KTM 85 SX 2016 Manuel

SETUP INSTRUCTIONS 2016

85 SX

Art. no. 3213433en

INTRODUCTION 1

*3213433en*

3213433en

11/2015

INTRODUCTION

The work described in these setup instructions must be performed before the vehicle is delivered to the customer.

Read the setup instructions in their entirety before beginning work.

These setup instructions were written to correspond to the latest state of this series. We reserve the right to make changes in the interest

of technical advancement without at the same time updating this manual.

We shall not provide a description of general workshop methods. Likewise, safety rules that apply in a workshop are not specified here. It

is assumed that the work will be performed by a fully trained mechanic.

All specifications are non-binding. KTM Sportmotorcycle GmbH specifically reserves the right to modify or delete technical specifications,

prices, colors, forms, materials, services, designs, equipment, etc., without prior notice and without specifying reasons, to adapt these to

local conditions, as well as to stop production of a particular model without prior notice. KTM accepts no liability for delivery options, devi-

ations from illustrations and descriptions, misprints, and other errors. The models portrayed partly contain special equipment that does not

belong to the regular scope of supply.

Reproduction, even in part, as well as copying of all kinds, is permitted only with the express written permission of the copyright owner.

ISO 9001(12 100 6061)

According to the international quality management standard ISO 9001, KTM uses quality assurance processes that lead to

the maximum possible quality of the products.

Issued by: TÜV Management Service

KTM Sportmotorcycle GmbH

5230 Mattighofen, Austria

This document is valid for the following models:

85 SX 19/16 (F6001P9)

85 SX 17/14 (F6001P8)

1 MEANS OF REPRESENTATION 2

1.1 Symbols used

The meaning of specific symbols is described below.

Indicates an expected reaction (e.g. of a work step or a function).

Indicates an unexpected reaction (e.g. of a work step or a function).

Indicates a page reference (more information is provided on the specified page).

Indicates information with more details or tips.

Indicates the result of a testing step.

Denotes a voltage measurement.

Denotes a current measurement.

Denotes a resistance measurement.

1.2 Formats used

The typographical formats used in this document are explained below.

Proprietary name Identifies a proprietary name.

Name®Identifies a protected name.

Brand™ Identifies a trademark.

Underlined terms Refer to technical details of the vehicle or indicate technical terms, which are explained

in the glossary.

2 SETUP 3

2.1 Unpacking and setting up the vehicle

M00075-11

–Remove the box and the plastic packaging.

Info

An assistant prevents the motorcycle from falling over.

To avoid damaging the motorcycle during the setup, leave the protective

film on the vehicle until you have finished.

–Remove the separate enclosure and unpack it. Check that the scope of supply is

complete on the basis of the enclosed packing list.

402050-01

–Have a lift stand available.

Lift stand (78929955100)

–Together with an assistant, take the vehicle off the palette.

–Position the vehicle on a lift stand.

–Check the vehicle for transport damage.

201937-10

–Remove the tension belt.

The fork rebounds.

–Remove screw and wheel spindle. Lift the front wheel into the fork, position it,

and insert the wheel spindle.

–Mount and tighten the screw of the wheel spindle.

Guideline

Screw, front wheel spindle M20x1.5 35 Nm

(25.8 lbf ft)

201938-10

–Position the fender. Mount and tighten the screws.

Guideline

Remaining screws, chassis M6 10 Nm (7.4 lbf ft)

L02337-01

–Unpack the shock absorber.

–Position the shock absorber. Mount and tighten the screws.

Guideline

Screw, top shock absorber M12 60 Nm

(44.3 lbf ft)

Loctite®2701™

Screw, bottom shock

absorber

M12 60 Nm

(44.3 lbf ft)

Loctite®2701™

The longer screw is used at the bottom.

V00031-10

–Position the handlebar.

Info

Make sure the cables and wiring are positioned correctly.

–Position the handlebar clamps. Mount and tighten the screws evenly.

Guideline

Screw, handlebar clamp M8 20 Nm

(14.8 lbf ft)

2 SETUP 4

Info

The markings on the handlebar should be at the center of the handlebar

clamps.

Keep the gap widths equal when tightening.

201941-10

–Position the handlebar cushion and secure with cable ties.

201942-10

–Remove screw with the guide from the start number plate.

–Position the start number plate. Mount and tighten screw .

Guideline

Remaining screws, chassis M6 10 Nm (7.4 lbf ft)

Info

Ensure the holding lugs engage in the fender.

–Position the brake line and guide. Mount and tighten screw .

L02365-01

–Connect the fuel line to the fuel tap.

800042-10

–Mount the footrests with the springs and pins. Secure the pins using the washers

and cotter pins.

Pliers for footrest spring (58429083000)

201944-10

–Take the vehicle off the work stand.

–Operate the hand brake lever several times until the brake linings are seated cor-

rectly against the brake disc.

–Activate the front brake and compress the fork a number of times forcefully to align

the fork legs.

–Tighten screws .

Guideline

Screw, fork stub M8 15 Nm

(11.1 lbf ft)

–Refuel. ( p. 7)

–Prepare the vehicle according to the specifications in the KTM Dealer.net for han-

dover to the customer.

3 WORK 5

3.1 Raising the motorcycle with the lift stand

Note

Danger of damage The parked vehicle may roll away or fall over.

–Always place the vehicle on a firm and even surface.

401942-01

–Raise the motorcycle at the frame underneath the engine.

Lift stand (78929955100)

Neither wheel is in contact with the ground.

–Secure the motorcycle against falling over.

3.2 Removing the motorcycle from the lift stand

Note

Danger of damage The parked vehicle may roll away or fall over.

–Always place the vehicle on a firm and even surface.

402001-10

–Remove the motorcycle from the lift stand.

–Remove the lift stand.

–To park the motorcycle, insert plug-in stand into the left side of the wheel spin-

dle.

Info

Remove the plug-in stand before riding.

3.3 Installing the front wheel

Warning

Danger of accidents Reduced braking efficiency due to oil or grease on the brake discs.

–Always keep the brake discs free of oil and grease, and clean them with brake cleaner when necessary.

M01094-11

Main work

–Check the wheel bearing for damage and wear.

» If the wheel bearing is damaged or worn:

–Change the front wheel bearing.

–Clean and grease shaft seal rings and bearing surface of the spacers.

Long-life grease ( p. 10)

–Insert the spacers.

M01093-11

–Position the front wheel.

The brake linings are correctly positioned.

–Insert wheel spindle.

–Mount and tighten screw .

Guideline

Screw, front wheel spindle M20x1.5 35 Nm

(25.8 lbf ft)

3 WORK 6

–Operate the hand brake lever several times until the brake linings are lying correctly

against the brake disc.

–Remove the motorcycle from the lift stand. ( p. 5)

–Activate the front brake and compress the fork a number of times forcefully to align

the fork legs.

–Tighten screws .

Guideline

Screw, fork stub M8 15 Nm

(11.1 lbf ft)

Finishing work

–Remove the motorcycle from the lift stand. ( p. 5)

3.4 Installing the front fender

L02336-10

–Position the front fender. Mount and tighten screws .

Guideline

Remaining screws, chassis M6 10 Nm (7.4 lbf ft)

The holding lugs on the fender engage in the start number plate.

3.5 Installing the start number plate

L02335-11

–Position the start number plate. Mount and tighten screw .

Guideline

Remaining screws, chassis M6 10 Nm (7.4 lbf ft)

The holding lugs on the fender engage in the start number plate.

–Position the brake line and clamp. Mount and tighten screw .

3.6 Opening the filler cap

Danger

Fire hazard Fuel is highly flammable.

–Never refuel the vehicle near open flames or burning cigarettes, and always switch off the engine first. Be careful that no

fuel is spilt, especially on hot vehicle components. Clean up spilt fuel immediately.

–The fuel in the fuel tank expands when warm and may emerge if overfilled. Follow the instructions on refueling.

Warning

Danger of poisoning Fuel is poisonous and a health hazard.

–Fuel must not come into contact with the skin, eyes, or clothing. Do not breathe in the fuel vapors. If contact occurs with

the eyes, rinse with water immediately and contact a physician. Immediately clean contaminated areas on the skin with

soap and water. If fuel is swallowed, contact a physician immediately. Change clothing that has been contaminated with

fuel. Store fuel properly in a suitable canister and keep away from children.

Warning

Environmental hazard Improper handling of fuel is a danger to the environment.

–Do not allow fuel to get into the ground water, the ground, or the sewage system.

3 WORK 7

L02321-10

–Turn filler cap counterclockwise and lift it off.

3.7 Closing the filler cap

L02321-11

–Mount filler cap and turn it clockwise until the fuel tank is tightly closed.

Info

Run fuel tank breather hose without kinks.

3.8 Refueling

Danger

Fire hazard Fuel is highly flammable.

–Never refuel the vehicle near open flames or burning cigarettes, and always switch off the engine first. Be careful that no

fuel is spilt, especially on hot vehicle components. Clean up spilt fuel immediately.

–The fuel in the fuel tank expands when warm and may emerge if overfilled. Follow the instructions on refueling.

Warning

Danger of poisoning Fuel is poisonous and a health hazard.

–Fuel must not come into contact with the skin, eyes, or clothing. Do not breathe in the fuel vapors. If contact occurs with

the eyes, rinse with water immediately and contact a physician. Immediately clean contaminated areas on the skin with

soap and water. If fuel is swallowed, contact a physician immediately. Change clothing that is contaminated with fuel.

Warning

Environmental hazard Improper handling of fuel is a danger to the environment.

–Do not allow fuel to get into the ground water, the ground, or the sewage system.

–Switch off the engine.

–Open the filler cap. ( p. 6)

401522-10

–Fill the fuel tank with fuel up to measurement .

Guideline

Measurement of 35 mm (1.38 in)

Fuel tank capac-

ity, approx.

5.0 l

(1.32 US gal)

Super unleaded (98 octane) mixed

with 2-stroke engine oil (1:40)

( p. 9)

Engine oil, 2-stroke ( p. 9)

–Close the filler cap. ( p. 7)

4 TECHNICAL DATA 8

4.1 chassis tightening torques

Spoke nipple M4.5 6 Nm (4.4 lbf ft) –

Rear brake bolt M6 12 Nm (8.9 lbf ft) –

Remaining nuts, chassis M6 10 Nm (7.4 lbf ft) –

Remaining screws, chassis M6 10 Nm (7.4 lbf ft) –

Screw, ball joint of push rod on foot

brake cylinder

M6 10 Nm (7.4 lbf ft) –

Screw, foot brake cylinder M6 10 Nm (7.4 lbf ft) –

Screw, front brake disc M6 14 Nm (10.3 lbf ft) Loctite®243™

Screw, rear brake disc M6 14 Nm (10.3 lbf ft) Loctite®243™

Screw, throttle grip M6 4.5 Nm (3.32 lbf ft) –

Nut, rim lock M8 10 Nm (7.4 lbf ft) –

Remaining nuts, chassis M8 25 Nm (18.4 lbf ft) –

Remaining screws, chassis M8 25 Nm (18.4 lbf ft) –

Screw of brake caliper M8 25 Nm (18.4 lbf ft) Loctite®243™

Screw, bottom triple clamp M8 15 Nm (11.1 lbf ft) –

Screw, fork stub M8 15 Nm (11.1 lbf ft) –

Screw, handlebar clamp M8 20 Nm (14.8 lbf ft) –

Screw, rear sprocket M8 35 Nm (25.8 lbf ft) Loctite®243™

Screw, subframe M8 30 Nm (22.1 lbf ft) –

Screw, top triple clamp M8 20 Nm (14.8 lbf ft) –

Engine carrying screw M10 45 Nm (33.2 lbf ft) –

Remaining nuts, chassis M10 45 Nm (33.2 lbf ft) –

Remaining screws, chassis M10 45 Nm (33.2 lbf ft) –

Screw, foot brake lever M10 45 Nm (33.2 lbf ft) Loctite®243™

Screw, handlebar support M10 40 Nm (29.5 lbf ft) Loctite®243™

Screw, bottom shock absorber M12 60 Nm (44.3 lbf ft) Loctite®2701™

Screw, top shock absorber M12 60 Nm (44.3 lbf ft) Loctite®2701™

Nut, seat fixing M12x1 20 Nm (14.8 lbf ft) –

Nut, swingarm pivot M14x1.5 75 Nm (55.3 lbf ft) –

Nut, rear wheel spindle M20x1.5 80 Nm (59 lbf ft) –

Nut, steering stem M20x1.5 10 Nm (7.4 lbf ft) –

Screw, front wheel spindle M20x1.5 35 Nm (25.8 lbf ft) –

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels KTM Moto

KTM

KTM 1190 RC8 R EU/UK 2009 Manuel utilisateur

KTM

KTM 250 XC TPI 2020 Manuel

KTM

KTM 950 R Manuel utilisateur

KTM

KTM 450 EXC SIX DAYS Manuel

KTM

KTM 450 SX-F 2023 Manuel utilisateur

KTM

KTM 990 Adventure USA 2010 Manuel utilisateur

KTM

KTM SX-E 5 Manuel

KTM

KTM 1290 Super Adventure Manuel utilisateur

KTM

KTM 1290 Super Duke R 2019 Manuel

KTM

KTM 950 ADVENTURE 2003 Mode d'emploi

KTM

KTM 990 Adventure EU 2009 Manuel utilisateur

KTM

KTM 250 EXC-F AUS 2009 Manuel

KTM

KTM 450 EXC-F 2017 Mode d'emploi

KTM

KTM 250 EXC-F Six Days 2021 Manuel

KTM

KTM 85 SX 2020 Manuel

KTM

KTM 690 SUPERMOTO EU Packaging 5 2008 Manuel

KTM

KTM Freeride 350 2017 Series Manuel utilisateur

KTM

KTM 250 EXC-F 2021 Manuel utilisateur

KTM

KTM 400 SX RACING 2000 Guide de l'utilisateur

KTM

KTM 450 EXC-F 2023 Manuel utilisateur

KTM

KTM 125 LC2 1998 Guide de l'utilisateur

KTM

KTM 660 RALLY 2004 Manuel utilisateur

KTM

KTM Super Duke 990s Manuel utilisateur

KTM

KTM 250 EXC Manuel utilisateur

Manuels Moto populaires d'autres marques

OHVALE

OHVALE GP-0 Manuel de la liste des pièces

Yamaha

Yamaha Star XV19CTSZ 2009 Manuel utilisateur

HYOSUNG

HYOSUNG ST7 Manuel utilisateur

Husqvarna

Husqvarna FC 250 2016 Manuel utilisateur

Ducati

Ducati SCRAMBLER 800 Manuel d'instructions

MOTO GUZZI

MOTO GUZZI QUOTA 1100 ES Manuel utilisateur

APRILIA

APRILIA ETV MILLE CAPONORD - PART1 02-2001 Manuel utilisateur

Yamaha

Yamaha 2006 YZF-R1V Manuel utilisateur

Fantic

Fantic Enduro 125 Manuel utilisateur

Ducati

Ducati Supersport 750 desmodue Manuel utilisateur

MV Agusta

MV Agusta 2008 F4 312RR 1078 Manuel d'instructions

Yamaha

Yamaha XVS650A Manuel utilisateur

Yamaha

Yamaha YZF-R6T(C) Manuel

Ducati

Ducati 748 monoposto strada Manuel utilisateur

ATK

ATK 1988 250 Manuel utilisateur

Excelsior-HENDERSON

Excelsior-HENDERSON 1999 HCX Manuel utilisateur

Triumph

Triumph Thunderbird Manuel utilisateur

Yamaha

Yamaha 2006 FJR1300A Manuel utilisateur