Kyocera FS-8000C Series Manuel utilisateur
FS-8000C Series Printers
PF-30A for FS-8000C
PD-30 for FS-8000CD
Important!
Installation should be performed only by a qualified service personnel. Kyocera Mita
assumes no liability for any damage caused by an improper installation of the printer.
No!
Yes!
3
1 2
4 5 6
7 8 9
10
11 12 13 14
Placing the Printer
Checking Parts and ComponentsUnpacking
Using another topple-resistant bracket,
stack and joint the middle and top paper
feeder.
Place the printer over the paper feeders (by
at least two persons).
Join the printer and topmost paper feeder
with the jig provided by using one screw.
Using a topple-resistant bracket (supplied
with the CA-31B caster kit), stack and joint
the bottom and middle paper feeder.
Open the front cover. Pull out thoroughly the paper feed unit. Unscrew the screw. Remove the lock pin
and release the (green-colored) lock lever.
Pull out the primary transfer unit until it
stops.
While pushing the gray lever, pull out
the primary transfer unit. Make sure
not to scratch the roller.
Installation Guide
Continued on
the Reverse Page
Attaching the Caster kit (purchased
separately): Remove each one screw to
remove four feet.
Place the paper feeder in a proper location.
Lock the stopper for each caster. Turn the
bolts to adjust height.
Install the filter duct and the quick
reference guide holder. Peel the protective
tape off when attaching the holder.
Be sure to face
the longer end
towards the front
of the feeder.
Gray Lever
Filter Duct
Quick Reference
Guide Holder
Unpacking the Printer
Unpacking
the Paper Feeder
Warning: To
avoid injury, the
printer must be
lifted and
carried by two
persons or
more.
The following setup assumes three paper feeders to be installed with the printer (including the one supplied as a standard accessory), which requires a CA-31B caster kit to
be installed on the bottom of the bottom paper feeder. If the extra paper feeders are not installed, the CA-31 casters may be used. See the Operation Guide for more details.
1 Documents
Installation Guide (This sheet)
Quick Reference Guide
CD-ROM
2 Cyan Developer
3 Magenta Developer
4 Yellow Developer
5 Black Developer
6 Cyan Toner Container
7 Magenta Toner Container
8 Yellow Toner Container
1
2
34
5
6
7
8
9
10
11
12
13
13
14
15
16
17
18
9 Black Toner Container
10 Secondary Transfer Unit
11 Fuser Unit
12 Oil Unit
13 Waste Toner Bottles
14 Power Cord
15 Filter Duct
16 Quick Reference Guide Holder
17 Jig (Used in step 9)
18 Screws (Used in steps 9 and 16)
Lock Lever
Screw
Lock Pin
Stand the paper feeder on its back side.
Install the caster kit onto the bottom of the
paper feeder.
Installing the Fuser Unit, Oil Unit, Secondary Transfer Unit, and Waste Toner Bottle
15 16 17 18
23 24 25 26
27 28 29 30
31 32 33 34
Inserting the Developer Units
Installing the Fuser Unit, Oil Unit, Secondary Transfer Unit, and Waste Toner Bottle
Close the paper feed unit.
Set the black developer facing the
developing roller towards you.
Open the paper guide. Insert the fuser unit
onto the paper feed unit.
35
Installing the Toner Containers
Shake each toner container well
before use. Install the four toner
containers into their corresponding
developer units.
36
Close the front cover.
Fix the fuser unit with one screw. Open the fuser top cover by the lock
buttons.
Pull out the paper feed unit. Reinstall the primary transfer unit. Insert
it thoroughly on the rails.
Close the lock lever. Fix the screw.
Reinsert the paper feed unit.
Set the cyan developer. Set the magenta developer. Set the yellow developer.
Pull out the process frame.
Paper Guide
Fuser Unit
Lock Button
(green-colored)
Lock Button
(green-colored)
Fuser
Top Cover
19 20 21 22
Firmly tighten two screws. Close the fuser
top cover, then close the paper guide.
Remove the oil sealing tapes from the
oil unit. Unlatch three latches and then
take out the oil unit from the cover.
Install the oil unit onto the fuser unit until it is
locked. Install the waste toner bottle.
Connect the tab from the paper feed unit to
the terminal of secondary transfer unit.
Then, install the secondary transfer unit.
Waste Toner Bottle
Cyan
Magenta
Yellow
Black
37
Making Connections
Connect to the computer.
38
Connect the power cord to the
power outlet. Turn on the printer
power switch.
Network
Interface
Card
Parallel
Interface
2001 by Kyocera Corporation. 14-9, Tamagawadai 2-Chome, Setagaya Ward, Tokyo 158-8610 Japan. All rights reserved.
Peel off the tapes from the developer units
and remove the protective pad from each
unit.
Close the process frame and then close
the stoppers. Fix the two (A) screws first,
and then fix the two (B) screws.
Secondary
Transfer Unit
Oil Unit
Cover
Oil Sealing Tapes
Terminal
Tab
Unscrew the four screws. Free the two
stoppers.
Developing
Roller
Black
Cyan
Magenta
Yellow
Process Frame
Printed in Japan 2001.08 EI 2BM80020C
Ce manuel convient aux modèles suivants
3
Autres manuels Kyocera Imprimante
Kyocera
Kyocera Ecosys FS-C5300DN Manuel utilisateur
Kyocera
Kyocera FS-2020D Manuel utilisateur
Kyocera
Kyocera KM-1510 Manuel
Kyocera
Kyocera TASKalfa 2420w Manuel utilisateur
Kyocera
Kyocera FS-C5020N Manuel utilisateur
Kyocera
Kyocera ECOSYS P6230cdn Manuel utilisateur
Kyocera
Kyocera ECOSYS P4040dn Manuel utilisateur
Kyocera
Kyocera ECOSYS P5026cdw Manuel utilisateur
Kyocera
Kyocera FS C8026N Manuel utilisateur
Kyocera
Kyocera FS-600 Manuel utilisateur
Kyocera
Kyocera ECOSYS M6230cidn Manuel utilisateur
Kyocera
Kyocera C8100DN - Color Laser Printer Manuel utilisateur
Kyocera
Kyocera TASKalfa 2320 Manuel utilisateur
Kyocera
Kyocera PA2000w Manuel utilisateur
Kyocera
Kyocera Ecosys FS-1200 Manuel utilisateur
Kyocera
Kyocera ECOSYS P5021cdn Manuel utilisateur
Kyocera
Kyocera ECOSYS FS-C8650DN Manuel utilisateur
Kyocera
Kyocera TASKalfa 7004i Manuel utilisateur
Kyocera
Kyocera ECOSYS P6021cdn Manuel utilisateur
Kyocera
Kyocera FS-2100DN Manuel d'installation et d'exploitation
