LabJack U12 Manuel utilisateur
LabJack U12 Quickstart Guide
Revision 1.09
9/8/2003
LabJack Corporation
www.labjack.com
For the complete LabJack U12 User’s Guide or the latest version of the LabJack software, go to
www.labjack.com.
The LabJack U12 is a measurement and automation peripheral that enables the connection of a
PC to the real world. Although the LabJack U12 has many redundant protection mechanisms, it
is possible, in the case of improper and/or unreasonable use, to damage the LabJack and even
the PC to which it is connected. LabJack Corporation will not be liable for any such damage.
Installation
The LabJack U12 requires a PC running Windows 98SE, ME, 2000, or XP. To determine your
operating system version, go to
Start => Settings => Control Panel => System => General
and make sure the version number is 4.10.2222 or higher (Win98SE=4.10.2222,
WinME=4.90.3000, Win2000=5.0.2195, WinXP=5.1.XXXX).
It does not matter if the hardware or software is installed first.
If you experience installation problems on Windows 98 Second Edition, before contacting us,
please go to the downloads page at labjack.com and download “win98sehid.zip” (see the
readme file for more information).
Hardware Installation
With the PC on and using the included cable, connect the LabJack U12 to the USB port on the
PC or USB hub. The USB cable provides power and communication for the LabJack U12. The
status LED should immediately blink 4 times (at about 4 Hz), and then stay off while the
LabJack enumerates.
Enumeration is the process where the PC’s operating system gathers information from a USB
device that describes it and it’s capabilities. The low-level drivers for the LabJack U12 come
with Windows and enumeration will proceed automatically. The first time a device is
enumerated on a particular PC, it can take a minute or two, and Windows might prompt you
about installing drivers. Accept all the defaults at the Windows prompts, and reboot the PC if
asked to do so. The Windows Installation CD might also be needed at this point. Make sure a
CD with the correct version of Windows is provided. Enumeration occurs whenever the USB
cable is connected, and only takes a few seconds after the first time.
When enumeration is complete, the LED will blink twice and remain on. This means Windows
has enumerated the LabJack properly.
If the LabJack fails to enumerate:
• Make sure you are running Windows OS version 4.10.2222 or higher,
• If Win98SE, check out win98sehid.zip from our downloads page,
• Try connecting the LabJack to another PC,
• Try connecting a different USB device to the PC,
• Check our online forum and/or contact LabJack.
Software Installation
Although, the low-level USB drivers for the LabJack are included with Windows, high-level
drivers are needed to send and receive data. The included LabJack CD installs the high-level
drivers, example source code, and example applications.
Close all open applications, especially LabJack related software, and insert the LabJack CD. If
autorun is enabled, the installation program should start automatically. If the installation does
not start, you will have to manually double-click on LabJackVXXX.exe.
When the LabJack installation is finished, it will start the National Instruments LabVIEW Run-
Time Engine (LVRTE) setup. The LVRTE is required for the example applications, such as
LJtest. If prompted to reboot after this installation, go ahead and do so. Virus scanners can
often interfere with the installation of the LVRTE. If you have trouble running the example
applications, repeat the LabJack software installation to make sure the LVRTE is installed.
To test the installation, start LJtest by selecting
Start => Programs => LabJack => LJtest.
Make sure “Test Fixture Installed” and “Continuous” are not selected, and press the “Run”
button. LJtest should step through and pass 8 separate tests.
Hardware Description
The external features of the LabJack U12 are:
• USB connector
• DB25 digital I/O connector (D lines)
• Status LED
• 30 screw terminals.
The USB connection provides power and communication. No external power supply is needed.
The +5 volt connections available at various locations are outputs, do not connect a power
supply.
Figure 1. LabJack U12 top surface.
Figure 1 shows the top surface of the LabJack U12. Not shown are the USB and DB25
connectors, which are both on the top edge. The DB25 connector provides connections for 16
digital I/O lines, called D0-D15. It also has connections for ground and +5 volts. All
connections besides D0-D15, are provided by the 30 screw terminals shown in Figure 1. Each
individual screw terminal has a label, AI0 through STB.
• AI0 – AI7: The LabJack U12 has 8 screw terminals for analog input signals. These can be
configured individually and on-the-fly as 8 single-ended channels, 4 differential channels, or
combinations in between. Each input has a 12-bit resolution and an input bias current of ±90 µA.
o Single-Ended: The input range for a single ended measurement is ±10 volts.
o Differential channels can make use of the PGA to provide gains up to 20, giving an
effective resolution greater than 16-bits. In differential mode, the voltage of each AI with
respect to ground must be between ±10 volts, but the range of voltage difference
between the 2 AI is a function of gain (G) as follows:
G=1 ±20 volts
G=2 ±10 volts
G=4 ±5 volts
G=5 ±4 volts
G=8 ±2.5 volts
G=10 ±2 volts
G=16 ±1.25 volts
G=20 ±1 volt
• AO0 & AO1: The LabJack U12 has 2 screw terminals for analog output voltages. Each analog
output can be set to a voltage between 0 and the supply voltage (+5 volts nominal) with 10-bits of
resolution.
• IO0 – IO3: Connections to 4 of the LabJack’s 20 digital I/O are made at the screw terminals, and
are referred to as IO0-IO3. These 4 channels include a 1.5 k Ω series resistor that provides
overvoltage/short-circuit protection.
• D0 – D15: Connections to 16 of the LabJack’s 20 digital I/O are made at the DB25 connector,
and are referred to as D0-D15. These 16 lines have no overvoltage/short-circuit protection, and
can sink or source up to 25 mA each (total sink or source current of 200 mA max for all 16). All
digital I/O are CMOS output and TTL input except for D13-D15, which are Schmitt trigger input.
DB25 Pinouts:
1: D0 6: D5 11: +5V 16: GND 21: D11
2: D1 7: D6 12: +5V 17: GND 22: D12
3: D2 8: D7 13: +5V 18: D8 23: D13
4: D3 9: NC 14: GND 19: D9 24: D14
5: D4 10: +5V 15: GND 20: D10 25: D15
• CNT: The input connection to the 32-bit counter is made at screw-terminal CNT. The counter is
incremented when it detects a falling edge followed by a rising edge, and is capable of counting
frequencies up to at least 1 MHz.
• CAL & STB: These terminals are used during testing and calibration. The CAL terminal is a 2.5
volt reference.
• +5V: The LabJack has a nominal +5 volt internal power supply. Power can be drawn from this
power supply by connecting to the +5V screw-terminals, or the +5V pins on the DB25 connector.
The total amount of current that can be drawn from the +5V pins, analog outputs, and digital
outputs, is 450 mA for most desktop computers and self-powered USB hubs. Some notebook
computers and bus-powered hubs will limit this available current to about 50 mA.
• GND: The GND connections available at the screw-terminals and DB25 connector provide a
common ground for all LabJack functions.
LabJack Operation
The LabJack U12 CD installs 9 example applications: LJconfig, LJcounter, LJfg, LJlogger,
LJscope, LJstream, LJtest, LJSHT, and LJSHTmulti. The LabVIEW source code for most of
these is installed in the examples directory.
Also installed are high-level drivers (ljackuw.dll), an ActiveX interface to the high-level drivers
(ljackuwx.ocx), and LabVIEW VIs which call all the DLL functions. The DLL and OCX are
installed in the Windows System directory. If the installation program can determine the
LabVIEW directory, it copies the LabVIEW drivers into that directory (\vi.lib\addons\) so they
show up on the function palette. Otherwise, the LabVIEW drivers are copied into the LabJack
installation directory (c:\Program Files\LabJack)\drivers\labview, and can manually be
transferred to the LabVIEW directory.
Example Applications
• LJconfig: Sets the local ID of a particular LabJack. This is useful if multiple LabJacks are
connected to the USB. Every LabJack has a local ID and serial number. The local ID is a value
between 0 and 255 that can be changed by the user. The serial number is a value between 256
and 2,147,483,647. The serial number is unique among all LabJacks and cannot be changed by
the user.
• LJcounter: Reads the LabJack counter and provides the frequency or count.
• LJfg: Outputs basic waveforms on AO0 (analog output zero).
• LJlogger: Sends and receives data from all channels in command/response mode.
• LJscope: Simulates an oscilloscope by reading data from 2 AI channels in burst mode.
• LJstream: Uses stream mode to read, graph, and write to file, 4 AI channels.
• LJtest: Runs a sequence of tests on the LabJack itself. Users will generally leave “Test Fixture
Installed” unselected and execute the tests with nothing connected to the LabJack (except the
USB of course).
• LJSHT: Retrieves and records data from 1 or 2 EI-1050 digital temperature/humidity probes.
• LJSHTmulti: Displays data from up to 20 EI-1050 digital temperature/humidity probes.
Drivers
There are 37 functions exported by the LabJack DLL., and matching functions in the OCX and
LabVIEW VIs. All functions are command/response except for AIBurst and
AIStreamStart/Read/Clear. Following is a brief description of each function. For more details
on each function see the LabJack U12 User’s Guide.
• EAnalogIn: Reads the voltage from one analog input.
• EAnalogOut: Sets the voltage on both analog outputs.
• ECount: Reads and resets the counter.
• EDigitalIn: Reads the state of one digital input.
• EDigitalOut: Sets the state of one digital output.
• AISample: Reads the voltages from 1,2, or 4 analog inputs. Also controls/reads the 4 IO ports.
• AIBurst: Reads a specified number of scans (up to 4096) at a specified scan rate (up to 8192
Hz) from 1,2, or 4 analog inputs. First, data is acquired and stored in the LabJack’s 4096 sample
RAM buffer. Then, the data is transferred to the PC.
• AIStreamStart: Starts a hardware timed continuous acquisition where data is sampled and
stored in the LabJack RAM buffer, and can be simultaneously transferred out of the RAM buffer
to the PC application. A call to this function should be followed by periodic calls to
AIStreamRead, and eventually a call to AIStreamClear.
• AIStreamRead: Waits for a specified number of scans to be available and reads them.
AIStreamStart should be called before this function and AIStreamClear should be called when
finished with the stream.
• AIStreamClear: This function stops the continuous acquisition. It should be called once when
finished with the stream.
• AOUpdate: Sets the voltages of the analog outputs. Also controls/reads all 20 digital I/O and the
counter.
• AsynchConfig: Configures the LabJack U12 D lines for asynchronous communication.
• Asynch: Writes then read half-duplex asynchronous data on 1 of two pairs of D lines. Basically
RS232 communication.
• BitsToVolts: Converts a 12-bit (0-4095) binary value into a LabJack voltage.
Volts=((2*Bits*Vmax/4096)-Vmax)/Gain where Vmax=10 for SE, 20 for Diff.
• VoltsToBits: Converts a voltage to it's 12-bit (0-4095) binary representation.
Bits=(4096*((Volts*Gain)+Vmax))/(2*Vmax)
• Counter: Controls and reads the counter. The counter is disabled if the watchdog timer is
enabled.
• DigitalIO: Reads and writes to all 20 digital I/O.
• GetDriverVersion: Returns the version number of ljackuw.dll.
• GetErrorString: Converts a LabJack errorcode, returned by another function, into a string
describing the error.
• GetFirmwareVersion: Retrieves the firmware version from the LabJack.
• GetWinVersion: Uses a Windows API function to get the OS version.
• ListAll: Searches the USB for all LabJacks, and returns the serial number and local ID for each.
• LocalID: Changes the local ID of a specified LabJack. Changes will not take effect until the
LabJack is re-enumerated or reset, either manually by disconnecting and reconnecting the USB
cable or by calling ReEnum or Reset.
• NoThread: Disables thread creation. Use with TestPoint on Windows 98/ME.
• PulseOut: Creates pulses on any/all of D0-D7.
• PulseOutStart: Starts a pulse output similar to PulseOut, but does not wait for it to finish.
• PulseOutFinish: Waits for the finish of a pulse output started with PulseOutStart.
• PulseOutCalc: Used to calculate cycle times for the pulse output functions.
• ReEnum: Causes the LabJack to electrically detach from and re-attach to the USB so it will re-
enumerate. The local ID and calibration constants are updated at this time.
• Reset or ResetLJ: Causes the LabJack to reset after about 2 seconds. After resetting the
LabJack will re-enumerate.
• SHT1X: Retrieves temperature and/or humidity readings from an SHT1X sensor.
• SHTComm: Generic low-level function to send and receive up to 4 bytes to/from an SHT1X
sensor.
• SHTCRC: Checks the CRC on an SHT1X communication.
• Synch: Performs SPI communication with a slave device.
• Watchdog: Controls the LabJack watchdog function. When activated, the watchdog can change
the states of digital I/O if the LabJack does not successfully communicate with the PC within a
specified timeout period. This function could be used to reboot the PC allowing for reliable
unattended operation. The 32-bit counter (CNT) is disabled when the watchdog is enabled.
• ReadMem: Reads 4 bytes from a specified address in the LabJack's nonvolatile memory.
• WriteMem: Writes 4 bytes to the LabJack's 8,192 byte nonvolatile memory at a specified
address. The data is read back and verified after the write. Memory 0-511 is used for and
calibration data. Memory from 512-1023 is unused by the LabJack and available for the user
(this corresponds to starting addresses from 512-1020). Memory 1024-8191 is used as a data
buffer in hardware timed AI modes (burst and stream).
Warranty
The LabJack U12 comes with a 1 year limited warranty from LabJack Corporation (LC),
covering this product and parts against defects in material or workmanship. The LabJack can
be damaged by misconnection (such as connecting 120 VAC to any of the screw terminals),
and this warranty does not cover damage obviously caused by the customer. If you have a
the customer is responsible for shipping to LC, and LC will pay for the return shipping.
Declaration of Conformity
Manufacturers Name: LabJack Corporation
Manufacturers Address: 13701 W Jewell Ave, STE 284, Lakewood, CO 80228, USA
Declares that the product
Product Name: LabJack U12
Model Number: LJU12
conforms to the following Product Specifications:
EMC Directive: 89/336/EEC
EN 55011 Class A
EN 61326-1: General Requirements
EN 61000-4-2: 1995
EN 61000-4-3: 1995
and is marked with CE.
Autres manuels pour U12
3
Table des matières
Autres manuels LabJack Enregistreur de données
