KTM 1090 RR kit Manuel utilisateur

KTM 1090 / 1190/ 1050 RR kit installation manual

Thank you for purchasing the KTM 1090 RR kit from RADE/GARAGE. The installation is quite simple,

but may take up to 3 hours because the 1090 has many plastics planes that must be removed before

you can take out the headlight.

0/ See your bike before and after the RR kit is installed

1/ Remove the OEM screen and its holder

a/ Remove the four bots holding the OEM screen and the screen itself

b/ Lift up the OEM screen holders and remove the plastic holder bolts as in the picture. Remove also

the metal plates and keep the OEM screws for later.

2/ Remove the bolts that hold the fairing panels and the OEM headlight

a/ Remove the four bots holding the OEM plastic panels.

b/ Hold the turn signal and CAREULLY lift up the white panel –there is a plastic hook on the back side.

You must remove the white panel in order to access the bolt holding the OEM headlight. If you are not

sure –see the install video on our website.

c/ Next remove the upper two bolts holding the headlight.

d/ To access the bottom bolt, you have to carefully bent the side panel and remove the OEM bolt

3/ Replace the OEM headlight with our LED unit

a/ Now pull out the OEM headlight and mask. Next disconnect the OEM connector. Then remove the

four nut inserts and install them on the R/G headlights bracket.

b/ Assemble the LED headlights. The high beam with shorter tube goes to the upper position and the

low beam with longer tube goes below. Use the M5x16 black bolts (enclosed in the headlights box).

c/ Bolt on the orange resistors with M4 bolts and nuts.

d/ Use the rubber nuts (top right picture) for the upper carbon mask holders and supplied M5 nut

inserts for the bottom mask holders .

c/ Tip for you! Before you connect the LED unit, you have good opportunity to connect your GPS cable,

heat grips cable and other accessories, because the OEM spare power source is now easily accessible.

After you connect the headlights secure the cables with zip tie to avoid bouncing.

d/ insert the LED unit into the same mounting points as the OEM headlight. The bottom bracket will

be secured again using the OEM bolts and the upper bracket with supplied distancers.

4/ Mount the carbon mask

a/ Now install the mesh that will seal the headlights cover. Make sure you place it in the area that will

be under the orange sticker. Than bolt on the headlights cover with M4 rubber nuts and bolts.

b/ When inserting the carbon mask make sure it is placed under the OEM black plastic rim as in the

picture.

c/ Bolt on the mask to the upper bracket with M5x16 bolts and use the plastic washers. Also mount the

top windscreen holders with the OEM screws.

5/ Put the windscreen on!

a/ Before you start the windscreen installation, apply the transparent rim to the edge of the

windscreen. Than start mounting the top two bolts and the two bolts on the sides - via the distancers.

Use the M5x16 bolts and plastic washers.

b/ When mounting the lower bolts use the rubber distance washers in between the carbon mask and

the windscreen. Before you insert the bolts align (using a guide e.g. small screw-driver) the nut insert

with the hole in the carbon mask.

Congratulation! The installation is finished and you can start enjoying your upgraded bike ☺

If you have any questions or feedback, please post it in the following threat on AdvRider forum, we will

be notified, will respond and it might also help others with their questions:

https://advrider.com/f/threads/rade-garage-kits-and-accesorries-for-ktm-1090-1190-

adventure.1351790/

Thanks again.

RADE/GARAGE team

Ce manuel convient aux modèles suivants

Autres manuels KTM Accessoires pour motos

KTM

KTM 61412992044 Mode d’emploi

KTM

KTM Performer 690E Manuel d'instructions d'installation

KTM

KTM 78012016000 Manuel du propriétaire

KTM

KTM 600.12.025.000 Instructions d'utilisation et d'installation

KTM

KTM FAHRGESTELL 400/620 Mode d’emploi

KTM

KTM 60312935044 Manuel du propriétaire

KTM

KTM 78012090000 Manuel du propriétaire

KTM

KTM 64112922000 Manuel du propriétaire

KTM

KTM 79610917000EB Manuel utilisateur

KTM

KTM 00029920000EB Manuel du propriétaire

KTM

KTM 60712932000 Manuel du propriétaire

KTM

KTM META SYSTEM DEFCOM 3.1B Manuel utilisateur

KTM

KTM A61011953044 Manuel utilisateur

KTM

KTM 60312929000 Manuel du propriétaire

KTM

KTM 45312948444 Manuel utilisateur

KTM

KTM 60112924050 Manuel du propriétaire

KTM

KTM 60112929050 Manuel du propriétaire

KTM

KTM Chassis 690 SMC Mode d’emploi

KTM

KTM SADDLE STAY Manuel utilisateur

KTM

KTM PACKTALK EDGE Manuel utilisateur

KTM

KTM 64108915044 Manuel du propriétaire

KTM

KTM 78111994000 Manuel du propriétaire

KTM

KTM TOP-CASE 37 Manuel utilisateur

KTM

KTM 600.12.025.000 Instructions d'utilisation et d'installation

Manuels Accessoires pour motos populaires d'autres marques

SRC

SRC B-TRK502-01-01-SL Manuel utilisateur

3M Speedglas 9100 MP Manuel utilisateur

hepco & becker

hepco & becker 6307520 00 01 Manuel utilisateur

HOMCOM

HOMCOM AA0-077 Manuel utilisateur

hepco & becker

hepco & becker 6307558 00 01 Manuel utilisateur

Wunderkind Custom

Wunderkind Custom 106503-F15 Guide de l'utilisateur

Dräger

Dräger HPS 3500 Manuel utilisateur

M-WAVE

M-WAVE SKI Manuel utilisateur

Kuryakyn

Kuryakyn 6212 Manuel utilisateur

hepco & becker

hepco & becker 6507504 00 01 Manuel utilisateur

Tool it

Tool it PROMAX LCD 9.13G Manuel utilisateur

Custom Dynamics

Custom Dynamics TruWrapz Manuel utilisateur

Roof

Roof RO200 CARBON Manuel utilisateur

Kabuto

Kabuto Japan IBUKI Manuel utilisateur

PUIG

PUIG 5051 Manuel utilisateur

rizoma

rizoma ZTH050 Manuel utilisateur

Joubert

Joubert 10001711 Manuel utilisateur

Sperian

Sperian Optrel p420 Manuel utilisateur