La Crosse Technology WS-8011UM Manuel utilisateur

attery

Cover

WS-8011UM with TX2U

433 MHz

Radio Controlled Temperature Clock

Pages 2 through 12

------------------------------------------------------------------------------------

WS-8011UM with TX5U

433 MHz

Radio Controlled Temperature Clock

Pages 14 through 26



Battery

Cover

WS-8011UM with TX2U

433 MHz

Radio Controlled Temperature Clock

Instruction Manual



Battery

Cover

TABLE OF CONTENTS

Topic Page

Inventory of Contents/ Additional Equipment 3

About WWVB 3

Quick Set-Up Guide 3

Detailed Set-Up Guide

Battery Installation 4

Program Mode

Function Buttons 5

Time Zone Setting 5

DST (Daylight Saving Time) Setting 6

Language Selection 6

Time Setting 6

Calendar Setting 7

12/24-Hour Setting 7

Selecting F or C 7

Features & Operations

Changing Display Mode (seconds, temperature) 7

The Alarm 8

Indoor Temperature 8

Remote Temperature 8

Mounting 9-10

Maintenance & Care 10

Troubleshooting 11

Specifications 11

Warranty Information 12

INVENTORY OF CONTENTS

1) WS-8011UM

2) TX2U Remote temperature transmitter

3) Instruction manual and warranty card.

ADDITIONAL EQUIPMENT (not included)

1) Two fresh 1.5V AA batteries.

2) Two fresh 1.5V AAA batteries.

3) Three wall-hanging screws.

4) Appropriate screwdriver for screws.

ABOUT WWVB (Radio Controlled Time)

The NIST (National Institute of Standards and Technology—Time and Frequency

Division) WWVB radio station is located in Ft. Collins, Colorado, and transmits the exact

time signal continuously throughout the United States at 60 kHz. The signal can be

received up to 2, 000 miles away through the internal antenna in the Temperature Clock.

However, due to the nature of the Earth’s Ionosphere, reception is very limited during

daylight hours. The Temperature Clock will search for a signal every night when

reception is best. The WWVB radio station derives its signal from the NIST Atomic

clock in Boulder, Colorado. A team of atomic physicists is continually measuring every

second, of every day, to an accuracy of ten billionths of a second per day. These

physicists have created an international standard, measuring a second as 9,192,631,770

vibrations of a Cesium-133 atom in a vacuum.

QUICK SET-UP GUIDE

1) Insert two AAA batteries into the remote transmitter.

2) Insert two AA batteries into the Temperature Clock.

3) Wait 10 minutes for WWVB reception and remote temperature.

4) If there is no WWVB reception, manually set the time and date (instructions

in the Program Mode).

5) Program the settings.

6) Mount the WS-8011UM in a suitable location, where WWVB and

transmitter signals can be received.

7) Mount the transmitter where remote temperature measurement is desired

(on the North side of a house for example).

DETAILED SET-UP GUIDE

I) BATTERY INSTALLATION

Note: To avoid start-up problems make sure that the batteries do not spring free.

A) REMOTE TEMPERATURE TRANSMITTER

1) Remove the battery cover. Place your thumb over

the two air-vent slots on the face of the Remote

Temperature Transmitter, push down gently, and

slide battery cover down and off. Observing the

correct polarity, install 2 AAA batteries. The

batteries will fit tightly (to avoid start-up problems make sure that they do

not spring free during installation).

2) Replace the battery cover.

B) TEMPERATURE CLOCK

1) Remove the battery cover,

located on the backside of the

unit and directly below the

function buttons.

2) Observe the correct polarity,

and install 2 AA batteries.

3) Replace the battery cover.

Note: After the batteries have

been installed a tone will sound,

and all the LCD’s (Liquid Crystal

Display) will briefly light up. The

indoor temperature, the date as “1/

1”, the weekday as “MON”, and

the remote temperature will be

displayed (within three minutes).

Also, the time will appear as “-:--” for approximately 1 minute. The WWVB search

is automatically initiated, and a tower icon appears and flashes with the time colon

(no tower icon will appear if the WWVB is too weak to be detected, and the time

display will remain on “-:--”). While the WWVB search is being conducted various

numbers will appear in the time display. Within 10 minutes the Temperature Clock

will either display the WWVB time, or discontinue the search if the time is not

found. If the search is cancelled “-:--” will appear in the time LCD. The

Temperature Clock will conduct a WWVB search every hour until the first signal is

found. Once the WWVB time is found, a search is automatically conducted nightly

at midnight. If the signal is found at midnight, the tower icon will remain, if not,

another search will take place every hour (until 6:00 am) until the signal is found

successfully. If no signal is found during this period, the tower icon will not appear

and the clock will search again at 12:00 am the next night.

II) PROGRAM MODE

To enter the Program Mode hold down the “SET” button for 2 seconds, until

“-5EST” flashes in the Date LCD. The Program Mode is laid out in a manner that

allows you to program each function separately, or you can follow the instructions

entirely to program the Temperature Clock. Complete programming is usually done

for the initial set-up, and will require you to skip step 1 of programming sections C

Battery Compartment

Battery Cover

Battery

Cover

Outdoor tem

erature

Dat

WWVB

larm

Radio rece

tion

Indoor temperature or

seconds display

Weekday or

seconds display

through H. Press the “SNOOZE” button at any time to exit the Program Mode, or

wait approximately 15 seconds for the Temperature Clock to automatically return to

normal operation.

A) FUNCTION BUTTONS

There are 4 function buttons located on the backside of the Temperature Clock.

The function buttons are labeled: SET, +, ALARM, and SNOOZE.

B) TIME ZONE SETTING

1) Hold down the “SET” button for 2 seconds, the default setting “-5EST” will

flash in the Date LCD.

2) Press the “+” button to select the appropriate time zone. There are 13 time

zones to choose from:

3) Press the “SET” button to confirm the time zone setting, and to advance to

DST (Daylight saving time) setting.

C) DST (DAYLIGHT SAVING TIME) SETTING

Note: The DST default is “On”, meaning that the WWVB will automatically

change the time according to Daylight Saving Time in the spring and fall. For

areas that do not recognize DST changes (Arizona, Hawaii and parts of

Indiana) turn the DST “OFF”.

1) Hold down the “SET” button for 2 seconds (the selected time zone will

flash); press the “SET” button once more until “On” flashes in the time

LCD and “DST” flashes where the Weekday normally appears.

2) Press the “+” button to turn the DST off, as will be indicated by the display

of “OFF” in the time LCD.

3) Press the “SET” button to confirm the DST setting, and to advance to select

the language for the weekday.

-4ATL Atlantic Time

-5EST Eastern Time (default setting)

-6CST Central Time

-7MST Mountain Time

-8PST Pacific Time

-9ALA Alaskan Time

-10HAW Hawaiian Time

-11, -12 Next two time zones West of HAW

GMT Greenwich Mean Time

-1, -2, -3GMT Three time zones West of GMT

US English

F French

E Spanish

D) LANGUAGE SELECTION FOR THE WEEKDAY

1) Hold down the “SET” button for 2 seconds (the selected time zone will

flash), press the “SET” button 2 more times, until the default language

“US” flashes in the time LCD.

2) Press the “+” button to toggle through and to select the desired language.

There are 3 languages to select from:

Press the “SET” button to confirm the language setting, and to advance to

manually set the time.

E) TIME SETTING

Note: When the WWVB signal is found, that time will over-ride the manually set

time.

1) Hold down the “SET” button for 2 seconds (the selected time zone will

flash), press the “SET” button 3 more times, until the hour “12” flashes in

the time LCD.

2) Press the “+” button to select the hour. Note: when setting the hour, “PM”

will appear to the left of the hour display, if it is AM nothing will be

displayed.

3) Press the “SET” button to confirm the hour setting, and to shift to select the

minutes.

4) Press the “+” button to select the minutes.

5) Press the “SET” button to confirm the time setting, and to advance to

manually set the calendar.

F) CALENDAR SETTING

Note: When the WWVB signal is found, that date will over-ride the manually set

date.

1) Hold down the “SET” button for 2 seconds (the selected time zone will

flash), press the “SET” button 5 more times, until the default year “00”

flashes in the date LCD.

2) Press the “+” button to select the year.

3) Press the “SET” button to confirm the year, and to set the month.

4) The default month “1” will flash. Press the “+” button to select the

appropriate month.

5) Press the “SET” button to confirm the month, and to set the date.

6) The default date “1” will flash. Press the “+” button to select the

appropriate date.

7) Press the “SET” button to confirm the date, and to set the weekday.

8) The default weekday “MON” (depends on selected language) will flash.

Press the “+” button to select the appropriate weekday.

9) Press the “SET” button to confirm the calendar settings, and to advance to

select either 12 or 24-hour time display.

G) 12/24-HOUR SETTING

1) Hold down the “SET” button for 2 seconds (the selected time zone will

flash), press the “SET” button 9 more times, until the “12” hour time

display flashes in the time LCD.

2) Press the “+” button to toggle between 12 and 24 hour time.

3) Press the “SET” button to confirm the 12/24-hour time display, and to

advance to select either F or C.

H) SELECTING F OR C

1) Hold down the “SET” button for 2 seconds (the selected time zone will

flash), press the “SET” button 10 more times, until the default “F” flashes

in the time LCD.

2) Press the “+” button to toggle between F and C.

3) Press the “SET” button to confirm the F or C selection, and exit the

Program Mode.

III) FEATURES & OPERATIONS

A) CHANGING DISPLAY MODE (DAY, SECONDS, AND

TEMPERATURE)

There are three possible display modes to view the day, seconds, and

temperature. The month&date/weekday /indoor temperature/remote temperature

is the default.

To change the display:

1) Press the “+” button. The display should now show the

month&date/weekday/seconds/remote temperature

2) Press the “+” button a second time and the display will now show the

month&date/seconds/indoor temperature/remote temperature

3) Press the “+” button a third time and the display will return to the normal

display.

B) THE ALARM

1) SETTING THE ALARM

Note: The duration of the alarm is 85 seconds. After each of the first two

25 second periods, the rate of the alarm increases.

(a) Hold down the “ALARM” button for 5 seconds. The “TIME” icon to

the right of the minutes (in the time LCD) shifts to “ALARM”, and the

hour digit of the alarm flashes.

(b) Press the “+” button to set the alarm hour.

minutes.

(d) The alarm minutes flash, press the “+” button to set the alarm minutes.

(e) Press the “ALARM” button to confirm and to exit the alarm setting

mode.

Note: The alarm will be automatically set to sound when exiting the

alarm-setting mode (indicated by the alarm “sound” icon to the right

of the time).

2) ACTIVATING/DEACTIVATING THE ALARM

(a) The alarm will be automatically set to sound when exiting the alarm-

setting mode (indicated by the alarm “sound” icon to the right of the

time).

(b) Press the “ALARM” button to activate and deactivate the alarm. The

alarm “sound” icon to the right of the time will appear or disappear,

and the alarm time will be displayed briefly before returning to the

normal display mode.

3) ACTIVATING THE SNOOZE FUNCTION

(a) While the alarm is sounding, press the “SNOOZE” button to activate

the snooze function. The alarm “sound” icon and “SNOOZE” icon (to

the right of the time) will flash. The duration of the snooze function is

10 minutes, then the alarm will resume.

4) SUSPENDING ALARM

(a) While the alarm is sounding or the SNOOZE is active, press the

“ALARM” button to suspend the alarm until the next day.

C) INDOOR TEMPERATURE

The Indoor Temperature appears on the right side of the Date LCD. The

temperature is checked every 10 seconds, and updated whenever there is a

change.

D) REMOTE TEMPERATURE

The remote temperature will be shown on the right side of the lower LCD

screen. The Weather Temperature Station receives the outdoor temperature (F

or C) from the Remote Temperature Transmitter, and the temperature appears

in the OUTDOOR LCD. The Remote Temperature Transmitter transmits a new

temperature to the Weather Temperature Station 3 times every 10 minutes.

MOUNTING

There are two possible ways to mount the Temperature Clock: 1) use of the foldout table

stands, or 2) wall mounting.

E) FOLDOUT TABLE STANDS

The Foldout table stand legs are located on the

backside, at the lower corners, and on both sides of

the battery cover. The hinges are towards the edges

of the Temperature Clock, and the ends (with no

hinge) need to be folded out towards the edge. Once

the Foldout table stands are extended, place the

Temperature Clock in an appropriate location.

F) WALL MOUNTING

1) Using a straightedge, horizontally space at 3-

15/16 of an inch (100.58mm) three screw

positions on a wall.

2) Install three mounting screws (not included) into

a wall within transmission range—leaving

approximately 3/16 of an inch (5mm) extended

from the wall.

3) Place the Temperature Clock onto the screws, using the hanging holes on

the backside. Gently pull the Temperature Clock down to lock the screws

into place.

IV) THE REMOTE TEMPERATURE TRANSMITTER

A) The Remote Temperature Transmitter can be mounted in two ways: 1) with the

use of screws, or 2) using the adhesive tape.







Hanging Holes

Foldout Table Stands

Function Buttons

B) MOUNTING WITH SCREWS

1) Remove the mounting bracket from the Remote Temperature Transmitter.

The bracket should snap off easily.

2) Place the mounting bracket over the desired location. Through the three

screw holes of the bracket, mark the mounting surface with a pencil.

3) Where marked, start the screw holes into the mounting surface.

4) Screw mounting bracket onto the mounting surface. Ensure that the screws

are flush with the bracket.

5) Snap the Remote Temperature Transmitter onto the mounted bracket.

C) MOUNTING WITH ADHESIVE TAPE

1) With a nonabrasive solution, clean and dry the back of the mounting bracket

and the mounting surface to ensure a secure hold. The mounting surface

should be smooth and flat.

2) Remove the protective strip from one side of the tape. Adhere the tape to

the designated area on the back of the mounting bracket. Remove the

protective strip from the other side of the tape. Position the Remote

Temperature Transmitter in the desired location, ensuring that the Weather

Temperature Station can receive the signal.

V) MAINTENANCE & CARE

Extreme temperatures, vibrations, and shock should be avoided to prevent

damage to the units.

Clean displays and units with a soft, damp cloth. Do not use solvents or

scouring agents—they may mark and damage the displays and casings.

Do not submerge in water.

Immediately remove all low powered batteries to avoid leakage and damage.

Replace with new batteries only, and of recommended size.

Opening the casings invalidates the warranty. Do not try to repair the units.

Contact La Crosse Technology for Repairs.

TROUBLESHOOTING

Problem: The LCD is faint.

Solution: 1) Replace the batteries.

Problem: “OFL” appears in the indoor temperature LCD.

Solution: 1) Move unit to an area with warmer or cooler surrounding

temperature. Current surrounding temperatures are outside

measuring range.

Problem: No reception of WWVB signal.

Solution: 1) It may help reception to face the front of the Temperature

Clock in the general direction of Ft. Collins, Colorado.

2) Wait overnight for signal.

3) Be sure the Temperature Clock is at least 6 feet from any

electrical devices, i.e. TV sets, computers, or other radio

controlled clocks.

4) Remove batteries for five minutes, reinsert and leave the unit

alone overnight without pressing buttons.

5) If problems persist contact La Crosse Technology.

Problem: Hour is incorrect (minute and date are correct).

Solution: 1) Be sure correct time zone and daylight saving time are

selected.

Problem: “--.-” appears in outdoor temperature LCD

Solution: 1) Check batteries in remote

2) If batteries are replaced in remote, the unit must be re-started.

Remove all batteries, and then follow start up procedure.

Problem: “OFL” appears in the outdoor temperature LCD

Solution: 1) Remote temperature is out of range.

2) Check batteries.

3) Interference from an outside source (cordless telephone, etc.)

4) Contact La Crosse Technology.

Note: For any questions not answered, contact La Crosse Technology with the contact

information found at the end of this instructional manual.

SPECIFICATIONS FOR WS-8011UM

Temperature:

Measuring range: 32F to 122F with 0.2F resolution (indoor)

-21.8F to 140F with 0.2F resolution (outdoor)

(0C to 50C with 0.1C resolution)

Checking intervals: Every 10 seconds indoor, 3 times in 10 minutes

for remote temperature.

Power source:

Battery type: Station: 2 x AA, 1.5V (Alkaline)

Transmitter: 3 x AAA, 1.5V (Alkaline)

Battery life: Approximately 12 months

Dimensions (L x W x H): 11.4 x 0.98 x 7.5 in (290 x 25 x 190mm)

WARRANTY INFORMATION

La Crosse Technology provides a 1-year warranty on this Temperature Clock. Contact

La Crosse Technology immediately upon discovery of any defects covered by this

warranty.

Before sending the Temperature Clock in for repairs, contact La Crosse Technology. The

Temperature Clock will be repaired or replaced with the same or similar model.

This warranty does not cover any defects resulting from improper use, unauthorized

repairs, faulty batteries, or the Clocks inability to receive a signal due to any source of

interference.

LA CROSSE TECHNOLOGY WILL NOT ASSUME LIABILITY FOR INCIDENTAL,

CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED

WITH THE OPERATION OR MALFUNCTION OF THIS TEMPERATURE CLOCK.

THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR

PUBLIC INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT OF

CHILDRENS’ REACH.

This warranty gives you specific legal rights. You may also have other rights specific to

your State. Some States do not allow the exclusion of consequential or incidental

damages; therefore the above exclusion of limitation may not apply to you.

For warranty work, technical support, or information contact:

La Crosse Technology, Ltd

2809 Losey Blvd. S.

La Crosse, WI 54601

Phone: 608.782.1610

Fax: 608.796.1020

e-mail: support@lacrossetechnology.com (warranty work)

sales@lacrossetechnology.com (information on other products)

web: www.lacrossetechnology.com

FCC ID: OMO-01RX (receiver)

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO

THE FOLLOWING TWO CONDITIONS:

1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND

2. THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED, INCLUDING INTERFERENCE

THAT MAY CAUSE UNDESIRED OPERATION.

attery

Cover

WS-8011UM – TX6U

433 MHz

Radio Controlled Temperature Clock

Instruction Manual



TABLE OF CONTENTS

Topic Page

Inventory of Contents/ Additional Equipment 16

About WWVB 16

Quick Set-Up Guide 16-17

Detailed Set-Up Guide

Battery Installation 17-18

Program Mode

Function Buttons 18

Time Zone Setting 18-19

DST (Daylight Saving Time) Setting 19

Language Selection 19

Time Setting 19

Calendar Setting 20

12/24-Hour Setting 20

Selecting F or C 21

Features & Operations

Changing Display Mode (seconds, temperature) 21

The Alarm 21

Indoor Temperature 22

Remote Temperature 22

Mounting 23-24

Maintenance & Care 24

Troubleshooting 24-25

Specifications 25

Warranty Information 26

INVENTORY OF CONTENTS

4) WS-8011UM

5) TX6U remote temperature transmitter

6) Instruction manual and warranty card.

ADDITIONAL EQUIPMENT (not included)

5) Two fresh 1.5V AA batteries (for the temperature clock).

6) Two fresh 1.5V AA batteries (for the remote temperature transmitter).

7) Three wall-hanging screws.

8) Appropriate screwdriver for screws.

ABOUT WWVB (Radio Controlled Time)

The NIST (National Institute of Standards and Technology—Time and Frequency

Division) WWVB radio station is located in Ft. Collins, Colorado, and transmits the exact

time signal continuously throughout the United States at 60 kHz. The signal can be

received up to 2, 000 miles away through the internal antenna in the temperature clock.

However, due to the nature of the Earth’s Ionosphere, reception is very limited during

daylight hours. The temperature clock will search for a signal every night when

reception is best. The WWVB radio station derives its signal from the NIST Atomic

clock in Boulder, Colorado. A team of atomic physicists is continually measuring every

second, of every day, to an accuracy of ten billionths of a second per day. These

physicists have created an international standard, measuring a second as 9,192,631,770

vibrations of a Cesium-133 atom in a vacuum. For more information about WWVB

please see the NIST website at http://www.boulder.nist.gov/timefreq/stations/wwvb.htm

QUICK SET-UP GUIDE

Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries.

1. Have the indoor station and outdoor remote 3 to 5 apart.

2. Batteries should be out of both units for 10 minutes.

3. Place the batteries into the remote temperature sensor first then into the

temperature clock.

(All remote temperature sensors must be started before the temperature

clock)

4. DO NOT PRESS ANY BUTTONS FOR 10 MINUTES.

In this time the temperature clock and remote temperature sensor will start to talk to each

other and the temperature clock will show both the indoor temperature and an outdoor

temperature. If the temperature clock does not display both temperatures after the 10

minutes please retry the set up as stated above. After both indoor and outdoor

temperatures are displayed for 10 minutes you can place your remote temperature sensor

outdoors and set your time.

attery

Cover

The remote temperature sensor should be placed in a dry, shaded area. The remote

temperature sensor has a range of 80 feet. Any walls that the signal will have to pass

through will reduce distance. An outdoor wall or window will have 20 to 30 feet of

resistance and an interior wall will have 10 to 20 feet of resistance. Your distance plus

resistance should not exceed 80 ft. in a straight line.

NOTE: Fog and mist will not harm your remote temperature sensor but direct rain must

be avoided.

To complete the set up of your temperature clock after the 10 minutes have passed please

follow the steps below.

DETAILED SET-UP GUIDE

VI) BATTERY INSTALLATION

Note: To avoid start-up problems make sure that the batteries do not spring free.

A) REMOTE TEMPERATURE TRANSMITTER

1) Remove the battery cover. Place your thumb over

the two air-vent slots on the face of the remote

temperature sensor, push down gently, and slide

battery cover down and off.

2) Observing the correct polarity, install 2 AA batteries.

The batteries will fit tightly (to avoid start-up

problems make sure that they do not spring free

during installation).

3) Replace the battery cover.

B) TEMPERATURE CLOCK

1) Remove the battery cover,

located on the backside of the

temperature clock and directly

below the function buttons.

2) Observe the correct polarity,

and install 2 AA batteries.

3) Replace the battery cover.

Note: After the batteries have

been installed a tone will sound,

and all the LCD’s (Liquid

Crystal Display) will briefly

light up. The indoor

Battery Compartment

Battery Cover

Outdoor tem

erature

Dat

WWVB

larm

Radio rece

tion

Indoor temperature or

seconds display

Weekday or

seconds display 18

temperature, the date as “1/ 1”, the weekday as “MON”, and the remote temperature

will be displayed (within three minutes). Also, the time will appear as “-:--” for

approximately 1 minute. The WWVB search is automatically initiated, and a tower

icon appears and flashes with the time colon (no tower icon will appear if the

WWVB is too weak to be detected, and the time display will remain on “-:--”).

While the WWVB search is being conducted various numbers will appear in the

time display. Within 10 minutes the temperature clock will either display the

WWVB time, or discontinue the search if the time is not found. If the search is

cancelled “-:--” will appear in the time LCD. The temperature clock will conduct a

WWVB search every hour until the first signal is found. Once the WWVB time is

found, a search is automatically conducted nightly at midnight. If the signal is found

at midnight, the tower icon will remain, if not, another search will take place every

hour (until 6:00 am) until the signal is found successfully. If no signal is found

during this period, the tower icon will not appear and the clock will search again at

12:00 am the next night.

VII) PROGRAM MODE

To enter the Program Mode hold down the “SET” button for 2 seconds, until

“-5EST” flashes in the Date LCD. The Program Mode is laid out in a manner that

allows you to program each function separately, or you can follow the instructions

entirely to program the temperature clock. Complete programming is usually done

for the initial set-up, and will require you to skip step 1 of programming sections C

through H. Press and release the “SNOOZE” button at any time to exit the Program

Mode, or wait approximately 15 seconds for the temperature clock to automatically

return to normal operation.

A) FUNCTION BUTTONS

There are 4 function buttons located on the backside of the temperature clock.

The function buttons are labeled: “SET”, “+”, “ALARM”, and “SNOOZE”.

B) TIME ZONE SETTING

1) Hold down the “SET” button for 2 seconds, the default (factory) setting

“-5EST” will flash in the Date LCD.

2) Press and release the “+” button to select the appropriate time zone. There

are 13 time zones to choose from:

-4ATL Atlantic Time

-5EST Eastern Time (default setting)

-6CST Central Time

-7MST Mountain Time

-8PST Pacific Time

-9ALA Alaskan Time

-10HAW Hawaiian Time

-11, -12 Next two time zones West of HAW

GMT Greenwich Mean Time

-1, -2, -3GMT Three time zones West of GMT

US English

F French

E Spanish

3) Press and release the “SET” button to confirm the time zone setting, and to

advance to DST (Daylight saving time) setting.

C) DST (DAYLIGHT SAVING TIME) SETTING

Note: The DST default is “On”, meaning that the WWVB will automatically

change the time according to Daylight Saving Time in the spring and fall. For

areas that do not recognize DST changes (Arizona, Hawaii and parts of

Indiana) turn the DST “OFF”.

1) Hold down the “SET” button for 2 seconds (the selected time zone will

flash).

2) Press and release the “SET” button once more until “On” flashes in the time

LCD and “DST” flashes where the Weekday normally appears.

3) Press and release the “+” button to turn the DST off, as will be indicated by

the display of “OFF” in the time LCD.

4) Press and release the “SET” button to confirm the DST setting, and to

advance to select the language for the weekday.

D) LANGUAGE SELECTION FOR THE WEEKDAY

1) Hold down the “SET” button for 2 seconds (the selected time zone will

flash).

2) Press and release the “SET” button 2 times until the default language “US”

flashes in the time LCD.

3) Press and release the “+” button to toggle through and to select the desired

language. There are 3 languages to select from:

4) Press and release the “SET” button to confirm the language setting, and to

advance to manually set the time.

E) TIME SETTING

Note: When the WWVB signal is found, that time will over-ride the manually set

time.

1) Hold down the “SET” button for 2 seconds (the selected time zone will

flash).

2) Press and release the “SET” button 3 times until the hour “12” flashes in

the time LCD.

3) Press and release the “+” button to select the hour.

Note: when setting the hour, “PM” will appear to the left of the hour display, if

it is AM nothing will be displayed.

4) Press and release the “SET” button to confirm the hour setting, and to shift

to select the minutes.

5) Press and release the “+” button to select the minutes.

6) Press and release the “SET” button to confirm the time setting and to

advance to manually set the calendar.

F) CALENDAR SETTING

Note: When the WWVB signal is found, that date will over-ride the manually set

date.

1) Hold down the “SET” button for 2 seconds (the selected time zone will

flash).

2) Press and release the “SET” button 5 times until the default year “00”

flashes in the date LCD.

3) Press and release the “+” button to select the year.

4) Press and release the “SET” button to confirm the year, and to set the

month.

5) The default month “1” will flash.

6) Press and release the “+” button to select the appropriate month.

7) Press and release the “SET” button to confirm the month and to set the date.

8) The default date “1” will flash.

9) Press and release the “+” button to select the appropriate date.

10) Press and release the “SET” button to confirm the date and to set the

weekday.

11) The default weekday “MON” (depends on selected language) will flash.

12) Press and release the “+” button to select the appropriate weekday.

13) Press and release the “SET” button to confirm the calendar settings and to

advance to select either 12 or 24-hour time display.

G) 12/24-HOUR SETTING

Note: 12-hour uses AM/PM, 24-hour is also known as “military” time.

1) Hold down the “SET” button for 2 seconds (the selected time zone will

flash).

2) Press and release the “SET” button 9 times until the “12” hour time display

flashes in the time LCD.

3) Press and release the “+” button to toggle between 12 and 24 hour time.

4) Press and release the “SET” button to confirm the 12/24-hour time display

and to advance to select either F or C.

Table des matières

Autres manuels La Crosse Technology Horloge

La Crosse Technology

La Crosse Technology BBB85289 Manuel utilisateur

La Crosse Technology

La Crosse Technology WT-3122A Manuel utilisateur

La Crosse Technology

La Crosse Technology WT-8005U Manuel utilisateur

La Crosse Technology

La Crosse Technology WS-8236U Manuel utilisateur

La Crosse Technology

La Crosse Technology WS-6118AL-IT Manuel utilisateur

La Crosse Technology

La Crosse Technology WT-3143A Manuel utilisateur

La Crosse Technology

La Crosse Technology L78359v2 Manuel utilisateur

La Crosse Technology

La Crosse Technology 404-3451 Manuel utilisateur

La Crosse Technology

La Crosse Technology WS-8055U Manuel utilisateur

La Crosse Technology

La Crosse Technology WS-8117 Manuel utilisateur

La Crosse Technology

La Crosse Technology 512-1422WH Manuel utilisateur

La Crosse Technology

La Crosse Technology 404-1225 Manuel utilisateur

La Crosse Technology

La Crosse Technology WS-6002U Manuel utilisateur

La Crosse Technology

La Crosse Technology K86302 Manuel utilisateur

La Crosse Technology

La Crosse Technology WS-8001U Manuel utilisateur

La Crosse Technology

La Crosse Technology C86279v4 Manuel utilisateur

La Crosse Technology

La Crosse Technology WS-6118 Manuel utilisateur

La Crosse Technology

La Crosse Technology 404-1225 Manuel utilisateur

La Crosse Technology

La Crosse Technology BBB84022 Manuel utilisateur

La Crosse Technology

La Crosse Technology 513-1311OT Manuel utilisateur

La Crosse Technology

La Crosse Technology Radio Controlled Analog Clock WT-3181bz Manuel utilisateur

La Crosse Technology

La Crosse Technology Wattz 2.0 Manuel utilisateur

La Crosse Technology

La Crosse Technology WS-8418U-IT Manuel utilisateur

La Crosse Technology

La Crosse Technology WS6158-IT Manuel utilisateur

Manuels Horloge populaires d'autres marques

Silicon Laboratories

Silicon Laboratories SI5324 Manuel utilisateur

Heathkit

Heathkit GC-1005 Manuel utilisateur

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Manuel utilisateur

Andrew O'Malley

Andrew O'Malley DOTKLOK Manuel utilisateur

ALGE-Timing

ALGE-Timing ASC3 Manuel utilisateur

Bodet

Bodet Profil 960 Manuel utilisateur

Nixie Clock

Nixie Clock Divergence Meter Manuel utilisateur

Mini Gadgets

Mini Gadgets MCPro Manuel utilisateur

Casio

Casio TMR-200 Manuel utilisateur

Progetti

Progetti ILTEMPOSTRINGE Manuel

BVItech

BVItech BV-101 Manuel utilisateur

Progetti

Progetti KALIMERO Manuel

Sharp

Sharp SPC900 Manuel utilisateur

Datexx

Datexx DF0063 Manuel utilisateur

LG LEC-005 Manuel utilisateur

IKEA

IKEA ROTBLÖTA Manuel utilisateur

U-Line

U-Line Н-2811 Manuel utilisateur

Digiview

Digiview RC305EL Manuel utilisateur