KWIK GOAL 9B51 Manuel utilisateur
Crossbar (2)
(Part# SEE TABLE)
THIS UNIT MUST BE ANCHORED ACCORDING TO THESE INSTRUCTIONS AT ALL TIMES
NOTE: Components may be packaged in one or more additional boxes.
*THIS UNIT MUST BE ASSEMBLED BY A MINIMUM OF TWO QUALIFIED PERSONS*
2. Read through entire instruction before beginning assembly and installation.
NOTICE Sunlight reflecting off polycarbonate panels can contribute to increased temperatures of
surrounding objects. In certain situations, these increased temperatures can damage some artificial turf
surfaces. Kwik Goal is not responsible for any damage to artificial turf.
1. Unpack all parts and check for damage that may have occurred during shipping. If damage has occurred,
notify Kwik Goal immediately. Lay out all parts. Remove all cardboard and packaging immediately. Wet or
damp packaging may damage contents.
ASSEMBLY INSTRUCTIONS FOR ALL 9B51 PORTABLE SHELTER FRAMES
Left Post (1)
(Part# UZ1103)
67-1/8”
Date of manufacture sticker
67-1/8”
Right Post (1)
(Part# UZ1103)
(A)
PART #
SHELTER WIDTH
DIM (A)
UZ1559
30’
362-3/8”
UZ1116
24’
287-3/4”
UZ1433
21’
250-7/16”
UZ1434
18’
213-1/8”
UZ1435
15’
175-13/16”
UZ1436
12’
138-1/2”
UZ1114
9’
101-3/16”
NZ373 Rev. 12/04/19
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE THREAT
OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED UNDER KWIK GOAL’S
PRODUCT GUARANTEE. DO NOT LEAVE THIS EQUIPMENT UNATTENDED.
Parts
140 Pacific Drive Quakertown, PA 18951
800-531-4252 Kwikgoal.com
2015, Rev 2019 Kwik Goal Ltd. ©
READ CAREFULLY
IMPORTANT SAFETY INSTRUCTIONS
1. Lifting and moving heavy field equipment can be dangerous if not done
properly. All Kwik Goal shelters must be moved by qualified personnel who are
experienced in moving large, heavy field equipment. Kwik Goal recommends
storing dolly and wheels in a secured area to prevent unauthorized use.
3. Do not attempt to lift, move, or remove anchors from any shelter in windy
conditions.
2. A minimum of four qualified, experienced people are required to install wheels
and move shelter.
4. Shelters must not be left unattended when wheels are installed.
5. Shelter must be on level, flat ground to use dolly handle and/or wheels.
6. Dolly is to be used as a wheel transport/storage and shelter lifting device. Do
not use dolly to move shelter.
7. Use extreme caution when pushing shelter. Excessive force can overturn
shelter. Always push at lowest point on shelter frame possible.
8. Do not push shelter directly from the front to rear or rear to front. Push from
end to end. (Refer to 9B1201 - Shelter Dolly instructions for details.)
9. Always use two people to lift shelter with dolly. With one person maintaining
light pressure on the handle, the second may insert wheels into shelter. Install
both wheels before resting shelter on the ground. (Refer to 9B1201 - Shelter
Dolly instructions for details.)
NEVER LOWER SHELTER WITH ONLY ONE WHEEL INSTALLED
NZ373 Rev. 12/04/19
140 Pacific Drive Quakertown, PA 18951
800-531-4252 Kwikgoal.com
2015, Rev 2019 Kwik Goal Ltd. ©
Crossbar Corner (2)
(Part# UZ1211)
Post Corner (2)
(Part# UZ1099)
Left Panel (1)
(Part# UZ1098)
Polycarbonate (1)
(Part# WZ510)
Right Panel (1)
(Part# UZ1097)
Polycarbonate (1)
(Part# WZ464)
Center Panel (SEE TABLE)
(Part# UZ1096)
Polycarbonate (1)
(Part# WZ462)
THIS UNIT MUST BE ANCHORED ACCORDING TO THESE INSTRUCTIONS AT ALL TIMES
(Part# 10B103 Pack of 4)
Ground Anchor (4) Anchor Bracket (8)
(Part# UZ1430)
SHELTER WIDTH
QTY
30’
10
24’
8
21’
7
18’
6
15’
5
12’
4
9’
3
Note: Hardware is packed separately in one or more boxes.
Open all boxes and layout all sealed hardware packs
before beginning assembly.
Frame Hdw (Part#JZ131)
3/8” Lock Washer (Part# TZ65) (20)
3/8” X 1” Socket Head (Part# TZ323) (20)
Lift Hdw (Part# JZ137)
Anchor Chain (Part# VZ564-12) (4)
7/16” Flat Washer (Part# TZ171) (8)
1/2” Lock Nut (Part# TZ28) (4)
7/16” X 5-1/2” Hex Bolt (Part# TZ291) (4)
1/2” U-bolt (Part# TZ306) (2)
1/2” Flat Washer (Part# TZ297) (4)
7/16” X 5” Hex Bolt (Part# TZ307) (4)
Anchor Hdw (Part# JZ210)
7/16” Lock Nut (Part# TZ47) (4)
NZ373 Rev. 12/04/19
Left Base (1)
(Part# UZ1101)
50-1/8”
Right Base (1)
(Part# UZ1102)
50-1/8”
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE THREAT
OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED UNDER KWIK GOAL’S
PRODUCT GUARANTEE. DO NOT LEAVE THIS EQUIPMENT UNATTENDED.
Parts Continued
1/2” U-Bolt
Right Base
1/2” Lock Nut
1/2” Flat Washer
1/2” U-Bolt Left Base
1/2” Lock Nut
1/2” Flat Washer
THIS UNIT MUST BE ANCHORED ACCORDING TO THESE INSTRUCTIONS AT ALL TIMES
Ratchet with
1/2”, 9/16”, 5/8” & 3/4”
Sockets
1/2”, 9/16”, 5/8” & 3/4”
Wrenches
9/16
5/16” Hex wrench
Assembly Tools
Polyurethane Sealant
(Part# VZ837)
3. Hardware for this step is in Lift Hdw pack.
Attach 1/2” U-bolt to left and right bases.
NOTE: Tighten 1/2” nuts only until flush with end of U-bolts.
NZ373 Rev. 12/04/19
3/8” X 2-1/4” Hex Bolt (Part# TZ305) (7) (8) (9) (10) (11) (12) (14)
3/8” Square Nut (Part# TZ247) (12) (14) (16) (18) (20) (22) (26)
3/8” X 7/8” Hex Bolt (Part# TZ249) (5) (6) (7) (8) (9) (10) (12)
3/8” Flat Washer (Part# TZ60) (12) (14) (16) (18) (20) (22) (26)
5/16” Lock Nut (Part# TZ5) (12) (15) (18) (21) (24) (27) (33)
Panel Hdw (Part# JZ199, JZ202) 9ft 12ft 15ft 18ft 21ft 24ft 30ft
3/8” Lock Washer (Part# TZ65) (32) (34) (36) (38) (40) (42) (46)
Quantity per shelter length
5/16” X 3-3/4” Hex Bolt (Part# TZ264) (6) (9) (12) (15) (18) (21) (27)
5/16” Flat Washer (Part# TZ4) (18) (24) (30) (36) (42) (48) (60)
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE THREAT
OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED UNDER KWIK GOAL’S
PRODUCT GUARANTEE. DO NOT LEAVE THIS EQUIPMENT UNATTENDED.
THIS UNIT MUST BE ANCHORED ACCORDING TO THESE INSTRUCTIONS AT ALL TIMES
4. Hardware for this step is in Frame Hdw & Panel Hdw packs.
NOTE: Square nuts will float loose in channels until used later.
Assemble crossbar, bases, and post corners. Press joints together firmly before tightening bolts.
3/8” x 1”
Socket Head Cap Screw
3/8” Lock Washer
Crossbar
Right Base
3/8” Square Nut
Left Base
Crossbar
3/8” Lock Washer
3/8” x 1”
Socket Head Cap Screw
3/8” Square Nut (Qty=Center Panel Qty - 1)
Example: eight center panels = seven 3/8” square nuts
NZ373 Rev. 12/04/19
Post Corner
3/8” Square Nut
3/8” Lock Washer
3/8” x 1” Socket Head Cap Screw
Base
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE THREAT
OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED UNDER KWIK GOAL’S
PRODUCT GUARANTEE. DO NOT LEAVE THIS EQUIPMENT UNATTENDED.
THIS UNIT MUST BE ANCHORED ACCORDING TO THESE INSTRUCTIONS AT ALL TIMES
3/8” x 1” Socket Head Cap Screw
3/8” Lock Washer
3/8” Square Nut
Right Post
Crossbar Corner
Crossbar
Left Post
Crossbar Corner
Crossbar
Crossbar Corner
Right Post
Date of
manufacture sticker
Warning Sticker
Warning Sticker
Assemble crossbar, posts, and crossbar corners. Press joints together firmly before tightening bolts.
NOTE: Square nuts will float loose in channels until used later.
5. Hardware for this step is in Frame Hdw & Panel Hdw packs.
NZ373 Rev. 12/04/19
3/8” Square Nut (Qty=Center Panel Qty - 1)
3/8” x 1” Socket Head Cap Screw
3/8” Lock Washer
3/8” Square Nut
3/8” x 1”
Socket Head Cap Screw
3/8” Lock Washer
Crossbar
Left Post
Crossbar Corner
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE THREAT
OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED UNDER KWIK GOAL’S
PRODUCT GUARANTEE. DO NOT LEAVE THIS EQUIPMENT UNATTENDED.
THIS UNIT MUST BE ANCHORED ACCORDING TO THESE INSTRUCTIONS AT ALL TIMES
6. Hardware for this step is in Frame Hdw & Panel Hdw packs.
Insert one 3/8” square nut in each side of assembled base corner. Connect assembled base and post as shown.
Press joints together firmly before tightening bolts.
Assembled Post
Assembled Base
Post Corner
Post
3/8” x 1” Socket Head Cap Screw
3/8” Lock Washer
3/8” Square Nut
Assembled Post
Assembled Base
NZ373 Rev. 12/04/19
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE THREAT
OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED UNDER KWIK GOAL’S
PRODUCT GUARANTEE. DO NOT LEAVE THIS EQUIPMENT UNATTENDED.
THIS UNIT MUST BE ANCHORED ACCORDING TO THESE INSTRUCTIONS AT ALL TIMES
Left Panel
Right Panel
Assembled Frame
Assembled Frame
Left Panel
3/8” Square Nut
3/8” x 2- 1/4” Hex Bolt
3/8” Lock Washer
3/8” Flat Washer
3/8” x 7/8” Hex Bolt - make finger tight
to temporarily hold square nut in place.
Base
Left Panel
3/8” Square Nut
Do NOT tighten bolts at this time.
7. Hardware for this step is in Panel Hdw packs.
Attach right and left panels to assembled frame as shown.
3/8” x 2 -1/4” Hex Bolt
3/8” Lock Washer
3/8” Flat Washer
3/8” Square Nut
Left Panel
Assembled Frame
NZ373 Rev. 12/04/19
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE THREAT
OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED UNDER KWIK GOAL’S
PRODUCT GUARANTEE. DO NOT LEAVE THIS EQUIPMENT UNATTENDED.
THIS UNIT MUST BE ANCHORED ACCORDING TO THESE INSTRUCTIONS AT ALL TIMES
8. Turn shelter frame onto base and remove temporary 3/8” X 7/8” bolt then connect bottom of right and left
panel as shown.
Do NOT tighten bolts at this time.
3/8” x 7/8” Hex Bolt
3/8” Lock Washer
Assembled Frame
Left Panel
3/8” Square Nut
3/8” Flat Washer
Left Panel
Assembled Frame
Right Panel
Left Panel
Right Panel
Assembled Frame
NZ373 Rev. 12/04/19
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE THREAT
OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED UNDER KWIK GOAL’S
PRODUCT GUARANTEE. DO NOT LEAVE THIS EQUIPMENT UNATTENDED.
THIS UNIT MUST BE ANCHORED ACCORDING TO THESE INSTRUCTIONS AT ALL TIMES
9. Hardware for this step is in Panel Hdw packs.
Insert double end studs into left panel. Move unneeded square nuts in top and bottom crossbars away from left
side at least one center panel width.
Do NOT tighten bolts at this time.
NZ373 Rev. 12/04/19
Left Panel
Double End Stud
Double End Stud
Double End Stud
Top Crossbar
Right Panel
Left Panel
Bottom Crossbar
Top Crossbar
Move unneeded square nuts in top & bottom
crossbars away from panel at least a panel width.
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE THREAT
OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED UNDER KWIK GOAL’S
PRODUCT GUARANTEE. DO NOT LEAVE THIS EQUIPMENT UNATTENDED.
Autres manuels KWIK GOAL Abri
Manuels Abri populaires d'autres marques
Storage Canopy
Storage Canopy C3340R Manuel utilisateur
Frabill
Frabill ICE HUNTER 195 Manuel utilisateur
Shelters4Less
Shelters4Less SR1588 Manuel utilisateur
Sealey
Sealey Power Products GSS150819SD Manuel utilisateur
Crivit
Crivit 104155 Manuel utilisateur
No Butts Bin
No Butts Bin SR1558-F Manuel utilisateur