damage must be noted on the delivery

documents and signed by you and the delivery driver. You must then contact

the seller [Laguna Tools] within 24.

Introduction to Table Saws.

This Table Saw is designed to give you years of safe service. Read this owner’s

manual in its entirety before assembly or use.

Parts of the Table Saw.

The major parts are discussed in this manual. If you are not familiar with the

table saw take the time to read this section and become familiar with the

machine.

1. Body.

2. Dust collection port.

3. Angle adjustment handle.

4. Table.

5. Guard.

6. Fence.

7. Extension table.

8. Emergency stop button.

9. Blade height adjustment handle.

10. Electrical box and on/off switches.

11. Clamp.

12. Support table.

13. Sliding table.

14. Miter fence.

Identification.

There is a plate at the back of the machine listing all the manufacturing data

including the serial number, model, etc.

Cabinet / Body.

The cabinet has a large footprint and is of welded construction manufactured

from heavy gauge steel plate. The cabinet houses all the parts of the machine

and the heavy construction ensures that the saw is stable. This weight also helps

to absorb any vibration that is produced during cutting.

Table.

The table is manufactured from cast iron. The table is attached to the cabinet.

The table is adjustable for being level and vertical.

Extension table.

An extension table is provided to increase the range of jobs that can be

produced.

Autres manuels pour PRO SERIES

Table des matières

Autres manuels Laguna Tools Outils électriques

Laguna Tools

Laguna Tools DAKE 4 Manuel utilisateur

Laguna Tools

Laguna Tools RPM5 Manuel utilisateur

Laguna Tools

Laguna Tools DAKE 33-493 Manuel utilisateur

Laguna Tools

Laguna Tools MJO6405-0800 Manuel utilisateur

Laguna Tools

Laguna Tools DAKE 75H Manuel d'utilisation et d'entretien

Laguna Tools

Laguna Tools DAKE Force 25DA Manuel d'utilisation et d'entretien

Laguna Tools

Laguna Tools SHEARTEC II Manuel utilisateur

Laguna Tools

Laguna Tools DAKE 0 Manuel utilisateur

Laguna Tools

Laguna Tools DAKE 1-1/2 Manuel d'utilisation et d'entretien

Laguna Tools

Laguna Tools P12 10 Manuel utilisateur

Laguna Tools

Laguna Tools DAKE 33-672 Manuel utilisateur

Laguna Tools

Laguna Tools Platinum Series Manuel utilisateur

Laguna Tools

Laguna Tools DAKE 1 Manuel utilisateur

Laguna Tools

Laguna Tools P12 5 Manuel utilisateur

Laguna Tools

Laguna Tools DAKE X Manuel utilisateur

Laguna Tools

Laguna Tools DAKE 5 Manuel utilisateur

Laguna Tools

Laguna Tools DAKE Force 50DA Manuel d'utilisation et d'entretien

Laguna Tools

Laguna Tools DAKE 1-1/2C Manuel d'utilisation et d'entretien

Laguna Tools

Laguna Tools DAKE Force 10DA Manuel d'utilisation et d'entretien

Laguna Tools

Laguna Tools DAKE 150H Manuel utilisateur

Laguna Tools

Laguna Tools JX6 Manuel utilisateur

Laguna Tools

Laguna Tools Dake 972200 Manuel d'utilisation et d'entretien

Laguna Tools

Laguna Tools PP16 XC Pro Manuel utilisateur

Laguna Tools

Laguna Tools DAKE SB-25V Manuel d'utilisation et d'entretien

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel