Laars FT Series Manuel utilisateur

User's Manual

WARNING

If the information in this manual is not

result causing property damage, personal

injury or loss of life.

Do not store or use gasoline or other

this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

nearby phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call

Installation and service must be performed

supplier.

FOR YOUR SAFETY: This product must be installed and serviced by a professional service technician,

, property damage, or

death. Improper installation and/or operation will void the warranty.

AVERTISSEMENT

Assurez-vous de bien suivres les instructions

données dans cette notice pour réduire au

minimum le risque d’incendie ou d’explosion

ou pour éviter tout dommage matériel, toute

blessure ou la mort.

Ne pas entreposer ni utiliser d’essence ou ni

le à proximité de cet appareil ou de tout autre

appareil.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE

GAZ:

•Ne pas tenter d’allumer d’appareils.

• Ne touchez à aucun interrupteur. Ne pas vous servir

des téléphones dans lebâtiment où vous vous

trovez.

• Appelez immédiatement votre fournisseur de

gaz depuisun voisin. Suivez les instructions

du fournisseur.

•Si vousnepouvez rejoindre le fournisseur de

gaz, appelez le sservice des incendies.

L’installation et l’entretien doivent être assurés par

ou par le fournisseur degaz.

User's Manual for

•

•Propane Gas (LP) - Field-Convertible

Document

1511

Floor Standing, Modulating

Gas, Condensing,

Heating Only

Boiler

Model FTHF199N

199,000 BTU/h

H2420000-

1. Familiarizing yourself to

THE FT

The FT is a floor standing, condensing and

fully modulating, residential boiler.

This Users Manual will guide you into the basics

of operating your FT

Please reference the Installation and Operation

Manual for complete details ).

Page 2

CONTENTS Pgs -

1. Familiarizing yourself with the FT ..........................2

2. Caring For Your FT................................................4

3. Start Up and Shut Down. ......................................4

4. Control Display and Operation .........................5-10

Page 3

#Name of Component

1Pressure Relief Valve

2Air Vent (air eliminator)

3Boiler Return Connection

4Boiler Supply Connection

5Vent Pipe Collar

6Boiler Pressure Gauge

7Air Intake Collar

8Gas Inlet Adapter

9Air/ Gas Venturi

10 Gas Valve

11 BLDC Fan (Blower)

12 Low Water Cut O󰀨

13 Burner High Limit Switch

14 Flame Detecting Sensor

15 Manual Power Switch (ON / OFF)

16 Heat Exchanger

17 Main PCB

18 Boiler Pump

19 Blocked Condensate Switch

20 Condensate Trap

21 Condensate neutralizer and Drain pump

(optional equipment)

22 Drain Valve

23 Low Loss Header

24 Terminal Block

25 Overheat Temperature Sensor

26 Sight Glass

27 Igniter

28 Exhaust Pipe

29 Control Panel and Display

30 Air Pressure Sensor

1.1 Names of Components

User's Manual - The FT Series Floor Standing, Heating Only Boiler

Page 4

3. Shut Down and Restart

3.1 To Start the FT

If drained, please refer to the Install and

Operating Manual to ensure that the complete

‘Setup’ procedure has been followed before

starting this boiler. A complete ‘Setup’ must be

performed by a qualied service person.

3.2 Shutting Down the FT

1. Turn o󰀨 the main electrical disconnect switch.

2. Close all manual gas valves.

3. If freezing is anticipated, drain the FT and be

sure to also protect building piping from freezing.

All water must be removed from heat exchanger

and condensate trap or else damage from

freezing may occur. Please refer to the Install

and Operating Manual.

This step to be performed by a qualied service person.

2. Caring For Your FT

Your FT will require very little maintenance.

However, as with any ne appliance there are certain

steps that should be taken to ensure continuing

optimum performance.

2.1 General Care

Keep the area around the FT clean and free from

combustible materials, gasoline and other ammable

liquids and vapors.

The FT must be completely isolated and

protected from any source of corrosive chemical fumes

such as trichlorethylene, perchlorethylene, chlorine,

etc.

Keep bottom and top openings on the boiler free

for proper ventilation of interior components.

Do not obstruct or block a free ow of air to the

boiler to ensure proper ventilation.

If desired, clean the jacket surfaces with a

damp cloth and mild detergent. Do not use ammable

cleaning materials.

If sidewall vented, keep the vent terminal clear

of obstructions — do not allow snow to cover the vent

terminal. Clean the intake screen often, and then

develop an appropriate maintenance schedule.

2.2 Annual Inspection of Flue and Vents

Visually inspect the vent pipe once a year. Should

any deterioration exist, have the a󰀨ected parts replaced

by a qualied service person.

2.3 In the Event of a Power Failure

The FT can not be operated during an electrical

power outage. If there is an extended power outage with

danger from freezing, then the FT (and all other water

systems) should be drained completely. When draining

the boiler, turn o󰀨 main electrical disconnect switch.

When placing back in service, refer to Section 3 of this

Manual for instruction. All draining and lling must only

be done by a qualied service person.

2.4 Full Service Every Year

In addition to the annual visual inspections, a

qualied service agency should conduct a detailed

inspection of all ue product carrying areas of the boiler

and its venting system.

Page 5

4. The Control Display and Operation

Page 55

SECTION 5 Control Display and Operation

5.1 Control Dial and Buttons

• Temperature Speci cations

Operating ambient Temperature Range : -10 to 60°C.

Operating Relative Humidity up to: 90% at 40°C.

Shipping & Storage Temperature Range of : -20 to 80°C.

Buttons Functionality

PRESS (Tap) PRESS and HOLD (5 seconds)

A Display Power Turns Control Display ON / OFF

B Modes Tap to return to menu (If Display Power was On )

Status Display Mode

(If Display Power was O󰀨 )

Installer Mode

Heating

Water

CH set-point change mode

(Maxium 82

°C(180°F))

Time / Date

Set

No Change To SET: Year/Month/Week/Day/Time/Min

Scroll / Select

Menu select or value

up(+)/down(-) or setting dial.

The Control Display has a Control Dial (E), 4 buttons (A, B, C, D), and a Liquid

Crystal Display (with 72 back-lit segments). This section of this manual gives

instruction on how to navigate into the many functions of the FT and to change

temperature set points, set system variables and controller parameters.

Status Light

(constant green

when operating

normally)

WARNING

Do not use this appliance if any part has been under

water. Immediately call a quali ed service technician

to inspect the appliance and to replace any part of

the control system and any gas control that may have

been under water.

The Control Display

55page

User's Manual - The FT Series Floor Standing, Heating Only Boiler

Page 6

Page 56

5.2 LCD Overview

The LCD will illuminate when a user action is detected (a button is pressed) and will turn back o󰀨 after 20 seconds.

Symbol Name Description

Service Reminder mode Service Reminder mode indication

Outside Temperature Mode Outside Temp setting indication

Anti-freeze mode Anti-freeze mode indication

Storage mode Storage mode indication

Information mode Information mode indication

Communication state Communication state indication

Time setting mode Time /Dispaly/Install mode indication

Fan operating mode Fan operating mode indication

Flame signal Flame Signal indication

CH pump mode CH pump mode indication

Storage pump mode Storage pump mode indication

Internal boiler pump Internal Boiler pump mode indication

Celsius mode Indicated as Celsius temperature

Fahrenheit mode Indicated as Fahrenheit temperature

Heat demand mode Heat demand mode indication

DAY mode Current day mode indication

Cascade System connecting

mode

Cascade System connecting mode

indication

Cascade System operating mode Cascade System operating mode

indication

4. The Control Display and Operation (continued)

Page 7

The FT Series Heating Only, Boiler Page 57

5.3 Operating Mode

Operating Mode

After the Power is turned on, and/or the Control Display is turned on , the Control Display

will go through a ‘Start Up’ checklist and brie y show a sequence of diagnostic codes before

entering into the ‘Operating Mode. It will then display the following information.

The Control Display can operate through user and service modes that have speci c LCD output

and dedicated controls:

• Set-point change mode • Lock mode • Error mode • Status display mode

• Outside Temperature mode • Installer mode

* Control Display will not allow changing of button in case of lock mode activated.

Indicate Indicator

Current Operating Temperature Set-Point

If the Fan is operating

If a  ame is detected

Celsius or Fahrenheit or

Date and Time indicator

If Outside Temperature Sensor is operating

If there is a Demand for Central Heat (CH)

If CH pump state is

operating

If Internal recirculation pump is operating

If Communication state is activated

57page

User's Manual - The FT Series Floor Standing, Heating Only Boiler

Page 8

Page 58

The P-950EH Control Display does NOT have a daily timer or programmable thermostat.

Setting the Clock

a. Press and hold the ‘Clock button’ for about 5 seconds. Set the ‘Year’ by turning the dial E. And

then, press the dial E to Save.

b. Set the ‘MON’ (Month) by turning the dial E to the desired month number. Then press the dial E to Save.

c. Set the ‘DATE’ (1-31, Day of the Month) by turning the dial E. Then press the dial E to Save.

d. Set the ‘HOUR’ (1-24, Hour of the Day) by turning the dial E. Then press the dial E to Save.

e. Set the ‘MIN’ (1-60, Minute of the Hour) by turning the dial E. Then press the dial E to Save.

f. Set the ‘Day’ (Sun - Sat) by turning the dial E. Then press the dial E to Save.

To Exit at any time, tap the button.

5.4 Setting the Clock

57page

Page 9

The FT Series Heating Only, Boiler Page 59

5.5 CH Set Point Change Mode

CH Set point Change Mode

Indicate Indicator

Current CH Temperature Set-Point

Celsius or Fahrenheit or

If Communication state is activated

If  ame is detected

Date and Time indicator

If CH pump is operating

If there currently a Demand for Central Heat (CH)

Default CH set-point is 140°F (60°C)

CH set-point range is 130°F ~180°F (54°C ~ 82°C)

To change CH Setpoint, press the C button. The CH Icon and current

CH Setpoint will  ash.

Turn the E dial clockwise to increase, and counterclockwise to decrease CH setpoint, until

desired temperature is reached.

Press E dial to save changes and to Exit.

57page

User's Manual - The FT Series Floor Standing, Heating Only Boiler

Page 10

Page 60

5.6 Status Display Mode

Digital Display

Status Display Parameter

Description

O: ot Outdoor temperature Current outdoor sensor temperature

A: In 0-10 V display Current voltage of (0-10V input)

b: tt CH target temperature in cascade system Current CH target temperature or Current

System target temperature in a cascade system

C: It CH return water temperature Current CH return water temperature

d: Fr FAN speed ( rpm) Current FAN speed ( RPM)

E: oP CH supply temperature (Operating temperature) Current heating temperature

F: Eh Exhaust gas temperature Current exhaust gas temperature

H: dH

Indirect DHW tank temperature

* If temperature sensor is not connected

then it will display with 0°F (0°C).

Current DHW tank temperature

I: oH Overheat water temperature Current Overheat water temperature

L: rt

1: PH

Burner Operation

Time

Time for supply power

L: rt on display

on sub menu

Unit : 1000hour

2: rh Time for burner

operation Unit : 1hour

3: rH Time for burner

operation Unit : 1,000hour

4: It Cycle for ignition Cycle : 10 times the

displayed unit

5: IH Cycle for ignition Cycle : 10,000 times the

displayed unit

SELF Percentage of self units running. Percentage of self units running.

ALL Capacity for all operating

cascade units

Percentage of all cascade units running.

This screen shows the overal cascade power output. The

range of this value of boilers communicating with theMaster

x 100. For example, if 8 boilers are connected and

communicating, the maximum cascade power is 800%.

Range: 0-100%

F1 – F

19 Capacity for individual boilers Percentage of each cascade units running.

Ex. F1, F2, ….

N: St

System Temperature (cascade

mode) * If system temperature

sensor is not connected then it will

display with 0°F (0°C).

Current System Temperature (cascade mode)

NOTE: For Cascading

Installations, please refer to

document 1349 ‘Cascading

the FT Series Boiler’,

available online.

60page

To view any Status Parameter,

Press and Hold Button B to get into the Status Display Mode.

Rotate Dial E until you  nd the Parameter that you wish to view. Tap Dial E to enter that Parameter as

required. Dial E to save and to exit the Status Information Menu. To go back to the Operation Screen

Press button B.

Autres manuels pour FT Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Laars Chaudière

Laars

Laars Pennant PNCH Manuel utilisateur

Laars

Laars Horizon Manuel

Laars

Laars Mascot II Manuel utilisateur

Laars

Laars MINI-THERM JX Series Manuel utilisateur

Laars

Laars NEOTHERM NTH Manuel utilisateur

Laars

Laars FT Series Manuel utilisateur

Laars

Laars MINI-THERM JX Series Manuel utilisateur

Laars

Laars MFTCF140 Manuel utilisateur

Laars

Laars FTCF140 Manuel utilisateur

Laars

Laars OMNITHERM ONH1250 Manuel du propriétaire

Laars

Laars NTV1700 Manuel utilisateur

Laars

Laars Pennant PNCH Manuel utilisateur

Laars

Laars Mini-Therm JVi JVH Manuel utilisateur

Laars

Laars NTV Manuel utilisateur

Laars

Laars NEOTHERM NTV Manuel utilisateur

Laars

Laars MASCOT FT MFTCW Manuel utilisateur

Laars

Laars LMH Manuel utilisateur

Laars

Laars MagnaTherm MGH1600 Manuel utilisateur

Laars

Laars MIGHTYTHERM HH Mode d’emploi

Laars

Laars NEOTHERM NTH Manuel utilisateur

Laars

Laars LMH Manuel utilisateur

Laars

Laars FT Series Manuel utilisateur

Laars

Laars Mini-Therm JVH Manuel utilisateur

Laars

Laars Mighty Therm AP Manuel utilisateur

Manuels Chaudière populaires d'autres marques

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Manuel utilisateur

Radijator

Radijator BIO max 23.1 Manuel utilisateur

Brunner

Brunner BSV 20 Manuel utilisateur

Buderus

Buderus Logamax GB062-24 KDE H V2 Manuel utilisateur

Potterton

Potterton 50e Fiche technique

UTICA BOILERS

UTICA BOILERS TriFire Manuel utilisateur

Joannes

Joannes LADY Series Manuel

ECR International

ECR International UB90-125 Manuel d'instructions

Froling

Froling FHG Turbo 3000 Manuel utilisateur

Froling

Froling P4 Pellet 8 - 105 Manuel utilisateur

U.S. Boiler Company

U.S. Boiler Company K2 Manuel utilisateur

Henrad

Henrad C95 FF Manuel utilisateur

NeOvo

NeOvo EcoNox EF 36 Manuel utilisateur

Potterton

Potterton PROMAX SL 12 Manuel utilisateur

Eco Hometec

Eco Hometec EC 25 COMPACT Manuel utilisateur

Viessmann

Viessmann VITODENS 200 Mode d’emploi

Baxi

Baxi Prime 1.24 Manuel utilisateur

REXNOVA

REXNOVA ISA 20 BITHERMAL Manuel utilisateur